MAX232BAWE+T - 5V 2/2 RS-232 Transceiver | Analog Devices
부품 번호: MAX232BAWE+T ✓ 활성MAX232BAWE+T 개요
An RS-232 transceiver is an interface IC that combines the driver circuitry required to convert logic-level signals into RS-232 voltage levels with receiver circuitry that converts RS-232 signals back into logic levels. This integrated bidirectional interface simplifies point-to-point serial links between equipment such as industrial controllers, test systems, data-acquisition equipment, and computer peripherals. Within the interface hierarchy, the MAX232 belongs to the RS-232 transceiver family of communication interface semiconductors.
The principal feature of the MAX232BAWE+T is its two-transmitter, two-receiver arrangement, allowing two serial channels to be implemented in one device. Its +5 V supply arrangement simplifies integration with conventional +5 V digital logic. The wide -40°C to +125°C operating range makes the device suitable for industrial and extended-temperature equipment, while the 16-SOIC package supports compact, surface-mount PCB construction.
Analog Devices lists the MAX232 family as a production product and identifies the MAX232BAWE+T as a 2/2 full-RS-232 transceiver in a 16-SOIC package. The BAWE+ order code denotes the temperature and package configuration, while the +T suffix identifies tape-and-reel delivery. Because the device combines multiple RS-232 channels in one package, board designers can reduce the number of separate interface ICs while preserving a standardized RS-232 signal interface.
Typical uses include configuration-port links in industrial equipment, serial adapters for test and measurement instruments, control links in data-acquisition systems, and communications between embedded controllers and legacy RS-232 peripherals. The two transmitters can support two outbound signal paths, while the two receivers can monitor two inbound signal paths when the associated system architecture requires separate connections.
For implementation, treat the RS-232 pins as a differential voltage interface rather than ordinary logic-level inputs. Confirm the board's TX, RX, signal-ground, and logic-supply connections against the manufacturer pin-description table, and route the interface connector and transceiver so that external cable transients do not bypass the intended protection strategy. The +T tape-and-reel order code must also match the PCB assembly process.
This page combines the manufacturer product information with package-level guidance, structured application analysis, and same-footprint replacement options. It is intended to accelerate component identification while preserving the distinction between the production MAX232BAWE+T configuration and other electrical or package variants in the broader MAX232 family.
드롭인 대체품: MAX232BAWE+T — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: MAX232BAWE+T (동일 폼 팩터 및 풋프린트) — 차이점: Package, Product Type, Maximum Data Rate, Supply Voltage, Interface Standard.
MAX232EIPWR
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →MAX232EWE+T
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →MAX232EEWE+
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →MAX232AEWE+
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →MAX232ECDWR
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →MAX232BAWE+T 사양
| Product Type | RS-232 transceiver |
| Transmitter Count | 2 transmitters |
| Receiver Count | 2 receivers |
| RS-232 Mode | Full RS-232 |
| 공급 전압 | +5 V |
| 동작 온도 범위 | -40°C to +125°C |
| 패키지 | 16-SOIC |
| 핀 수 | 16 pins |
| 실장 유형 | Surface mount |
| Delivery Configuration | Tape and reel (+T) |
| Manufacturer Order Code | MAX232BAWE+T |
| Manufacturer | Analog Devices |
| Production Status | Production |
| Datasheet Revision | Rev. 18 |
| Interface Family | RS-232 |
| Channel Configuration | 2 transmit and 2 receive channels |
MAX232BAWE+T 16-soic 핀 구성 가이드
MAX232BAWE+T(16-soic 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: MAX232BAWE+T.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
MAX232BAWE+T 적합 용도: 6 애플리케이션s: Industrial Controller Serial Port, Test and Measurement Instrument Interface, Data Acquisition System, Point-to-Point Equipment Link, Embedded Serial Adapter, Legacy Peripheral Configuration Port.
Industrial Controller Serial Port
The MAX232BAWE+T fits an industrial controller that needs two RS-232 transmitter paths and two receiver paths while operating from a +5 V logic supply. Its -40°C to +125°C rating provides useful thermal margin for factory equipment, and the 16-SOIC package simplifies routing to a legacy DB9 or terminal connector. The transmitter outputs connect to the corresponding RX inputs at the opposite endpoint, while a common signal ground establishes the return path. Because the interface is not a 3.3 V UART, the host controller still needs a suitable logic-level side, and the PCB should minimize exposed connector traces and provide the protection required by the final cable environment.
추천
Test and Measurement Instrument Interface
A bench instrument or automated test system can use the MAX232BAWE+T to expose two command-output and two status-input channels through an RS-232 connector. The full RS-232 interface avoids adding separate level-shifting ICs for each direction, and the two-transmitter, two-receiver arrangement supports multi-channel instrument communication. The +5 V supply aligns with many legacy instrument control boards. During layout, keep the transceiver close to the connector, route TX and RX away from sensitive analog nodes, and use the datasheet grounding and external-charge-pump recommendations so repeated cable connections do not degrade measurement accuracy.
