MC33661PEF LIN Transceiver with Wake | NXP | 8-SOIC
부품 번호: MC33661PEF ✓ 활성MC33661PEF 개요
A LIN transceiver is an interface IC that connects a host microcontroller or programmable logic controller to a Local Interconnect Network bus. LIN is a low-cost, single-wire, automotive-oriented communication network used for distributed electronic control units. The MC33661PEF provides the physical communication layer at the node, while the connected controller handles message framing, data interpretation, diagnostics, and application logic. In the product hierarchy, it is an interface transceiver, a communication IC, and a semiconductor device for embedded vehicle networks.
The MC33661PEF distinguishes itself through its wake-up function and enhanced LIN-interface positioning. Wake support allows a connected node to detect a targeted bus activity rather than remain completely inactive, helping conserve power in parked vehicles. Because LIN buses commonly contain several nodes and loads different wake patterns, controller-side wake recognition remains important. The half-duplex architecture supports bidirectional communication over the single LIN conductor while sharing one physical network among multiple modules.
The MC33661PEF is manufactured in the 8-SOIC package identified as 0.154 inch wide and 3.90 mm long by the manufacturer catalog information. Its interface-oriented design is intended to be placed near the vehicle harness connector or protected LIN network entry point. Component placement, grounding, transceiver bypass capacitors, and protection-network design directly affect signal integrity and must follow the pin-description and application guidance in the NXP manufacturer datasheet.
Typical uses include LIN-controlled door modules, seat and window controls, climate-control panels, steering-wheel controls, ambient lighting, motor actuators, sensors, and body-control gateways. In these systems, the MC33661PEF handles the physical bus interface and wake detection while a low-power microcontroller or other embedded controller handles protocol functions. The 8-SOIC footprint simplifies board-level integration where a conventional through-hole or larger connector-oriented interface would be unnecessary.
For a robust design, compare the transceiver's specified operating limits, bus timing, output-driver behavior, sleep and wake thresholds, and transceiver version against the vehicle network requirements before release. LIN nodes commonly combine the transceiver with reverse-polarity, transient-voltage, and ESD protection. Those external components should be selected for the harness environment rather than inferred solely from the IC's nominal bus specification.
This product overview organizes the MC33661PEF's package, interface role, wake capability, application fit, sourcing path, and verified replacement considerations into an engineer-oriented reference. It complements the NXP manufacturer datasheet with practical design guidance, explicit compatibility limits, and direct purchasing instructions for current quotation and lead-time requirements.
드롭인 대체품: MC33661PEF — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 제품에는 사용 가능한 드롭인 대체품이 없습니다.
대체품 요청MC33661PEF 사양
| Product Type | LIN bus transceiver with wake-up |
| Bus Category | LINbus |
| Transceiver Configuration | 1/1 half-duplex |
| Wake Capability | Yes |
| 패키지 | 8-SOIC |
| Package Width | 0.154 inch |
| Package Length | 3.90 mm |
| 실장 유형 | Surface mount |
| 핀 수 | 8 |
MC33661PEF 3.90 mm 핀 구성 가이드
MC33661PEF(3.90 mm 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: MC33661PEF.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
MC33661PEF 적합 용도: 6 애플리케이션s: Vehicle Body-Control Modules, Door and Window Control Modules, Climate-Control User Interfaces, Ambient and Exterior Lighting, Seat and Steering-Wheel Controls, Low-Power Sensor Nodes.
Vehicle Body-Control Modules
The MC33661PEF fits distributed body-control modules that communicate over a LIN network and must reduce standby activity. Its half-duplex LIN transceiver provides the physical connection to the single-wire bus, while wake support allows the attached controller to recognize relevant bus activity. In an 8-SOIC package, it supports compact controller boards without requiring a separate physical-layer device. Final design approval should verify supply range, bus thresholds, wake timing, temperature behavior, and automotive qualification against the NXP manufacturer datasheet.
Door and Window Control Modules
Door-lock, window, and mirror modules commonly use LIN for local actuator communication. The MC33661PEF can provide the bus interface between a low-power controller and the vehicle LIN wiring, with wake functionality supporting activity detection when the vehicle is parked. The 8-SOIC footprint is convenient for mixed-technology control boards. Protection from harness transients, reverse polarity, and ESD must be placed near the connector, while the controller determines which bus messages qualify as wake events.
Climate-Control User Interfaces
Climate-control panels and HVAC actuators can use the MC33661PEF to connect an embedded controller to a LIN subnetwork. The half-duplex physical interface supports communication with other nodes while keeping the wiring count low, and wake support can reduce the need for continuous operation. The 8-SOIC package leaves board area for sensing, display control, and power management. Engineers should validate logic levels, wake thresholds, timing, and quiescent behavior against the exact manufacturer specification.
Ambient and Exterior Lighting
Ambient-lighting and exterior-lighting controllers often use LIN to distribute commands and status among multiple lamp nodes. The MC33661PEF supplies the physical-layer interface and wake capability for a controller that needs to detect activity on the network. This helps avoid keeping the complete lighting subsystem active when no relevant command is present. The implementation should account for bus loading, protection requirements, node addressing, and the wake strategy defined by the vehicle system.
Seat and Steering-Wheel Controls
Seat-adjustment and steering-wheel control assemblies can use LIN to link switches and motors to a local controller. The MC33661PEF is appropriate where the assembly requires a compact half-duplex transceiver with wake support. Its 8-SOIC package is practical for dense control boards, while wake detection can support low-power behavior during inactivity. The embedded controller should filter recognized frames and the electronics should use harness-rated protection close to the external connector.
Low-Power Sensor Nodes
A LIN-connected sensor node can use the MC33661PEF to combine bus communication with activity-aware power management. The wake function supports controller strategies that remain asleep until the network presents a relevant condition, while the half-duplex transceiver handles bidirectional bus communication. The compact 8-SOIC package suits space-constrained sensor electronics. Designers should confirm bus voltage tolerance, wake sensitivity, sleep current, and environmental limits in the manufacturer datasheet.
엔지니어링 참조 데이터: MC33661PEF — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 |
|---|---|
| Product Type | LIN bus transceiver with wake-up |
| Bus Category | LINbus |
| Transceiver Configuration | 1/1 half-duplex |
| Package | 8-SOIC |
| Brand | NXP Semiconductors |
| Number of Pins | 8 |
| Package Width | 0.154 inch |
| Package Length | 3.90 mm |
| Wake Capability | Yes |
| Mounting Type | Surface mount |
설계 노트
Do not assign the eight MC33661PEF connections from the package outline alone. Use the pin-description table in the NXP manufacturer datasheet to distinguish supply, ground, LIN, control, wake, and any unused positions. The 8-SOIC footprint establishes mechanical compatibility, but it does not establish electrical or functional compatibility with every related MC3366-family transceiver.
Place the MC33661PEF and its required bypass components close to the associated supply and ground pins, and route the LIN connection toward the protection network without long unprotected stubs. Keep the high-current and transient-prone portions of the harness interface away from sensitive controller traces. Ground-return paths should follow the application guidance in the manufacturer datasheet to minimize susceptibility to EMC events.
Design the node around the MC33661PEF sleep and wake behavior rather than treating wake support as an automatic system power controller. The attached microcontroller must recognize an accepted wake pattern, initialize the LIN interface, and manage the remaining system rails. Verify wake thresholds, timing, and supply behavior against the exact device specification before fixing the production wake strategy.
규정 준수 정보
The MC33661PEF is an automotive-network interface device, but qualification and material-compliance claims require confirmation in the exact NXP manufacturer documentation or product declaration.