MAX365CSE+ - Quad SPST Analog Switch | Analog Devices
부품 번호: MAX365CSE+ ✓ 활성MAX365CSE+ 개요
An analog switch is a semiconductor device that connects or disconnects an analog signal path under digital control. The MAX365 belongs to the analog switch hierarchy within interface ICs and signal-routing semiconductors. Unlike a mechanical relay, it can change connection states electronically with compact packaging and low external component requirements. The MAX365 is specifically configured as four normally open SPST switches, making each channel independent when the device supports separate control inputs.
The MAX365 family provides on-resistance below 85 ohms across the analog signal range, with channel matching within 2 ohms and maximum on-resistance variation of 9 ohms. These characteristics help minimize signal attenuation and gain errors when different channels are selected in sequence. The four-channel architecture also allows one package to replace multiple individual switch functions in signal-routing designs.
The manufacturer describes the MAX365 as a precision quad SPST analog switch with low on-resistance, low leakage, and power-off isolation. A 250 ns switching figure is associated with the device. Because the MAX365CSE+ uses normally open contacts, each switched path is disconnected until its corresponding control signal activates the channel. The exact supply-voltage range, control thresholds, leakage limits, and detailed timing conditions should be confirmed in the manufacturer data sheet before final circuit design.
Typical uses include battery-powered test equipment, data-acquisition systems, analog signal multiplexing, precision measurement circuits, and industrial control interfaces. The device can also isolate signal sources when power is absent or when a system requires a controlled connection rather than a permanently closed path. Its 16-pin SOIC package supports conventional surface-mount assembly and compact board layouts.
PCB design should keep each switched signal trace short and place input and output routing away from fast digital control or switching nodes. Verify the logic levels and supply rails against the manufacturer data sheet, especially in mixed 3.3 V and 5 V systems. Confirm whether normally open behavior is required, rather than selecting a normally closed alternative, because the open and closed families provide different default signal paths.
This page combines the MAX365 family specifications, package information, application guidance, and pin-compatible family comparisons to support faster component selection and PCB design. It also organizes sourcing questions, replacement options, and practical implementation considerations around the exact MAX365CSE+ ordering code.
드롭인 대체품: MAX365CSE+ — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
MAX365CSE
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MAX365EESE+
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
MAX365AESE+
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
MAX365CSE+ 최대 정격 & 전기적 특성
| Switch Type | Single-pole single-throw (SPST) |
| Number of Channels | 4 circuits |
| Switch Configuration | 4 normally open (NO) channels |
| On-Resistance | 85 ohm maximum |
| On-Resistance Matching | Within 2 ohm between channels |
| On-Resistance Variation | 9 ohm maximum across the analog signal range |
| Switching Time | 250 ns |
| Power-Off Isolation | Supported |
| 패키지 | 16-pin SOIC |
| Package Code | SOP |
| Package Shape | Rectangular |
| 실장 유형 | Surface mount |
| Temperature Grade | Commercial |
| Number of Terminals | 16 |
MAX365CSE+ rectangular 핀 구성 가이드
MAX365CSE+(rectangular 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: MAX365CSE+.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
MAX365CSE+ 적합 용도: 6 애플리케이션s: Data Acquisition Signal Multiplexing, Battery-Powered Test Equipment, Precision Measurement Interfaces, Analog Signal Routing, Industrial Control Interfaces, Automated Test Fixtures.
Data Acquisition Signal Multiplexing
The MAX365CSE+ fits four-channel analog signal multiplexing when the instrument must route several sensor or test-node signals into a shared measurement path. Each normally open SPST section can connect one selected source without affecting the other paths, while the 85 ohm maximum on-resistance and matching within 2 ohms help limit channel-dependent attenuation. Engineers should include the switch resistance in the source-impedance and amplifier-gain calculation, then verify settling behavior against the 250 ns switching figure and system bandwidth.
추천
Battery-Powered Test Equipment
The MAX365CSE+ is useful in battery-powered test equipment where isolated analog paths, low external component count, and compact surface-mount construction help control board area. The four normally open channels can connect external test inputs only when requested, avoiding an unintended connection between the fixture and instrument circuitry. Power-off isolation provides an additional design consideration when the source and equipment grounds may not share a common reference, although leakage and supply limits must be checked for the operating voltage.
