MC908LJ12CFBE - 8-Bit 12KB Flash 52-LQFP MCU | NXP
부품 번호: MC908LJ12CFBE ✗ 단종| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $0 | $0.00 |
| 10 | $0 | $0.00 |
| 100 | $0 | $0.00 |
| 500 | $0 | $0.00 |
| 1,000 | $0 | $0.00 |
MC908LJ12CFBE 개요
An MCU is a semiconductor that integrates a processor core, program memory, data memory, peripherals, and I/O into one device. The MC908LJ12CFBE belongs to the HC08LJ family within the M68HC08 family of low-cost, high-performance 8-bit microcontroller units. Its CPU08 core supports compatibility with the object-code ecosystem associated with M6805, M146805, and M68HC05 families, while its integrated Flash memory supports firmware storage and the security features described by the family documentation.
Key verified features include an 8-bit data bus, 12KB of Flash memory, up to 512 bytes of on-chip RAM according to the retrieved product information, and an internal oscillator capable of supporting operation up to 8MHz. The device is identified in distributor listings as an HC08 CISC microcontroller in a 52-pin LQFP package. The available search data does not provide complete peripheral, electrical, timing, or pin-level details, so those values must be confirmed from the manufacturer datasheet before design release.
Typical design uses for this device include legacy 8-bit control systems, industrial equipment, simple keypad interfaces, sensor conditioning, actuator control, and compact embedded products whose firmware is already based on the HC08 ecosystem. Since the MCU is marked end of life, engineers should verify software-tool support, programmer availability, production quantities, and any substitute MCU requirements rather than assuming that a similarly packaged microcontroller is electrically or software-compatible.
The primary design consideration is lifecycle availability. Before using MC908LJ12CFBE in a new production design, obtain the official NXP datasheet and product-change information, validate the exact 52-LQFP footprint and pin assignments, and confirm that the development toolchain, programmer, and firmware image are still supported. For an existing product, preserve the original footprint and validate the replacement electrically and in production test equipment.
드롭인 대체품: MC908LJ12CFBE — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: MC908LJ12CFBE (동일 폼 팩터 및 풋프린트) — 차이점: Package, Architecture, Program Memory, Series, Product Type.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
MC908JL8MFAE
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
MC908QB8CDWE
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
가격 문의
데이터시트 보기 →MC908AP32ACFBE
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$29.663 / 개
데이터시트 보기 →MC908AB32MFUE
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
가격 문의
데이터시트 보기 →MC908AP16CFBE
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$13.6 / 개
데이터시트 보기 →MC908LJ12CFBE 최대 정격 & 전기적 특성
| Product Type | 8-bit microcontroller unit (MCU) |
| Manufacturer | NXP Semiconductors |
| Processor Core | HC08 |
| Architecture | M68HC08 |
| Instruction Set | CISC |
| 데이터 버스 폭 | 8 bit |
| 최대 클록 주파수 | 8 MHz |
| Program Memory | 12KB Flash |
| Program Memory Organization | 12K x 8 |
| On-Chip RAM | Up to 512 bytes |
| Internal Oscillator | Up to 8 MHz |
| 공급 전압 | 3.3V/5V |
| 패키지 | 52-pin LQFP |
| Package Size | 10 x 10 mm |
| 실장 유형 | Surface Mount |
| Terminal Count | 52 |
| Temperature Grade | Industrial |
| Packaging | Tray |
| 수명 주기 상태 | End of Life |
MC908LJ12CFBE 10 x 10 mm 핀 구성 가이드
MC908LJ12CFBE(10 x 10 mm 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: MC908LJ12CFBE.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
MC908LJ12CFBE 적합 용도: 7 애플리케이션s: Legacy Industrial Control, Sensor Interface and Data Acquisition, Keypad and User Interface Control, Actuator and Motor Sequencing, Simple Communication Gateway, Legacy Consumer Appliance Controller, Programmable Logic and Test Fixture.
Legacy Industrial Control
The MC908LJ12CFBE fits legacy industrial-control boards that already depend on the HC08LJ and CPU08 software ecosystem. Its 8-bit core, 12KB Flash memory, up to 8MHz operation, and 52-pin LQFP package provide a defined platform for reading inputs, controlling outputs, and running timing-based control logic. Because the device is End of Life, an existing machine may continue using qualified inventory, but a new design should verify supply and software support before release. The original schematic, programmer, oscillator configuration, I/O thresholds, and timing behavior must be retained during any replacement project.
추천
Sensor Interface and Data Acquisition
The MC908LJ12CFBE can serve as the controller for a compact sensor interface where an 8-bit MCU must collect digital inputs, sequence measurements, and format data for a downstream controller. The verified 12KB Flash capacity provides a defined firmware region, while operation up to 8MHz supports modest control-loop and communication tasks. The actual suitability depends on the device's complete timer, serial-interface, analog, and I/O specifications, which are not included in the retrieved data. Preserve the original pin assignment and validate signal levels, sampling timing, interrupt latency, and sensor reset behavior on hardware.
