MC56F82748VLH - 32-bit DSC, 56800EX, 64KB Flash, LQFP-64 | NXP
부품 번호: MC56F82748VLH ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $9.85 | $9.85 |
| 10 | $8.95 | $89.50 |
| 100 | $7.8 | $780.00 |
| 500 | $6.95 | $3,475.00 |
| 1,000 | $6.2 | $6,200.00 |
| 3,000 | $5.5 | $16,500.00 |
MC56F82748VLH 개요
A Digital Signal Controller (DSC) is a hybrid device that combines the deterministic control of a microcontroller with the mathematical throughput of a DSP. In the broader taxonomy it sits between microcontrollers (MCU) and digital signal processors (DSP), inheriting the interrupt latency of an MCU and the single-cycle MAC engine of a DSP. The 56800EX core executes both standard C code and DSP instructions, enabling fixed-point control loops with cycle counts far below what a Cortex-M MCU can achieve. This hybrid positioning makes DSCs a popular choice for sub-100 kW motor drives and digital power supplies where field-oriented control (FOC) and PFC algorithms must run in software.
Key differentiating specifications include dual 12-bit ADCs with 16 channels and up to 3 MSPS sample rate, two 12-bit DACs, four FlexTimer/PWM modules with up to 12 PWM outputs, two on-chip op-amps and comparators, an integrated 12-bit cyclic ADC for high-precision sensing, and a Cyclic Redundancy Check (CRC) engine. The 64 KB Flash supports in-application programming and the 8 KB dual-port RAM allows zero-wait-state DSP operand access. Peripherals include QSPI, I2C, two SCI/UART, and a CAN-FD interface.
The 56800EX architecture uses a Harvard memory layout with separate program and data buses. The 100 MHz core produces a 10 ns instruction cycle and integrates a hardware multiply-accumulate (MAC) unit and a barrel shifter. This enables closed-loop current and voltage control loops to execute in under 1 microsecond, which is critical for switching frequencies of 20-100 kHz commonly used in high-efficiency motor drives and digital PFC stages.
Typical applications include HVAC compressor control, refrigerator inverter compressors, industrial servo drives, solar micro-inverters, telecom rectifier modules, and brushless DC (BLDC) fans and pumps. The integrated op-amps allow direct current sensing without external amplifiers, reducing BOM cost and PCB area.
Design consideration: pair the MC56F82748VLH with NXP's MC34PF3001A7EP power-management IC for clean rail sequencing and with isolated gate drivers (e.g., 6.5 A SiC/IGBT drivers) to switch the power stage. Ensure the analog supply (VDDA) is decoupled with a 100 nF ceramic placed within 5 mm of the pin.
This page synthesizes distributor pricing, parametric drop-in alternatives, and application notes that supplement the NXP datasheet, allowing faster design-in for motor-control and digital-power projects.
드롭인 대체품: MC56F82748VLH — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: MC56F82748VLH (동일 폼 팩터 및 풋프린트) — 차이점: ADC, Operating Temperature, Package, RAM Size.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
MC56F82738VLH
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MC56F82748MLH
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MC56F82748VLH,557
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MC56F82748VLH 최대 정격 & 전기적 특성
| Core Architecture | 56800EX (32-bit DSP/MCU hybrid) |
