MAX3095ESE/GG8 - 10Mbps Quad RS-485 Receiver | Analog Devices
부품 번호: MAX3095ESE/GG8 ✗ 단종MAX3095ESE/GG8 개요
A differential line receiver is an interface circuit that interprets the voltage difference between a pair of signal conductors. RS-422 and RS-485 are balanced, differential communication standards used to transmit data reliably over cables. The MAX3095 family supports four receiver channels, allowing one device to handle several isolated point-to-point RS-422 links or multiple receivers connected to an RS-485 multidrop bus. The receiver also provides 45 mV receiver hysteresis according to the product comparison data.
The MAX3095/MAX3096 family is specified for a 4.75 V to 5.25 V supply and a maximum data rate of 10 Mbps. Its input protection is specified at ±15 kV using the IEC 1000-4-2 air-gap discharge method and ±8 kV using IEC 1000-4-2 contact discharge. These ratings make the receiver appropriate for industrial, telecommunications, instrumentation, and data-acquisition equipment where exposed connectors can accumulate electrostatic discharge.
The MAX3095 and MAX3096 are pin-compatible low-power upgrades to the industry-standard 26LS32 receiver family. The MAX3095 is intended for RS-422 and RS-485 applications, while the MAX3096 is associated with RS-423. Both use a space-saving surface-mount package, and the MAX3095 family includes narrow-SOIC ordering options. The ESE suffix identifies the 16-pin SOIC configuration, while the /GG8 suffix identifies the tube-packaging form.
Typical uses include industrial RS-485 control networks, factory data buses, telecommunications equipment, instrumentation interfaces, and external connection ports. Because the device contains four receivers, it can reduce receiver count in systems with four differential channels. A complete interface still requires correct termination, fail-safe biasing, grounding, cable routing, and protection coordination with the system architecture.
Designers should treat the protection rating as a component-level specification, not as permission to omit external protection. Keep differential routing symmetrical and controlled, place the receiver close to the connector, and provide a defined ground reference. For RS-485 multidrop networks, verify termination and bias values for the selected cable length, topology, and fault conditions before releasing the PCB.
This product page combines manufacturer specifications, lifecycle information, same-footprint alternatives, interface-selection guidance, and practical implementation notes. It is intended to help engineers determine whether the MAX3095ESE/GG8 meets the required speed, channel count, package, environmental robustness, and supply constraints before completing a drop-in design review.
드롭인 대체품: MAX3095ESE/GG8 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: MAX3095ESE/GG8 (동일 폼 팩터 및 풋프린트) — 차이점: Package, Number of Receivers, Data Rate, Number of Drivers, Product Type.
MAX3095ESE+
✅ 드롭인가격 문의
데이터시트 보기 →MAX3095EEE+
✅ 드롭인가격 문의
데이터시트 보기 →MAX3095CEE+
✅ 드롭인가격 문의
데이터시트 보기 →MAX3096ESE/GG8
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
MAX3096ESE+
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
MAX3095ESE/GG8 사양
| Receiver Configuration | 4 receivers |
| Supported Standards | RS-422 and RS-485 |
| Maximum Data Rate | 10 Mbps |
| Supply Voltage Range | 4.75 V to 5.25 V |
| Receiver Hysteresis | 45 mV |
| Air-Gap ESD Protection | ±15 kV using IEC 1000-4-2 |
| Contact ESD Protection | ±8 kV using IEC 1000-4-2 |
| Number of Drivers | 0 drivers |
| Number of Receivers | 4 receivers |
| 패키지 | 16-pin SOIC |
| 실장 유형 | Surface mount |
| Packaging | Tube |
| Product Family | MAX3095 quad differential receiver |
| Pin-Compatibility Reference | 26LS32 receiver family |
MAX3095ESE/GG8 16-pin soic 핀 구성 가이드
MAX3095ESE/GG8(16-pin soic 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: MAX3095ESE/GG8.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
MAX3095ESE/GG8 적합 용도: 6 애플리케이션s: Industrial RS-485 Control Bus, Telecommunications Equipment Interface, Data Acquisition and Instrumentation, RS-422 Point-to-Point Communication, External I/O and Connector Protection, Factory Automation Multi-Axis Controller.
Industrial RS-485 Control Bus
The MAX3095ESE/GG8 fits receive ports on industrial controller boards that must decode four differential RS-485 channels at up to 10 Mbps. Its four integrated receivers reduce the number of separate receiver packages needed on multi-axis machinery, remote I/O, or factory-control equipment. The specified ±15 kV IEC 1000-4-2 air-gap and ±8 kV contact ESD protection add useful robustness at a connector-adjacent interface. The 4.75 V to 5.25 V operating range suits a conventional 5 V rail. Design still requires correct common-mode grounding, cable termination, fail-safe biasing, and external surge protection when field cables extend beyond the enclosure.
추천
Telecommunications Equipment Interface
The MAX3095ESE/GG8 is appropriate for telecommunications equipment that receives differential data from backplanes, remote modules, or protected cable ports. A 10 Mbps maximum data rate supports faster control and status links than low-speed legacy receiver families, while four channels allow one package to serve several independent receiver functions. Its low-power receiver architecture and surface-mount 16-pin SOIC construction simplify board integration where space is limited. ESD protection on every receiver input improves resilience at accessible interfaces, but engineers should coordinate it with chassis grounding, isolation boundaries, and a complete surge-protection strategy for externally connected lines.
