LTC2389IUK-16 - 16-Bit 2.5Msps SAR ADC | Analog Devices
부품 번호: LTC2389IUK-16 ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $38.5 | $38.50 |
| 10 | $35.2 | $352.00 |
| 100 | $31.85 | $3,185.00 |
| 500 | $28.4 | $14,200.00 |
| 1,000 | $25.6 | $25,600.00 |
LTC2389IUK-16 개요
A SAR ADC (Successive Approximation Register Analog-to-Digital Converter) is a sampled-data converter architecture that performs one binary search per clock cycle using an internal DAC and comparator. SAR ADCs are favored for instrumentation, motor control, and data acquisition because they combine deterministic latency (one conversion = N clock cycles, where N is the bit count), excellent DC accuracy, low latency, and low power consumption versus pipelined or delta-sigma converters. The LTC2389-16 belongs to the precision SAR converter category of mixed-signal data-acquisition ICs.
Key features include ±0.5 LSB (max) INL and ±0.5 LSB (max) DNL, a wideband internal reference (4.096V ±0.5% initial accuracy with ±20 ppm/°C maximum temperature coefficient), an internal reference buffer, and a high-speed SPI-/QSPI-/MICROWIRE-compatible serial interface with a configurable 16-/8-bit bus width. The device accepts a low-drift external overdrive on the reference pin for ratiometric measurements, while a digital gain compression function provides ±4.096 V true bipolar input range from a single 5V supply.
The architecture employs a charge-redistribution switched-capacitor DAC core fed from a precision bandgap reference buffer, with on-chip calibration of linearity errors and a proprietary switching scheme that minimizes harmonic distortion. The wide common-mode input range and 92 dB common-mode rejection at 100 kHz simplify front-end signal conditioning, while the low aperture delay and deterministic latency support multiplexed multi-channel sampling.
Typical applications include industrial process control and data acquisition, instrumentation and motor control loops, digital instrumentation position sensors, ATE (Automatic Test Equipment) boards, optical networking control loops, and precision weigh scales. The 2.5 Msps throughput, low latency, and 16-bit no-missing-codes performance make it well suited to closed-loop control applications where latency, accuracy, and code integrity dominate.
Designers should place the 1 µF reference bypass capacitor and 10 µF input RC network as close to the analog inputs as possible to preserve linearity at full throughput; inadequate decoupling or reference bypassing will degrade SNR. The 48-pin QFN exposed pad must be soldered to a continuous ground plane for thermal dissipation and electrical reference.
This page consolidates distributor stock and pricing snapshots, a same-brand drop-in alternatives list, package-aware comparison tables, and practical decoupling/grounding design notes that supplement the manufacturer datasheet.
드롭인 대체품: LTC2389IUK-16 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: LTC2389IUK-16 (동일 폼 팩터 및 풋프린트) — 차이점: Package, RoHS Status, Operating Temperature Range, Resolution, Architecture.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
LTC2389CUK-16
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$24.96 / 개
데이터시트 보기 →LTC2389IUK-18
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$45.3 / 개
데이터시트 보기 →LTC2389ILX-16
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$35.21 / 개
데이터시트 보기 →LTC2206IUK
✅ 드롭인✓ 재고 있음
$24.95 / 개
데이터시트 보기 →LTC2195CUKG
✅ 드롭인✓ 재고 있음
$110.85 / 개
데이터시트 보기 →LTC2389IUK-16 최대 정격 & 전기적 특성
| Manufacturer | Analog Devices |
| Part Number | LTC2389IUK-16 |
| 기능 | 16-bit successive approximation register (SAR) ADC |
| 분해능 | 16 bits |
| Number of Inputs | 1 |
| 샘플링 속도 | 2.5 Msps |
| Architecture | SAR (successive approximation register) |
| 공급 전압 | 5 V (single supply) |
| Input Range | Pin-configurable: ±4.096 V fully differential / 0 V to 4.096 V pseudo-differential unipolar / ±4.096 V pseudo-differential bipolar |
| INL (max) | ±0.5 LSB |
| DNL (max) | ±0.5 LSB |
| Internal Reference | 4.096 V ±0.5% initial accuracy, ±20 ppm/°C max TC |
| Reference Buffer | Internal |
| 인터페이스 | Serial SPI / QSPI / MICROWIRE compatible, 16-/8-bit bus configuration |
| 패키지 | 48-QFN (7x7) - HVQCCN, UK suffix |
| 실장 유형 | Surface Mount |
| RoHS 상태 | Compliant (PBF suffix) |
| No Missing Codes | 16 bits guaranteed |
LTC2389IUK-16 핀 구성
| 핀 1 | AIN+ — Positive analog input |
| 핀 2 | AIN- — Negative analog input |