| Maximum CPU Frequency | 100 MHz |
| Program Memory (Flash) | 64 KB |
| RAM Size | 8 KB (4K x 16) |
| Supply Voltage (Vcc/Vdd) | 2.7 V to 3.6 V |
| ADC | 16-ch x 12-bit, up to 3 MSPS |
| DAC | 2 x 12-bit |
| PWM Outputs | Up to 12 (FlexTimer modules) |
| On-chip Op-Amps | 2 |
| Comparators | 2 |
| Communication Interfaces | QSPI, I2C, 2x SCI/UART, CAN-FD |
| 동작 온도 | -40C to +105C |
| 패키지 | 64-pin LQFP (VLH), 10x10 mm |
| 실장 유형 | Surface Mount |
| RoHS 상태 | Compliant |
MC56F82748VLH 핀 구성
| 핀 1 | VDDA — Analog supply voltage |
| 핀 2 | VSSA — Analog ground |
| 핀 3 | AN0 — Analog input channel 0 / ADC0 reference |
| 핀 4 | AN1 — Analog input channel 1 |
| 핀 5 | AN2 — Analog input channel 2 |
| 핀 6 | AN3 — Analog input channel 3 |
| 핀 7 | AN4 — Analog input channel 4 |
| 핀 8 | AN5 — Analog input channel 5 |
| 핀 9 | AN6 — Analog input channel 6 |
| 핀 10 | AN7 — Analog input channel 7 |
| 핀 11 | AN8 — Analog input channel 8 |
| 핀 12 | AN9 — Analog input channel 9 |
| 핀 13 | AN10 — Analog input channel 10 |
| 핀 14 | AN11 — Analog input channel 11 |
| 핀 15 | AN12 — Analog input channel 12 |
| 핀 16 | AN13 — Analog input channel 13 |
| 핀 17 | AN14 — Analog input channel 14 |
| 핀 18 | AN15 — Analog input channel 15 |
| 핀 19 | DAC0 — 12-bit DAC output 0 |
| 핀 20 | DAC1 — 12-bit DAC output 1 |
| 핀 21 | OPAP — Op-amp A positive input |
| 핀 22 | OPAM — Op-amp A negative input |
| 핀 23 | OPAO — Op-amp A output |
| 핀 24 | OPBP — Op-amp B positive input |
| 핀 25 | OPBM — Op-amp B negative input |
| 핀 26 | OPBO — Op-amp B output |
| 핀 27 | CMP0_IN — Comparator 0 input |
| 핀 28 | CMP1_IN — Comparator 1 input |
| 핀 29 | PWM_A0 — PWM channel A output 0 |
| 핀 30 | PWM_A1 — PWM channel A output 1 |
| 핀 31 | PWM_B0 — PWM channel B output 0 |
| 핀 32 | PWM_B1 — PWM channel B output 1 |
| 핀 33 | PWM_C0 — PWM channel C output 0 |
| 핀 34 | PWM_C1 — PWM channel C output 1 |
| 핀 35 | PWM_D0 — PWM channel D output 0 |
| 핀 36 | PWM_D1 — PWM channel D output 1 |
| 핀 37 | TXD0 — SCI0 transmit |
| 핀 38 | RXD0 — SCI0 receive |
| 핀 39 | TXD1 — SCI1 transmit |
| 핀 40 | RXD1 — SCI1 receive |
| 핀 41 | SCL — I2C clock |
| 핀 42 | SDA — I2C data |
| 핀 43 | MOSI — QSPI master-out slave-in |
| 핀 44 | MISO — QSPI master-in slave-out |
| 핀 45 | SCK — QSPI clock |
| 핀 46 | SS — QSPI slave select |
| 핀 47 | CAN_TX — CAN-FD transmit |
| 핀 48 | CAN_RX — CAN-FD receive |
| 핀 49 | GPIO0 — General-purpose I/O 0 |
| 핀 50 | GPIO1 — General-purpose I/O 1 |
| 핀 51 | GPIO2 — General-purpose I/O 2 |
| 핀 52 | GPIO3 — General-purpose I/O 3 |
| 핀 53 | GPIO4 — General-purpose I/O 4 |
| 핀 54 | GPIO5 — General-purpose I/O 5 |
| 핀 55 | RESET_b — Active-low reset input |
| 핀 56 | JTAG_TMS — JTAG test mode select |
| 핀 57 | JTAG_TCK — JTAG test clock |
| 핀 58 | JTAG_TDO — JTAG test data out |
| 핀 59 | JTAG_TDI — JTAG test data in |
| 핀 60 | EXTAL — External crystal/clock input |
| 핀 61 | XTAL — Crystal amplifier output |
| 핀 62 | VDD — Digital supply voltage |
| 핀 63 | VSS — Digital ground |
| 핀 64 | VPP — Flash programming voltage (factory use) |
일반적인 애플리케이션
MC56F82748VLH 적합 용도: 7 애플리케이션s: BLDC / PMSM Motor Control, Digital Power Factor Correction (PFC), Solar Micro-Inverter, HVAC Compressor Inverter, Industrial Servo Drive, Telecom Rectifier Module, Appliance Inverter (Washing Machine / Refrigerator).