추천
Precision Measurement Interfaces
The MAX365CSE+ suits precision measurement interfaces that switch between resistive, voltage, or instrumentation-amplifier inputs. Its maximum on-resistance of 85 ohms, on-resistance matching within 2 ohms, and maximum variation of 9 ohms help reduce errors that would otherwise appear as gain differences between channels. Because the switch contributes to the complete signal path, the amplifier input impedance and sensor impedance should be evaluated together with the switch specifications to determine the resulting loading and measurement uncertainty.
추천
Analog Signal Routing
The MAX365CSE+ provides compact analog routing for circuits that must connect a source to one of several downstream destinations or isolate a path during a test sequence. Four independent normally open SPST channels offer a straightforward alternative to multiple discrete relays when switching speed and board area are priorities. Layout should minimize trace length around the switched nodes and keep control signals away from sensitive analog conductors, reducing capacitive coupling into the switched path.
추천
Industrial Control Interfaces
The MAX365CSE+ can route low-voltage analog command or feedback signals in industrial control equipment while keeping the implementation within a 16-pin SOIC footprint. Its normally open behavior is useful when a default disconnected state is safer or more convenient than a permanently connected path. For equipment exposed to temperature variation, electrical noise, or long wiring runs, select the appropriate family temperature grade and verify control thresholds and leakage against the actual industrial environment.
추천
Automated Test Fixtures
The MAX365CSE+ is appropriate for automated fixtures that must connect test signals only during a commanded measurement interval. The normally open topology prevents the DUT path from remaining connected when the channel is inactive, and four channels can manage several fixture nodes within one package. The 250 ns switching figure supports relatively fast state changes, but fixture capacitance, cable length, and the required settling time must be included in the complete timing budget.
추천
추천 제품 요약
엔지니어링 참조 데이터: MAX365CSE+ — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MAX365CSE | MAX365EESE+ | MAX365AESE+ |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 16-pin SOIC | 16-pin SOIC - same | 16-pin SOIC - same | 16-pin SOIC - same |
| Switch Type | Quad SPST | Quad SPST | Quad SPST | Quad SPST |
| Number of Channels | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Default Contact State | Normally open | Normally open | Normally open | Normally open |
| On-Resistance | 85 ohm maximum | 85 ohm maximum | 85 ohm maximum | 85 ohm maximum |
| On-Resistance Matching | Within 2 ohm between channels | Within 2 ohm between channels | Within 2 ohm between channels | Within 2 ohm between channels |
| On-Resistance Variation | 9 ohm maximum | 9 ohm maximum | 9 ohm maximum | 9 ohm maximum |
| Switching Time | 250 ns | 250 ns | 250 ns | 250 ns |
| Power-Off Isolation | Supported | Supported | Supported | Supported |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount |
주요 차별점
- Four independent normally open channels in one package (vs MAX365CSE)
- Broader environmental option within the same footprint (vs MAX365CSE)
- Automotive-family sourcing option without package conversion (vs MAX365CSE)
설계 노트
Treat the switched analog path as a resistance in series with the source. The MAX365CSE+ is specified with 85 ohm maximum on-resistance, so include that value in the source-loading and amplifier-gain calculations. Use the 2 ohm channel-matching and 9 ohm maximum variation limits when evaluating channel-dependent error, and verify that the selected downstream amplifier presents sufficiently high input impedance.
Place the MAX365CSE+ close to the source and destination pads so the switched path remains short. Route sensitive analog traces away from digital control inputs, clock-like signals, and other high-impedance nodes. Because a 16-pin SOIC provides limited spacing between channels, maintain clearance between adjacent switched nets and ground the unused PCB area conservatively to reduce coupling.
Do not substitute the normally closed MAX364 family when the circuit depends on the MAX365 default open state. A common footprint does not guarantee equivalent system behavior: the contact state before control is asserted changes whether a test source, sensor, or signal node is connected. Confirm the control logic, supply levels, leakage, and operating-temperature grade against the manufacturer data sheet before releasing the PCB.
Confirm the control-signal voltage levels and the device supply requirements before connecting external logic. The four control inputs may be driven from a different logic family, but mixed 3.3 V and 5 V systems require the actual input thresholds from the manufacturer data sheet. A 250 ns switching figure does not by itself guarantee that the analog node has settled; include output capacitance, source impedance, and measurement bandwidth in timing analysis.
규정 준수 정보
The MAX365 family documentation identifies the device as precision, quad, normally open SPST analog switches. Family-specific RoHS, REACH, halogen-free, conflict-minerals, and automotive qualification statements were not present for MAX365CSE+, so these fields remain unknown or not applicable as appropriate.