MC908AP32CFBE - 8-Bit HC08 MCU 32KB Flash 44-QFP | NXP
부품 번호: MC908AP32CFBE ✗ 단종| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $0 | $0.00 |
| 10 | $0 | $0.00 |
| 100 | $0 | $0.00 |
| 500 | $0 | $0.00 |
| 1,000 | $0 | $0.00 |
MC908AP32CFBE 개요
An 8-bit microcontroller is a single-chip embedded processor that integrates a CPU core, program memory (FLASH), RAM, timers, analog-to-digital conversion, and general-purpose I/O on one die, sitting at the entry level of the microcontroller hierarchy (MCU -> embedded processor -> integrated circuit). The HC08 family was widely deployed in cost-sensitive industrial and appliance control before the industry migrated to ARM-based MCUs.
Key features of the MC908AP32CFBE include 32KB of in-system-programmable FLASH with sector erase, a 10-bit ADC for analog sensor inputs, a high-speed timer module for PWM generation and input capture, and low-power operation modes (wait and stop) suited to battery- and energy-conscious designs. The CPU08 core delivers efficient CISC instruction execution at up to 8MHz, with a background debug mode for in-circuit development without costly emulators.
Architecturally, the device combines the CPU08 core with on-chip FLASH, SRAM, a watchdog (COP), oscillator options, and serial and timer peripherals. The 3.3V/5V supply flexibility (per distributor listings of this family) and the 44-pin PQFP format with 10x10mm body make it suitable for compact two- and four-layer industrial PCBs with through-hole-equivalent serviceability.
Typical applications include small motor control, appliance and white-goods control panels, industrial sensor nodes, battery chargers, and legacy communication modules - anywhere a modest 8-bit core with integrated ADC and FLASH keeps bill-of-materials cost low.
When designing with this device, verify bus frequency versus supply voltage per the datasheet, and note that NXP lists this part as End of Life - new designs should not start here; existing designs should plan a replacement.
This page synthesizes distributor data, lifecycle status, drop-in family alternatives, and practical design notes not consolidated in the manufacturer datasheet.
드롭인 대체품: MC908AP32CFBE — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: MC908AP32CFBE (동일 폼 팩터 및 풋프린트) — 차이점: Core, ADC, Program Memory Size, Supply Voltage, Package.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
MC908AP32ACFBE
✅ 드롭인✓ 재고 있음
$29.663 / 개
데이터시트 보기 →MC908AP16CFBE
✅ 드롭인✓ 재고 있음
$13.6 / 개
데이터시트 보기 →MC908AP64CFBE
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
MC908MR32CBE
✅ 드롭인✓ 재고 있음
$7.25 / 개
데이터시트 보기 →MC908AP32CFBE 최대 정격 & 전기적 특성
| Core Processor | HC08 (CPU08) |
| Core Size | 8-Bit |
| Architecture | CISC |
| 최대 클록 주파수 | 8 MHz |
| Program Memory Size | 32KB (32K x 8) |
| Program Memory Type | FLASH |
| ADC Resolution | 10 bit |
| 공급 전압 | 3.3 V / 5 V (family listing) |
| 패키지 | 44-QFP (10x10 mm) PQFP |
| 실장 유형 | Surface Mount |
| Peripherals | High-speed timer, LVI, COP watchdog, low-power modes |
| Packaging | Tray (family listing: REEL 13" ordering variant available) |
| 수명 주기 상태 | End of Life (per NXP product page) |
MC908AP32CFBE 44-qfp (10x10 mm) pqfp 핀 구성 가이드
MC908AP32CFBE(44-qfp (10x10 mm) pqfp 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: MC908AP32CFBE.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
MC908AP32CFBE 적합 용도: 6 애플리케이션s: Small Motor Control, Appliance and White-Goods Control Panels, Industrial Sensor Nodes, Battery Chargers, Legacy Communication Modules, Security and Access Control Panels.
Small Motor Control
The MC908AP32CFBE fits low-complexity motor control tasks where its high-speed timer provides PWM outputs for drives and its 10-bit ADC reads back shunt or pot feedback. The CPU08 core at 8MHz executes closed-loop control loops for fans, pumps, and small appliance motors with adequate sampling rates, while 32KB FLASH stores commutation tables and fault handling. Integrated COP watchdog improves safety in unattended equipment. Because the part is EOL, use it to sustain existing motor boards and evaluate NXP's current motor-control MCUs for new designs; the architecture's deterministic 8-bit instruction timing still simplifies legacy code certification.
추천
Appliance and White-Goods Control Panels
Appliance control panels need low cost, sensor inputs, and basic user-interface timing - exactly the MC908AP32CFBE's profile. The 10-bit ADC digitizes NTC thermistors and potentiometers; the high-speed timer generates button-scan and buzzer timing; 32KB FLASH holds state machines for wash/bake cycles. Its 3.3V/5V supply flexibility (per family listings) suits mains-derived power supplies, and the 44-QFP (10x10 mm) body offers enough I/O for displays, relays, and switches on a low-layer-count PCB. Wait and stop modes trim standby power. This remains a valid maintenance choice for service parts, though redesigns should target active MCU families with better supply guarantees.
추천
Industrial Sensor Nodes
In industrial sensing, the MC908AP32CFBE digitizes analog transducers through its 10-bit ADC and scales or linearizes readings with firmware in 32KB FLASH. The CPU08's CISC instruction set handles integer math for calibration curves efficiently at 8MHz, and the on-chip LVI and COP watchdog deliver the robustness required in electrically noisy factory environments. The 44-QFP surface-mount package supports compact, conformally coated sensor boards. Legacy sensor product lines already qualified on this device can keep shipping using residual stock; new sensor nodes should select an actively manufactured MCU with richer serial connectivity such as LIN, SPI, or UART with DMA.
