MC33742PEPR2 - SBC w/ CAN, 2x LDO, 4 Wake | NXP | QFN-48
부품 번호: MC33742PEPR2 ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $6.12 | $6.12 |
| 10 | $5.48 | $54.80 |
| 100 | $4.71 | $471.00 |
| 500 | $4.05 | $2,025.00 |
| 1,000 | $3.42 | $3,420.00 |
MC33742PEPR2 개요
A System Basis Chip is a category of mixed-signal automotive IC that combines multiple power, communication, and supervisory functions that previously required several discrete components around an automotive microcontroller. Within the broader hierarchy, an SBC belongs to the power management and in-vehicle networking ecosystem alongside transceivers, voltage regulators, and watchdog supervisors. By collapsing these functions into one die, the MC33742 reduces PCB area, simplifies wiring harness interfaces, and helps automakers meet stringent quiescent-current budgets for modules that must remain in a low-power state when the vehicle is parked.
Key features include a fixed 5.0 V/200 mA LDO with current limit and overtemperature pre-warning, a second auxiliary 5.0 V regulator for sensor or communication supplies, four independent wake-up inputs that allow the ECU to exit Sleep mode from local events such as door-switch transitions or sensor edges, a high-speed CAN physical layer capable of 1 Mb/s operation, and a programmable reset generator with 15 ms duration. Internal protection covers thermal shutdown, watchdog timer, and battery voltage monitoring.
The device uses a mixed bipolar-CMOS process with an integrated charge pump and high-side drivers to support the CAN bus recessive/dominant drive symmetry. Its Sleep mode draws a very low quiescent current, allowing body and chassis ECUs to meet the < 100 µA sleep-current targets expected by major OEMs. Compared with discrete solutions, the SBC eliminates inter-IC glue logic and improves ESD/EMC robustness because all sensitive pins are co-located on a controlled silicon substrate.
Typical applications include HVAC control modules, body control modules, instrument clusters, door modules, and seat control units in 12 V automotive systems (5 V/9 V/12 V/15 V/18 V/24 V nominal battery compatibility per the datasheet). The integrated CAN interface makes it a natural fit for powertrain-adjacent and chassis nodes where HS-CAN is the dominant backbone.
For design, attach the exposed thermal pad to a continuous ground copper pour with multiple thermal vias. Place the two decoupling capacitors (one per LDO) directly at their respective output pins to keep load transients within regulation.
This page consolidates distributor pricing, drop-in compatible alternatives, and design guidance not bundled in the original 2004-vintage datasheet, giving procurement engineers and PCB designers a single practical reference.
드롭인 대체품: MC33742PEPR2 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
MC33742EPR2
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MC33742SPEGR2
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MC33742PEG
✅ 드롭인✓ 재고 있음
$4.05 / 개
데이터시트 보기 →MC33742PEP
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
TLE7259-3GE
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MC33742PEPR2 사양
| Product Type | System Basis Chip (SBC) with HS-CAN |
| Manufacturer | NXP Semiconductors (formerly Freescale / Motorola) |
| 패키지 | 48-QFN-EP (7x7 mm) with exposed pad |
| 실장 유형 | Surface Mount |
| CAN Data Rate | 1 Mb/s (High-Speed CAN) |
| Number of CAN Drivers / Receivers | 1 / 1 |
| Integrated LDOs | 2 x 5.0 V / 200 mA low-dropout regulators |
| Wake-Up Inputs | 4 |
| Reset Duration | 15 ms |
| Supply Voltage Range | 5.5 V to 27 V (5V/9V/12V/15V/18V/24V automotive battery compatibility) |
| Operating Modes | Sleep / Standby / Stop / Normal |
| Protection Features | Current limit, overtemperature pre-warning, thermal shutdown, watchdog, battery voltage monitor |
| 동작 온도 | -40C to +125C (automotive AEC-Q100 grade 1) |
| RoHS 상태 | Compliant |
| Lead Free Status | Lead Free |
| MSL 레벨 | 3 (per JEDEC J-STD-020) |
| Primary Applications | Automotive HVAC, body control modules, instrument clusters, door/seat modules |
MC33742PEPR2 48-qfn-ep (7x7 mm) with exposed pad 핀 구성 가이드
MC33742PEPR2(48-qfn-ep (7x7 mm) with exposed pad 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: MC33742PEPR2.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
MC33742PEPR2 적합 용도: 6 애플리케이션s: HVAC Control Module, Body Control Module (BCM), Instrument Cluster, Door Module, Seat Control Unit, Automotive Sensor Node.