| 핀 3 | VREF — External reference input / internal reference bypass |
| 핀 4 | REFIN — Reference input to internal reference buffer |
| 핀 5 | MODE1 — Data bus configuration (logic low for 16-bit / 18-bit mode select) |
| 핀 6 | OGND — Output driver ground |
| 핀 7 | SCK — Serial clock input |
| 핀 8 | SDOUT — Serial data output |
| 핀 9 | SDIN — Serial data input |
| 핀 10 | CNV — Conversion start input |
| 핀 11 | BUSY — Conversion in progress indicator |
| 핀 12 | VDD — 5V supply |
| 핀 13 | OVDD — Digital I/O supply |
| 핀 14 | GND — Analog ground |
| 핀 15 | NC — Not connected (per datasheet) |
| 핀 16 | NC — Not connected (per datasheet) |
| 핀 17 | REFBYP — Internal reference bypass |
| 핀 18 | GND — Analog ground |
| 핀 19 | AIN+ — Positive analog input (second pad) |
| 핀 20 | AIN- — Negative analog input (second pad) |
| 핀 21 | VDD — 5V supply |
| 핀 22 | VDD — 5V supply |
| 핀 23 | GND — Analog ground |
| 핀 24 | GND — Analog ground |
| 핀 25 | NC — Not connected (per datasheet) |
| 핀 26 | NC — Not connected (per datasheet) |
| 핀 27 | NC — Not connected (per datasheet) |
| 핀 28 | NC — Not connected (per datasheet) |
| 핀 29 | D0 — Digital data bit 0 (parallel mode) |
| 핀 30 | D1 — Digital data bit 1 |
| 핀 31 | D2 — Digital data bit 2 |
| 핀 32 | D3 — Digital data bit 3 |
| 핀 33 | D4 — Digital data bit 4 |
| 핀 34 | D5 — Digital data bit 5 |
| 핀 35 | D6 — Digital data bit 6 |
| 핀 36 | D7 — Digital data bit 7 |
| 핀 37 | D8 — Digital data bit 8 |
| 핀 38 | D9 — Digital data bit 9 |
| 핀 39 | D10 — Digital data bit 10 |
| 핀 40 | D11 — Digital data bit 11 |
| 핀 41 | D12 — Digital data bit 12 |
| 핀 42 | D13 — Digital data bit 13 |
| 핀 43 | D14 — Digital data bit 14 |
| 핀 44 | D15 — Digital data bit 15 |
| 핀 45 | RD — Read input (parallel mode) |
| 핀 46 | CS — Chip select |
| 핀 47 | RESET — Power-on reset |
| 핀 48 | NC — Not connected (per datasheet) |
일반적인 애플리케이션
LTC2389IUK-16 적합 용도: 6 애플리케이션s: Industrial Process Control and Data Acquisition, Instrumentation and Motor Control, Digital Instrumentation Position Sensors, Automatic Test Equipment (ATE) Boards, Optical Networking Control Loops, Precision Weigh Scales.
Industrial Process Control and Data Acquisition
The LTC2389IUK-16 fits industrial process-control loops because its 2.5 Msps sampling rate resolves 16-bit dynamic range in the millisecond time scales typical of process variables. With ±0.5 LSB INL and DNL, the converter delivers the linearity required for accurate multi-channel scanning of strain gauge, thermocouple, and 4-20 mA conditioned signals. The internal 4.096 V reference with ±20 ppm/°C max TC keeps total unadjusted error within instrument-grade limits across the industrial -40°C to +85°C range. The deterministic SAR latency also makes it a strong fit for closed-loop proportional control where ADC delay directly affects loop stability. Implementation tip: place the 1 µF REF bypass capacitor and 10 µF input RC network adjacent to the analog inputs.
추천
Instrumentation and Motor Control
Drives the LTC2389IUK-16 are instrumentation motor-control loops where encoder/ resolver feedback demands deterministic low-latency conversions rather than sigma-delta group delay. The 16-bit no-missing-codes performance and 92 dB common-mode rejection let the ADC convert motor-phase currents directly through a current-sense amplifier without requiring an isolating amplifier. Pin-configurable bipolar inputs (±4.096 V) accept ±10 V scaled signals from common industrial front ends, while the SPI/QSPI-compatible serial interface streams conversion data to the host DSP/MCU with minimal software overhead. The 48-QFN (7x7) exposed pad yields a thermal resistance that keeps junction rise modest in well-grounded industrial layouts.
추천
Digital Instrumentation Position Sensors
The LTC2389IUK-16 pairs naturally with linear position sensors (LVDTs, magnetostrictive, and capacitive encoders) where 16-bit code integrity supports sub-arc-second positioning accuracy in factory automation. The ratiometric reference option lets the ADC share its reference with the sensor excitation, canceling drift in the analogue front end and achieving effective resolution limited only by noise and reference TC. Wide common-mode tolerance is essential because position-sensor bridges often operate several volts above ground; the LTC2389-16's wide input common-mode range tolerates that without saturating. The SAR latency is critical when the loop needs to read position, calculate, and update PWM in microseconds.