추천
Battery Chargers
Battery charger control uses the MC908AP32CFBE's 10-bit ADC to monitor cell voltage and current, while the high-speed timer generates charge PWM with duty-cycle control for CC/CV profiles. 32KB FLASH stores multi-chemistry charging algorithms including taper detection and fault timeout logic, and the CPU08's low-power stop mode suits trickle-standby behavior between charge cycles. The 44-QFP (10x10 mm) footprint allows the controller to sit directly on the power PCB. For maintaining a qualified charger product this part remains serviceable from EOL stock, but new charger platforms should choose MCUs with dedicated high-resolution PWM and integrated comparators to reduce external parts.
추천
Legacy Communication Modules
Older serial communication modules - simple UART-based gateways, keypads, and protocol converters - were commonly built on the HC08AP family. The MC908AP32CFBE's CPU08 core handles serial framing and checksums at 8MHz, its timers generate baud and timeout bases, and 32KB FLASH stores protocol stacks with margin for customization. Its 5V-tolerant I/O family heritage simplifies interfacing with legacy 5V logic levels common in installed industrial equipment. When repairing or extending these modules, the same-footprint AP64 variant adds code space for extra protocol features without PCB changes; all sourcing, however, is constrained by the part's End-of-Life status.
추천
Security and Access Control Panels
Access-control keypads and small alarm panels match the MC908AP32CFBE's capabilities: the 10-bit ADC reads tamper and ambient-light sensors, timers handle keypad debounce, backlighting, and siren timing, and 32KB FLASH stores code tables plus event logs in RAM. The COP watchdog ensures the panel recovers from disturbances, and low-power wait modes suit mains-backed battery operation. The 44-QFP (10x10 mm) package offers sufficient I/O for matrix keypads, LEDs, and lock drivers. Existing qualified designs can be sustained from remaining stock; new security hardware should use active MCUs with hardware encryption for modern credential standards.
추천
추천 제품 요약
엔지니어링 참조 데이터: MC908AP32CFBE — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MC908AP32ACFBE | MC908AP16CFBE | MC908AP64CFBE | MC908MR32CBE |
|---|---|---|---|---|---|
| Package | 44-QFP (10x10 mm) | 44-QFP (10x10 mm) - same | 44-QFP (10x10 mm) - same | 44-QFP (10x10 mm) - same | 44-QFP (10x10 mm) - same |
| Brand | NXP Semiconductors (Freescale) | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core / Max Clock | HC08 CPU08 / 8 MHz | HC08 CPU08 / high-speed oscillator version | HC08 CPU08 / 8 MHz | HC08 CPU08 / 8 MHz | HC08 CPU08 / 8 MHz |
| FLASH Memory | 32KB | 32KB | 16KB | 60KB-class | 32KB class |
| ADC | 10-bit | 10-bit | 10-bit | 10-bit | 10-bit |
| Supply Voltage | 3.3 V / 5 V (family listing) | 3.3 V / 5 V | 3.3 V / 5 V | 3.3 V / 5 V | 3.3 V / 5 V |
| Special Feature | General-purpose HC08AP with 10-bit ADC | High-speed oscillator version (HC08APxA) | Cost-optimized 16KB FLASH | Extended FLASH for larger code | Motor-control oriented HC08 |
| Lifecycle Status | End of Life | End of Life (HC08AP family) | End of Life (HC08AP family) | End of Life (HC08AP family) | End of Life |
주요 차별점
- Twice the memory of the reduced variant (vs MC908AP16CFBE)
- High-speed oscillator variant available (vs MC908AP32ACFBE)
- General-purpose focus vs motor-control specialization (vs MC908MR32CBE)
설계 노트
The MC908AP32CFBE is officially End of Life per the NXP product page, which references a discontinuance and replacement product change notice. Do not start new designs on this device. For existing products, execute a last-time-buy covering remaining service life plus 10-20% spares margin, obtain date-code documentation from any broker, and schedule a firmware-level migration to an active MCU family. Confirm the frequency-versus-supply-voltage derating curve in the family datasheet before running at 8MHz on a 3.3V rail.
The 44-QFP (10x10 mm) package uses 0.8mm-pitch leads; design land patterns per the manufacturer datasheet footprint rather than generic PQFP-44 libraries, since HC08AP pin functions (ADC input multiplexing, oscillator, programming pins) vary by family member. Decouple VDD with 0.1uF ceramic placed within 5mm of each supply pin, plus 4.7-10uF bulk near the part. Route the ADC analog inputs away from oscillator and PWM traces; the 10-bit ADC has no differential input capability, so board-level filtering of analog lines is essential for clean conversions.
Estimated: HC08 MCUs of this class typically draw a few mA active at 8MHz and microamp-level current in stop mode, so total system power is dominated by external loads (LEDs, relays, drivers), not the MCU. Size the 5V or 3.3V rail for peripheral load, verify the low-voltage-inhibit (LVI) threshold matches your supply tolerance so the COP/LVI reset does not nuisance-trigger during brownouts, and add series resistance plus clamp protection on I/O that connect to off-board connectors in industrial environments.
규정 준수 정보
The provided data indicates an environmental quality section exists on the NXP product page but does not state specific RoHS/REACH/lead-free status for this part; consult the NXP Environmental Quality page for MC908AP32CFBE.
