MAX3221IPWG4 - 250kbps RS-232 Transceiver | Texas Instruments
부품 번호: MAX3221IPWG4 ✓ 활성MAX3221IPWG4 개요
An RS-232 transceiver is an interface IC that converts logic-level signals from a controller or embedded processor into RS-232 levels and converts incoming RS-232 signals back into logic levels. Within the broader interface-IC and data-communication hierarchy, the MAX3221 provides a compact single-channel solution for industrial control, embedded instrumentation, POS equipment, and legacy serial-port connectivity.
The principal operating features include a 3 V to 5.5 V supply range, a maximum signaling rate of 250 kbps, one driver and one receiver, and ±15 kV ESD protection. Its low supply current supports power-conscious equipment, while the integrated charge pumps eliminate the need for an external ±12 V supply. These characteristics suit systems where reliable serial communication is required without the space and power burden of a multi-channel transceiver.
The MAX3221 architecture separates the logic-side interface from the RS-232-side pins so that a host UART can connect directly to the transceiver. Its RS-232 implementation supports the electrical signaling requirements identified by the manufacturer as TI A/EIA-232-F. The device is suited to point-to-point links where one transmitter communicates with one receiver through a protected cable or connector.
Typical uses include industrial serial controllers, test equipment, data-acquisition systems, embedded-service interfaces, and legacy peripheral connections. In these systems, the MAX3221 can bridge a 3.3 V or 5 V UART to an RS-232 port while providing ESD protection at the connector-facing pins. Designers should verify signal levels, connector wiring, ground references, and cable length in the final system.
For a new PCB, follow the pin-description table and typical application circuit in the manufacturer datasheet when assigning traces and decoupling capacitors. Keep the charge-pump capacitor and I/O routing within the layout recommendations, and provide a low-impedance return path between connected equipment to reduce common-mode voltage and improve communication reliability.
This page consolidates the MAX3221IPWG4 operating limits, package information, sourcing structure, verified drop-in candidate, comparison fields, and practical RS-232 design considerations into a compact engineering reference for component selection and board design.
드롭인 대체품: MAX3221IPWG4 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
MAX3221IPWR
✅ 드롭인가격 문의
데이터시트 보기 →MAX3221IPWG4 사양
| Product Type | Single-channel RS-232 line driver/receiver |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| Number of Drivers | 1 |
| Number of Receivers | 1 |
| ESD Protection | ±15 kV |
| 공급 전류 | 1 µA |
| Logic Compatibility | 3.3 V and 5 V RS-232 interface |
| 패키지 | 16-pin TSSOP |
| Package Width | 4.40 mm |
| 실장 유형 | Surface mount |
| Charge Pump | On-chip dual charge-pump circuit |
| RS-232 Compliance | TI A/EIA-232-F |
MAX3221IPWG4 4.40 mm 핀 구성 가이드
MAX3221IPWG4(4.40 mm 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: MAX3221IPWG4.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
MAX3221IPWG4 적합 용도: 6 애플리케이션s: Industrial Serial Controller Interface, Embedded Data-Acquisition Equipment, Point-of-Sale Peripheral Link, Legacy Service and Configuration Port, Test and Measurement Equipment, Remote Monitoring and Telemetry.
Industrial Serial Controller Interface
The MAX3221IPWG4 fits a single-port industrial controller because it converts one UART channel to RS-232 while operating from 3 V to 5.5 V. Its 250 kbps maximum data rate supports moderate-speed command and status links, while the integrated dual charge pumps avoid an external bipolar supply. The ±15 kV ESD rating is useful on connector-facing equipment, although the final industrial design must still meet its enclosure, surge, grounding, and environmental requirements.
추천
Embedded Data-Acquisition Equipment
For an embedded measurement instrument, the MAX3221IPWG4 provides a compact RS-232 link from a low-voltage controller to a host computer. The 16-pin TSSOP package preserves PCB area, the 3 V to 5.5 V supply supports 3.3 V systems, and the 250 kbps rate is suitable for many configuration and sample-control commands. Place the transceiver close to the serial connector and follow the recommended charge-pump capacitor layout to minimize signal and EMI issues.
추천
Point-of-Sale Peripheral Link
A point-of-sale terminal can use the MAX3221IPWG4 when a legacy peripheral requires a single RS-232 port. The single driver and receiver cover a point-to-point cable connection, and the 250 kbps maximum rate is appropriate for many peripheral command protocols. Its low 1 µA supply-current figure also suits compact equipment. Designers should confirm the peripheral’s logic timing, connector pinout, cable length, and grounding requirements before implementation.