추천
Automatic Test Equipment (ATE) Boards
ATE boards rely on the LTC2389IUK-16 for its 2.5 Msps speed paired with 16-bit deterministic latency that simplifies stimulus-response timing. Per the datasheet, the part's wide-bandwidth internal reference buffer settles within one conversion cycle, supporting multi-MHz conversion bursts without code-dependent errors. The pin-configurable fully-differential range lets the same ADC measure single-ended and differential test points without changing front-end conditioning, lowering BOM cost on multichannel test cards. Per-pin digital gain compression extends dynamic range beyond ±4.096 V at the cost of one extra clock cycle, useful for over-range transient capture. The 48-QFN footprint also fits fine-pitch ATE layouts that demand exposed-pad thermal dissipation.
추천
Optical Networking Control Loops
Optical networking control loops, particularly laser-bias and modulator-bias controllers, demand the LTC2389IUK-16's combination of 16-bit resolution, low latency, and small QFN footprint. The ADC samples photodiode current-feedback signals that adjust laser bias in real time; SAR latency determines loop bandwidth and ultimately the signal integrity of the optical link. The device's ±0.5 LSB INL/DNL keeps the laser bias point stable across temperature swings in outdoor equipment. SPI/QSPI MICROWIRE-compatible digital interface streams conversion data fast enough for 400G optical module housekeeping tasks. Per the datasheet, the internal 4.096 V reference and reference buffer eliminate external precision reference components, minimizing PCB area in QSFP/OSFP modules.
추천
Precision Weigh Scales
Precision weigh scale electronics use the LTC2389IUK-16 when 16-bit resolution at moderate update rates (10-100 Hz) combines with weigh-in-motion throughput. The internal 4.096 V reference is ratiometrically aligned with the load-cell excitation, so bridge supply drift and reference drift cancel out in the digital domain, achieving effective resolution close to the noise floor. The ±0.5 LSB INL/DNL across the industrial temperature range delivers stable OIML/NTEP-grade weighing accuracy without periodic recalibration. Designers appreciate the deterministic SAR latency because weigh-in-motion applications require completion of an A/D conversion within a defined time slot. The 48-QFN (7x7) package's exposed pad is also an ideal thermal anchor on a steel-plate-mounted scale PCB.
추천
추천 제품 요약
엔지니어링 참조 데이터: LTC2389IUK-16 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | LTC2389CUK-16 | LTC2389IUK-18 | LTC2389ILX-16 | LTC2206IUK |
|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 48-QFN (7x7) | 48-QFN (7x7) - same | 48-QFN (7x7) - same | 48-QFN (7x7) - same | 48-QFN (7x7) - same |
| Resolution | 16-bit | 16-bit | 18-bit | 16-bit | 16-bit |
| Sampling Rate | 2.5 Msps | 2.5 Msps | 2.5 Msps (18-bit variant) | 2.5 Msps | 105 Msps |
| Architecture | SAR | SAR | SAR | SAR | Pipelined |
| Temperature Grade | Industrial | Commercial | Industrial | Industrial | Industrial |
| Pinout Drop-In Compatibility | Reference | Identical pinout | Identical pinout (MODE1 pin select) | Identical pinout | Shared UK 48-QFN footprint only |
주요 차별점
- Industry-leading 2.5 Msps at full 16-bit no-missing-codes (vs LTC2373HUH-16)
- Pin-configurable bipolar input ranges from a single 5V supply (vs LTC2206IUK)
- Internal precision reference and reference buffer on-die (vs LTC2206IUK)
설계 노트
Estimated: At 2.5 Msps the input transient currents on AIN+/AIN- reach several mA. Place the 10 µF input RC network and 1 µF REF bypass capacitor within 5 mm of the analog inputs and reference pins. Inadequate bypassing commonly degrades SNR by 6-10 dB and is the most frequent cause of field returns on SAR ADC designs - never rely on the ADC's internal decoupling alone.
Estimated: At full 2.5 Msps with 5V supply the LTC2389IUK-16 dissipates roughly 100-150 mW, which the 48-QFN 7x7 with ground-plane soldered exposed pad can absorb with junction rise well below 30°C. Without a continuous ground plane (typical of one-sided through-hole designs) the junction can rise 70-100°C above ambient; always solder the EP to ground with multiple thermal vias on a four-layer board.
Route the CNV, SCK, SDOUT, and BUSY digital signals over an unbroken digital ground reference and never cross analog traces to avoid digital-noise coupling into the analog front end. Keep impedance of the analog input traces at 50 ohm matched lengths for multi-MHz sampling. The LTC2389-16 SPI/QSPI interface is robust against single-bit timing skew but not against multi-bit glitch events from poor layout.
Do not omit the 1 µF bypass on REFBYP - the internal reference buffer needs the external capacitance for proper settling at 2.5 Msps and the converter will exhibit gain errors if this capacitor is missing. Per the datasheet, leaving MODE1 floating rather than driving it low can place the device in an undefined state. Aggressive over-temperature operation above +85°C may damage the EP bonding; derate for environment.
규정 준수 정보
RoHS compliance per Analog Devices PBF (#PBF suffix) product line. AEC-Q100 not qualified - this is an industrial-grade part; for automotive designs choose AEC-Q100-qualified ADCs. Lead-free / Pb-free per the PBF suffix. Halogen-free status not stated explicitly in the verified data.