HVAC Control Module
The MC33742PEPR2 fits HVAC control modules because its two 5.0 V/200 mA LDOs separately power the MCU and the blower-driver logic, while the integrated HS-CAN transceiver links the HVAC node to the vehicle body network at 1 Mb/s. The four wake inputs detect signals such as door-switch transitions or climate-sensor edges so the module can exit Sleep mode. AEC-Q100 Grade 1 qualification and -40°C/+125°C operation suit under-dash mounting. Placed on the module PCB with the QFN exposed pad soldered to a 1 sq-in copper pour, the SBC supplies a clean rail to the MCU AVDD and handles bus faults automatically. Compared with discrete CAN + LDO + reset designs it reduces BOM by about 4 components, simplifying AEC-Q100 EMI compliance.
추천
Body Control Module (BCM)
In a body control module the MC33742PEPR2 serves as the supply + communication backbone for door locks, lighting drivers and various switch inputs. The HS-CAN interface reaches the vehicle network at 1 Mb/s while the 5 V/200 mA LDOs feed the main MCU and a sensor rail. The four wake inputs handle ignition-key, door and lighting-switch events without waking the MCU - extending battery life. The integrated watchdog and overtemperature pre-warning lower the ECU software burden and ease ASIL B functional-safety analysis. The 48-QFN-EP (7x7) form factor fits compact BCM PCBs and supports external ground-plane thermal relief through the exposed pad, ensuring the part stays within its 125 °C thermal envelope even at 27 V supply and full CAN traffic. This combination is a common choice for premium body-electronics platforms.
추천
Instrument Cluster
The MC33742PEPR2 supplies two isolated 5 V rails to an instrument-cluster MCU and its stepper-motor driver ICs, while the integrated HS-CAN interface carries vehicle-speed, RPM and fuel-level data from the powertrain CAN backbone at 1 Mb/s. The 15 ms reset generator ensures a deterministic MCU startup every crank cycle, critical for cluster boot during cold starts and brief battery dropouts. The four wake inputs let the cluster exit Sleep when the driver opens the door. With an exposed-pad QFN-48 package the SBC handles the wide thermal-load swings of an instrument-cluster environment (sun-load cabin temperatures) while keeping the CAN bus within spec. Compared with stand-alone CAN + LDO designs the SBC saves roughly 30% of board area, a meaningful win for slim cluster housings.
추천
Door Module
Each power-window or power-mirror door module uses the MC33742PEPR2 to consolidate its supply and network functions. The 5 V/200 mA LDOs power the local MCU plus its mirror or window driver; the HS-CAN interface ties into the body-CAN segment; and the four wake inputs handle the door handle touch sensor, child-lock switch and mirror-fold command. AEC-Q100 Grade 1 ratings and -40°C/+125°C operation survive the harsh door-cavity thermal environment. The exposed thermal pad dissipates heat efficiently to the local PCB copper, while the integrated SBC protection (overtemperature pre-warning, watchdog, current limit) lets the door-module software drop functionality rather than latch off on a fault. Long cable runs and high bus noise are no problem because the on-chip transceiver provides the recessive/dominant symmetry the HS-CAN spec demands.
추천
Seat Control Unit
In a power-seat or seat-heating module the MC33742PEPR2 powers the seat logic MCU and switch sensing network with its dual 5 V/200 mA LDOs while routing position and fault data onto the body CAN backbone at 1 Mb/s. Four wake inputs let the seat respond to switch presses from the driver and passenger sides without polling. The SBCs thermal shutdown and current limit protect the seat module against locked-rotor conditions on the seat motor. Its 48-QFN-EP (7x7) package and automotive-grade qualification support under-seat mounting where ambient temperatures climb to 105°C in summer. The integrated watchdog and reset simplify functional-safety documentation for ASIL A SEooC (seat-control) implementations, saving appreciable software effort versus discrete implementations.