추천
Data Acquisition System
The MAX232BAWE+T is suitable for communicating between a data-acquisition controller and an external computer, programmable instrument, or relay interface that still uses RS-232. Two receiver channels can collect separate status or interlock signals, while two transmitter channels can carry commands and data. Its extended -40°C to +125°C range supports laboratory and industrial environments, but high-voltage switching stages should be separated from the communication section. A practical implementation places the MAX232 near the serial connector, uses a low-noise ground connection, and validates every TX/RX signal with scope measurements before the system is deployed in the field.
추천
Point-to-Point Equipment Link
The MAX232BAWE+T can bridge two legacy pieces of equipment when each end exposes two RS-232 signal channels. One transmitter on each device drives the opposite receiver, creating two independent communication paths without requiring a separate line-driver package for each signal. This arrangement is common in service equipment, configuration links, and simple industrial controllers. The design should treat the RS-232 connector as an external-entry point, provide consistent signal grounding between devices, and avoid sharing connector ground with high-current return paths. Because standard RS-232 is unbalanced and point-to-point, the implementation should also account for cable length and the selected data rate.
추천
Embedded Serial Adapter
The MAX232BAWE+T can serve as the RS-232 side of an embedded serial adapter built around a modern controller with a separate logic-level UART. The controller communicates through the transceiver, which handles the voltage conversion between its digital I/O and the full RS-232 interface. Using two transmitter and two receiver channels avoids adding another transceiver when the product exposes more than one legacy port. The 16-SOIC package is appropriate for automated PCB assembly, and the +T order code supports reel-based production. Firmware and hardware should provide software flow control when the connected device cannot tolerate an unexpected assertion on the receive line.
추천
Legacy Peripheral Configuration Port
The MAX232BAWE+T can connect a newer controller to a legacy printer, scanner, display, or service peripheral that still uses RS-232. One transmitter and receiver pair may carry commands and responses, while the second pair provides a status or handshake path. Its production status and surface-mount package support compact adapter designs, and the -40°C to +125°C specification allows use in equipment beyond room-temperature consumer environments. PCB implementation must match the peripheral connector's TX, RX, and ground assignments, because RS-232 signal names are defined from the viewpoint of the data-terminal side and can otherwise be reversed.
추천
추천 제품 요약
엔지니어링 참조 데이터: MAX232BAWE+T — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MAX232EIPWR | MAX232EWE+T | MAX232EEWE+ | MAX232AEWE+ | MAX232ECDWR |
|---|---|---|---|---|---|---|
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Supply Voltage | +5 V | +5 V | +5 V | +5 V | +5 V | +5 V |
| RS-232 Mode | Full RS-232 | Full RS-232 | Full RS-232 | Full RS-232 | Full RS-232 | Full RS-232 |
| Enhanced ESD Design | Standard MAX232 configuration | E version; 8 kV contact and 15 kV air discharge rating | E version; 8 kV contact and 15 kV air discharge rating | E version; 8 kV contact and 15 kV air discharge rating | A-temperature configuration | E version; 8 kV contact and 15 kV air discharge rating |
| Delivery Configuration | Tape and reel (+T) | Tape and reel | Tape and reel (+T) | Non +T order code | Non +T order code | Tape and reel |
주요 차별점
- Extended-temperature operation (vs MAX232AEWE+)
- Two transmitters and two receivers in one package (vs MAX232EIPWR)
- Production status for the exact family (vs MAX232ECDWR)
설계 노트
Place the MAX232BAWE+T close to the RS-232 connector and keep the TX, RX, and signal-ground routes short. Separate connector-side traces from clocks, ADC inputs, and other sensitive analog nets to reduce susceptibility to cable transients. Match the PCB land pattern to the wide 16-SOIC package and follow the manufacturer drawing for pin 1 orientation; the +T suffix identifies reel packaging but does not change the electrical pinout.
Do not assume that every MAX232 order code is interchangeable. MAX232BAWE+T, MAX232EIPWR, MAX232EWE+T, and the other listed candidates use different family suffixes for features, temperature grades, or ordering. Before substituting, compare the manufacturer pin-description table, channel count, supply arrangement, temperature range, and ESD design. Also verify that the selected order code includes tape-and-reel packaging when the assembly process requires it.
RS-232 driver outputs are relatively slow but can still generate edge-related noise and reflect on imperfect cable terminations. Keep output routing away from sensitive receiver and analog inputs, provide a solid signal-ground reference, and avoid routing the interface directly beneath clocks or power-converter switch nodes. Validate conducted and radiated behavior in the finished enclosure because connector cables can introduce noise not represented by a bare-board test.
규정 준수 정보
The manufacturer identifies MAX232 as a production family and the exact MAX232BAWE+T as a +5 V, 2/2, 16-SOIC device rated from -40°C to +125°C. Specific environmental and material-compliance declarations for this order code were not stated in the available product information.