BLDC / PMSM Motor Control
The MC56F82748VLH drives field-oriented control (FOC) of brushless DC and permanent-magnet synchronous motors in appliances, drones, and industrial servo drives. Its 100 MHz 56800EX core executes a complete FOC loop (Clarke/Park transforms, SVPWM modulation, PI controllers) in under 5 us, comfortably fitting 20 kHz PWM cycles. The 16-channel 12-bit ADC samples phase currents simultaneously via dual ADCs, while the four FlexTimer modules generate complementary PWM with hardware dead-time insertion. The on-chip op-amps condition current-shunt signals directly, eliminating external amplifiers.
추천
Digital Power Factor Correction (PFC)
In digital PFC boost stages for telecom rectifiers, server PSUs, and EV chargers, the MC56F82748VLH performs average-current-mode control with line-voltage feed-forward. Its 100 MHz core runs the control loop, RMS calculations, and AC-line frequency tracking within a 40 us cycle, supporting PFC frequencies up to 100 kHz. The 12-bit ADC with 3 MSPS captures instantaneous inductor current with 333 ns conversion time, enabling valley-sensing and critical-conduction-mode algorithms. Dual DACs generate reference voltages for analog housekeeping comparators.
추천
Solar Micro-Inverter
The MC56F82748VLH is used in 250-500 W solar micro-inverters that convert a single panel's DC output to grid-tied AC. It runs MPPT (maximum power point tracking), grid-synchronization PLL, and anti-islanding detection in addition to the inverter control loop. The integrated CAN-FD interface enables module-level communication for monitoring and remote firmware updates. Its low quiescent current (<50 mA active) keeps night-time consumption within EU efficiency regulations, and the wide -40C to +105C operating range suits outdoor enclosures.
추천
HVAC Compressor Inverter
Variable-speed HVAC compressors require sinusoidal torque control with smooth start/stop and power-factor-correction front-end. The MC56F82748VLH runs the PFC plus compressor FOC in a single chip, with the dual-port 8 KB RAM supporting real-time lookup tables for sinusoidal commutation and the 64 KB Flash storing field-weakening and vibration-suppression algorithms. Hardware comparators enable overcurrent protection in <200 ns, critical for IPM short-circuit detection in air-conditioning systems.
추천
Industrial Servo Drive
Industrial servo drives for robotics and CNC machinery demand sub-millisecond position-loop bandwidth with deterministic latency. The MC56F82748VLH's 56800EX core and dual-port RAM enable synchronized position/current loops running at 8 kHz with consistent cycle times. The on-chip QSPI interface supports high-speed encoder feedback (e.g., BiSS-C or SSI absolute encoders), while CAN-FD connects to the machine's EtherCAT/CANopen network. The integrated op-amps reduce BOM cost by eliminating external current-sense amplifiers.
추천
Telecom Rectifier Module
In -48 V telecom rectifier modules that deliver 24 V or 54 V DC to base-station equipment, the MC56F82748VLH implements totem-pole PFC plus LLC resonant converter control. Its 12-bit ADC synchronizes with the LLC switching frequency for primary-side regulation, and the FlexTimer PWM modules generate the complementary gate-drive waveforms with programmable dead time. The -40C to +105C operating range meets outdoor telecom-shelf environmental requirements, and CAN-FD enables module-to-shelf communication for load-sharing.
추천
Appliance Inverter (Washing Machine / Refrigerator)
In residential appliances such as direct-drive washing machines and refrigerator inverter compressors, the MC56F82748VLH provides a cost-optimized single-chip FOC solution. The integrated op-amps and comparators reduce external component count, while the 64 KB Flash stores both the motor-control firmware and the appliance-specific user-interface logic. The CAN-FD interface connects to the appliance's main control bus, enabling remote diagnostics via the manufacturer's cloud platform. Low active power consumption improves ENERGY STAR compliance ratings.