추천
Keypad and User Interface Control
The MC908LJ12CFBE is appropriate for a compact keypad, menu, indicator, or access-control interface built around an existing HC08 firmware design. Its 8-bit architecture and 12KB Flash memory are consistent with embedded user-interface state machines, debounce routines, display sequencing, and event handling. The verified package is a 52-pin LQFP, which can support multiple I/O functions, but the complete pin map and electrical limits must be checked in the official datasheet. When replacing the MCU, verify switch debounce timing, indicator drive current, display interface signals, and boot behavior rather than relying on package similarity.
추천
Actuator and Motor Sequencing
The MC908LJ12CFBE can be used in legacy actuator-control systems where firmware handles relay sequencing, step-command generation, interlocks, fault flags, and safety-related state monitoring. The 8MHz maximum operating frequency and 8-bit CPU provide a baseline for deterministic low-complexity sequencing, but timing margins must be calculated from the actual peripherals and instruction cycle data in the manufacturer documentation. The 52-LQFP footprint may help preserve an existing board, yet exact replacement requires checking every power, ground, timer, interrupt, and I/O pin. Production validation should include worst-case actuator timing and fault-response tests.
추천
Simple Communication Gateway
MC908LJ12CFBE may be used in a small legacy gateway that translates between a local sensor or control bus and a host processor. Its HC08LJ architecture and CPU08 compatibility can preserve established object-code assumptions, while 12KB Flash provides room for protocol handling and state management. The retrieved data does not confirm the available serial channels, baud-rate support, DMA behavior, or communication voltage levels, so those parameters must be verified directly from the NXP datasheet. During replacement, validate bus timing, idle levels, interrupt handling, framing, retries, and bootloader compatibility.
추천
Legacy Consumer Appliance Controller
The MC908LJ12CFBE can support an older appliance controller where a compact 8-bit MCU handles button inputs, display states, motor or heater sequencing, and fault reporting. The 3.3V/5V device class and 52-pin LQFP package are compatible with the general architecture of legacy embedded products, although the exact I/O drive and supply requirements are not provided in the verified search data. End-of-life status makes source availability and long-term maintenance more important than headline processor speed. Before migration, verify startup behavior, brownout response, output shutdown states, timing, EMC layout, and the complete manufacturing test sequence.
추천
Programmable Logic and Test Fixture
The MC908LJ12CFBE can be used in a legacy test fixture or programmable logic controller when a stable 8-bit control engine and established HC08 tooling are more valuable than a newer MCU architecture. The 12KB Flash memory supports embedded test sequences, and operation up to 8MHz can handle low-to-moderate I/O scanning tasks. The device's End of Life status requires careful spare-part planning and calibration of test equipment. A replacement candidate must match the 52-pin footprint, programming interface, boot behavior, I/O electrical characteristics, and timing of the original fixture before it is used in production testing.
추천
추천 제품 요약
엔지니어링 참조 데이터: MC908LJ12CFBE — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MC908JL8MFAE | MC908QB8CDWE | MC908AP32ACFBE | MC908AB32MFUE | MC908AP16CFBE |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | Freescale Semiconductor | Freescale Semiconductor | Freescale Semiconductor | Freescale Semiconductor | Freescale Semiconductor |
| Package | 52-pin LQFP | 52-LQFP | 52-LQFP | 52-LQFP | 52-LQFP | 52-LQFP |
주요 차별점
- Known target configuration (vs MC908AP32ACFBE)
- Supplier and lifecycle clarity (vs MC908JL8MFAE)
- Original 52-pin footprint reference (vs MC908QB8CDWE)
설계 노트
Do not treat a 52-pin LQFP candidate as a drop-in replacement solely because its package family matches. Confirm every power and ground connection, oscillator arrangement, programming interface, interrupt routing, port multiplexing, and I/O electrical threshold against the original MC908LJ12CFBE datasheet. The verified data does not provide the complete pinout, so a footprint-only replacement decision is not acceptable.
Before layout release, verify the exact operating-voltage range, absolute maximum ratings, I/O injection limits, output-drive capability, and power-sequencing requirements from the official NXP datasheet. The product listings identify 3.3V/5V operation, but that label does not establish every pin's voltage tolerance. Preserve the original decoupling and grounding arrangement during a replacement, and validate power consumption under worst-case I/O and peripheral activity.
Use the manufacturer package drawing to define the 52-pin LQFP land pattern, pin-1 orientation, solder-mask clearance, and assembly tolerances. Confirm whether the selected package has any exposed thermal or electrical pad before routing. For legacy board reuse, compare the new part's pinout mechanically and electrically before committing to a footprint because a same package designation does not guarantee the same die pad or exposed-pad arrangement.
The MC908LJ12CFBE is identified as End of Life, so procurement risk can outweigh electrical compatibility. Record approved vendor, date code, traceability, incoming-inspection criteria, and spare quantity. If a production transition is required, run boot, programming, interrupt, timer, communication, brownout, and full I/O regression tests on engineering units before approving the change.
규정 준수 정보
The verified distributor and manufacturer search results do not provide extractable RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. The NXP product page identifies the device as End of Life. Compliance claims must be confirmed from current manufacturer documentation or supplier certificates.