추천
Data Acquisition and Instrumentation
The MAX3095ESE/GG8 can receive measurement and control data from balanced sensor or instrument links in laboratory and industrial acquisition systems. Four differential inputs provide a practical advantage when several transducers or remote instrument channels share the same receiver package. The 45 mV hysteresis helps reject small noise fluctuations around the switching threshold, and the 10 Mbps capability allows the receiver to handle higher-rate digital status links in addition to slower sensor interfaces. PCB implementation should preserve differential symmetry, provide a stable reference ground, and separate sensitive analog paths from high-energy cable transients.
추천
RS-422 Point-to-Point Communication
The MAX3095ESE/GG8 supports four RS-422 point-to-point receive channels where a transmitter drives one differential pair per channel. The receiver-only architecture is appropriate when the system already contains separate transmit circuitry and needs a dedicated, protected receive section. Its 10 Mbps capability accommodates many moderate-distance control, status, and synchronization links, while 45 mV hysteresis improves noise immunity. Unlike a multidrop RS-485 network, each RS-422 link is generally point-to-point, so termination and biasing should be designed separately for each channel according to cable length and source configuration.
추천
External I/O and Connector Protection
The MAX3095ESE/GG8 is useful on boards with external differential I/O connectors where electrostatic discharge is a primary concern. With every receiver input protected to ±15 kV for IEC 1000-4-2 air-gap discharge and ±8 kV for contact discharge, it provides component-level protection against ESD entering through attached cables. The four-channel count permits several protected receive inputs without duplicating discrete receiver circuitry. Place the device near the connector entry point, route the differential pair as a tightly coupled pair, establish a low-impedance chassis-to-board ground strategy, and add coordinated surge protection if the port also faces lightning or industrial transients.
추천
Factory Automation Multi-Axis Controller
A multi-axis motion or factory-automation controller can use the MAX3095ESE/GG8 to receive four differential status or command links from remote axes and controllers. Consolidating four receivers into one 16-pin SOIC can simplify routing compared with four separate packages, while the 10 Mbps rate is suitable for many embedded control and diagnostic channels. The device's receiver-only organization means transmit functions must be provided separately when the board also sends commands. Engineers should evaluate cable length, node topology, ground potential differences, and fault-safe biasing before deciding whether an isolated interface is required.
추천
추천 제품 요약
엔지니어링 참조 데이터: MAX3095ESE/GG8 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MAX3095ESE+ | MAX3095EEE+ | MAX3095CEE | MAX3096ESE/GG8 | MAX3096ESE+ |
|---|---|---|---|---|---|---|
| Package | 16-pin SOIC | 16-pin SOIC - same | 16-pin SOIC - same | 16-pin SOIC - same | 16-pin SOIC - same | 16-pin SOIC - same |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Receiver Configuration | 4 receivers | 4 receivers | 4 receivers | 4 receivers | 4 receivers | 4 receivers |
| Supported Protocol | RS-422 and RS-485 | RS-422 and RS-485 | RS-422 and RS-485 | RS-422 and RS-485 | RS-423 | RS-423 |
| Number of Drivers | 0 | 0 | 0 | 0 | 0 | 0 |
주요 차별점
- Four high-speed differential receivers in one interface package (vs MAX308ESE+T)
- Documented ESD protection on every receiver input (vs MAX3095CEE)
- Pin-compatible MAX309x family options (vs MAX3096ESE/GG8)
설계 노트
Route each differential receiver pair as a tightly coupled pair with continuous reference to the board ground plane. Place the MAX3095ESE/GG8 close to the connector entry and minimize the distance from the connector pins to the receiver inputs. Avoid routing these signals adjacent to switching nodes or high-current return paths. Maintain symmetric spacing between each pair so external noise induces similar voltage disturbances on both conductors.
Do not treat the specified ESD ratings as a complete industrial surge-protection solution. The receiver provides ±15 kV air-gap and ±8 kV contact protection under IEC 1000-4-2, but lightning, motor transients, and sustained overvoltage require coordinated external protection. Determine whether the interface requires isolation, surge suppressors, common-mode chokes, or a chassis-ground network, and validate the complete protection scheme at the connector boundary.
Design the receiver's 5 V supply rail within the 4.75 V to 5.25 V operating range and account for noise from adjacent digital and switching circuitry. Place local supply and ground-plane connections close to the device, and avoid sharing narrow supply paths with high-current loads. Review the manufacturer data sheet for the required bypass capacitance and place those components at the specified power pins.
For RS-485 multidrop networks, calculate termination and fail-safe bias values for the actual cable length, topology, node count, and fault conditions. For RS-422 point-to-point links, evaluate termination separately at each receiver. Do not add termination automatically to every channel, because incorrect termination can reduce signal integrity or increase loading on the bus.
규정 준수 정보
The MAX3095/MAX3096 family uses IEC 1000-4-2 ESD test methods for its stated input protection. RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive-qualification status are not established by the captured product information.