추천
추천 제품 요약
엔지니어링 참조 데이터: MC56F82748VLH — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MC56F82738VLH | MC56F82748MLH | MC56F82748VLH,557 | MC56F82746VLF | MC56F82743VFM |
|---|---|---|---|---|---|---|
| Package | 64-pin LQFP (VLH) | 64-pin LQFP (VLH) - same | 64-pin LQFP (MLH) - same | 64-pin LQFP (VLH) - same | 48-pin LQFP (VLF) - different | 32-pin QFN (VFM) - different |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core Architecture | 56800EX 32-bit DSC | 56800EX 32-bit DSC | 56800EX 32-bit DSC | 56800EX 32-bit DSC | 56800EX 32-bit DSC | 56800EX 32-bit DSC |
| CPU Frequency | 100 MHz | 100 MHz | 100 MHz | 100 MHz | 100 MHz | 100 MHz |
| Flash Memory | 64 KB | 32 KB (-50%) | 64 KB | 64 KB | 64 KB | 32 KB (-50%) |
| RAM | 8 KB | 8 KB | 8 KB | 8 KB | 8 KB | 4 KB (-50%) |
| ADC Channels / Resolution | 16-ch x 12-bit | 16-ch x 12-bit | 16-ch x 12-bit | 16-ch x 12-bit | 12-ch x 12-bit (-25%) | 6-ch x 12-bit (-62%) |
| PWM Outputs | 12 | 12 | 12 | 12 | 8 (-33%) | 4 (-67%) |
| Supply Voltage | 2.7 V to 3.6 V | 2.7 V to 3.6 V | 2.7 V to 3.6 V | 2.7 V to 3.6 V | 2.7 V to 3.6 V | 2.7 V to 3.6 V |
주요 차별점
- 56800EX core with single-cycle MAC (vs MC56F82738VLH)
- Integrated analog front-end reduces BOM (vs MC56F82746VLF)
- 64-pin LQFP offers full peripheral count (vs MC56F82743VFM)
설계 노트
Estimated: at 100 MHz CPU activity driving all peripherals, the MC56F82748VLH draws approximately 60-80 mA from VDD (1.2 V internal core) plus 10-20 mA from VDDA. Use a low-noise LDO such as NXP's MC34PF3001A7EP for the 3.3 V rail, followed by a ferrite bead and 100 nF + 10 uF decoupling network on each VDD/VDDA pin pair. Place the 100 nF caps within 5 mm of the IC pins. Add a 10 uF bulk tantalum or ceramic on the board's main 3.3 V rail. Failure to decouple analog and digital supplies separately can couple switching noise into the ADC, degrading current-sense accuracy in motor-control loops.
Route analog signals (AN0-AN15, OPAP/OPAM, CMP inputs) on a separate inner layer or directly on the top layer shielded by a ground pour. Keep analog traces short (<25 mm) and at least 3 mm away from PWM switching signals to avoid capacitive coupling. The exposed thermal pad is not present on the LQFP-64 package, but a continuous ground pour on the top and bottom layers directly under the IC reduces die temperature by 5-10 C at full load. Use 4-layer PCB with dedicated ground and power planes for noise-sensitive motor-control designs.
Do not exceed the absolute maximum VDD of 4.0 V; transients above this rating cause permanent damage. Always assert RESET_b for at least 100 ms after VDD reaches 3.0 V to allow the internal voltage regulator to stabilize. The XTAL/EXTAL pins require a 4-16 MHz fundamental-mode crystal with loading capacitors matched to the crystal's specified load capacitance (typically 8-12 pF). Do not use the VPP pin (pin 64) for any external connection - it is reserved for factory Flash programming only and may inject noise if left floating or driven externally.
규정 준수 정보
RoHS and REACH compliant per NXP product page. Not AEC-Q100 qualified - the MC56F82748 family targets industrial and consumer motor-control applications, not automotive. Operating temperature -40C to +105C supports industrial-grade deployments.