추천
Automotive Sensor Node
The MC33742PEPR2 provides the network and power front-end for distributed sensor nodes (parking assist, rain-light, ambient-light, occupant detection). The dual 5 V LDOs feed a small MCU plus the analog sensor front-end, while the HS-CAN interface provides the deterministic network backbone those nodes share with the BCM. Four wake inputs take sensor-flag signals directly so the node can power up in < 1 ms upon stimulus, preserving a low average quiescent current. AEC-Q100 Grade 1 plus the 7x7 mm exposed-pad QFN-48 footprint allow mounting directly behind the bumper or rear-view mirror cavity without thermal runaway. The integrated fault tolerance (overtemperature pre-warning, current limit, watchdog) helps the node survive the harsh under-bumper EMI environment without external protection circuitry.
추천
추천 제품 요약
엔지니어링 참조 데이터: MC33742PEPR2 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MC33742EPR2 | MC33742SPEGR2 | MC33742PEG | MC33742PEP | TLE7259-3GE |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | Infineon |
| Package | 48-QFN-EP (7x7) | 48-QFN-EP (7x7) - same | 48-QFN-EP (7x7) - same | 48-QFN-EP (7x7) - same | 48-QFN-EP (7x7) - same | DSO-8 (CAN only) |
| Function Block | HS-CAN + 2x LDO + 4 wake + reset | Identical (industrial grade) | Identical (alt SPI map) | Identical (tray pack) | Identical (tray pack) | HS-CAN only |
| CAN Data Rate | 1 Mb/s | 1 Mb/s | 1 Mb/s | 1 Mb/s | 1 Mb/s | 1 Mb/s |
| Integrated LDO Outputs | 2 x 5.0 V / 200 mA | 2 x 5.0 V / 200 mA | 2 x 5.0 V / 200 mA | 2 x 5.0 V / 200 mA | 2 x 5.0 V / 200 mA | None (CAN only) |
| Wake-Up Inputs | 4 | 4 | 4 | 4 | 4 | 0 (CAN transceiver only) |
| Supply Voltage Range | 5.5 V to 27 V | 5.5 V to 27 V | 5.5 V to 27 V | 5.5 V to 27 V | 5.5 V to 27 V | 4.75 V to 5.25 V (transceiver only) |
| AEC-Q100 Grade | Grade 1 | Industrial grade | Grade 1 | Grade 1 | Grade 1 | Grade 1 |
| RoHS / Lead Free | Compliant / Yes | Compliant / Yes | Compliant / Yes | Compliant / Yes | Compliant / Yes | Compliant / Yes |
주요 차별점
- Integrates HS-CAN + 2 LDOs + 4 wake + reset in one QFN-48 (vs TJA1043)
- Footprint-compatible variant family (vs MC33910 / MC33911)
- Five automotive battery rails covered in one part (vs Discrete CAN+LDO designs)
설계 노트
Solder the QFN-48 EP exposed pad directly to a 1 sq-in copper pour with a thermal via array (typically 9x 0.3 mm vias) for heat sinking. In worst-case operation (27 V supply, full CAN traffic, both LDOs at 200 mA) power dissipation reaches ~2 W; without the EP copper pour the junction temperature can exceed the 125°C AEC-Q100 Grade-1 limit. Estimated theta_JA on a 1 sq-in 4-layer PCB is ~25 °C/W, giving a ~50°C temperature rise at 2 W dissipation.
Place the two LDO output capacitors (4.7 µF ESR-stable ceramic or tantalum) within 50 mil of the VOUT pins to ensure loop stability and minimize load-transient excursions. Add a 100 nF Y-rated bypass from each LDO output to the local ground near the SBC. Keep the CANH/CANL traces matched in length and characteristic impedance (~120 Ω differential) and route them next to a continuous ground plane for 2 Mb/s-class EMI immunity.
Do not load the MC33742PEPR2's internal 5 V LDO with more than 200 mA per rail - exceeding this trips the internal current limit and resets the MCU. Verify the watchdog feeding period fits within the SPI configuration of the chosen variant (regular vs -S firmware). The wake-up inputs are edge- or level-selectable; misconfiguring the polarity in SPI can prevent the ECU from exiting Sleep, which is the most common field return for this SBC family.
규정 준수 정보
AEC-Q100 Grade 1 qualified per family datasheet; RoHS compliant and lead-free per DigiKey/NXP product listing.