추천
Legacy Service and Configuration Port
The MAX3221IPWG4 is useful for exposing a service or configuration interface on equipment that retains an RS-232 connector. A single channel is sufficient for system-level commands without occupying space for an unused multi-driver device, and operation from 3 V to 5.5 V simplifies integration with modern logic. Add external protection appropriate to the connector environment, maintain a common ground reference, and verify the serial baud-rate tolerance in the complete system.
추천
Test and Measurement Equipment
The MAX3221IPWG4 can connect a bench instrument or field tester to a host over RS-232. Its 250 kbps capability supports measurement commands and moderate data-transfer duties, while ±15 kV ESD protection adds resilience to frequently connected external leads. The 16-pin TSSOP package is useful in compact portable instruments. Keep the RS-232 traces away from sensitive analog sections and use the manufacturer’s recommended charge-pump and bypass-capacitor arrangement.
추천
Remote Monitoring and Telemetry
For a remote monitoring enclosure, the MAX3221IPWG4 offers a compact path for configuration and telemetry commands over a wired RS-232 link. The 3 V to 5.5 V operating range supports low-voltage industrial electronics, and the integrated charge pumps simplify the power architecture. The 250 kbps rate is suitable for supervisory data rather than high-volume streaming. Use transient protection and an isolated or protected interface strategy when the cable leaves the controlled enclosure.
추천
추천 제품 요약
엔지니어링 참조 데이터: MAX3221IPWG4 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MAX3221IPWR |
|---|---|---|
| Manufacturer | Texas Instruments | Texas Instruments |
| Package | 16-pin TSSOP | 16-pin TSSOP |
| Device Type | Single-channel RS-232 line driver/receiver | Single-channel RS-232 line driver/receiver |
| Supply Voltage Range | 3 V to 5.5 V | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps | 250 kbps |
| ESD Protection | ±15 kV | ±15 kV |
| Drivers and Receivers | 1 driver and 1 receiver | 1 driver and 1 receiver |
| Charge-Pump Architecture | On-chip dual charge-pump circuit | On-chip dual charge-pump circuit |
| RS-232 Compliance | TI A/EIA-232-F | TI A/EIA-232-F |
주요 차별점
- Single-channel integration in a compact 16-pin TSSOP package (vs MAX3221IPWR)
- Low-voltage operation compatible with modern embedded systems (vs MAX3221IPWR)
- Connector-facing ESD protection (vs MAX3221IPWR)
설계 노트
Place the charge-pump capacitors and bypass capacitor exactly as shown in the manufacturer’s typical application circuit, keeping each capacitor close to its associated IC pin. Route the RS-232 driver and receiver nets directly toward the connector while keeping them separated from sensitive analog and high-speed clock traces. The compact 16-pin TSSOP footprint leaves little routing margin, so verify every pad assignment against the pin-description table before releasing artwork.
Provide a continuous, low-impedance ground path between the transceiver, logic circuit, and connected RS-232 equipment. RS-232 signal levels are referenced to ground, and ground-potential differences between separately powered systems can impair reception or cause stress. A common ground does not replace isolation; use an isolated interface strategy when the connected equipment may have substantial ground-potential differences.
Do not treat the 3 V to 5.5 V MAX3221 supply range as permission to exceed the receiver’s permitted logic or signal limits. Confirm UART logic levels, baud-rate tolerance, cable length, connector wiring, and the remote device’s electrical characteristics. Also distinguish the 250 kbps maximum signaling rate from guaranteed application throughput, which can be lower because of protocol framing and receiver timing.
The MAX3221 uses charge-pump circuitry, so follow the datasheet’s recommended capacitor values and placement to limit switching transients. Keep the charge-pump loop compact and away from high-impedance inputs and precision analog front ends. If the RS-232 cable is long or routed near sensitive equipment, add suitable connector-side protection and validate conducted and radiated emissions in the final enclosure.
규정 준수 정보
The ordering suffix includes a green-compliance indicator, but explicit RoHS, REACH, lead-free, halogen-free, AEC-Q100, and conflict-minerals statements were not published in the cited product summaries. Compliance fields remain unknown until confirmed in the manufacturer product documentation.