MC908QY1CDTER - 8-Bit HC08 MCU, 1.5KB Flash, 16-TSSOP | NXP
부품 번호: MC908QY1CDTER ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $3.85 | $3.85 |
| 10 | $3.41 | $34.10 |
| 100 | $2.85 | $285.00 |
| 500 | $2.34 | $1,170.00 |
| 1,000 | $1.94 | $1,940.00 |
MC908QY1CDTER 개요
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (ROM/FLASH), data memory (RAM), and a range of peripheral I/O into one package. The HC08 is NXP/Freescale's 8-bit CISC architecture targeted at cost-sensitive embedded applications where deterministic behavior, low power, and compact code density matter more than raw throughput. Within the broader taxonomy, the MC908QY1CDTER is a member of the HC08Q sub-family, sitting below higher-tier 16-bit and 32-bit MCUs but above simple logic controllers in capability.
Key features of the MC908QY1CDTER include 1.5KB of in-system programmable FLASH, 128 bytes of RAM, 14 general-purpose I/O pins, an internal 32 MHz oscillator (with a 5V-tolerant bus interface), and a 5V (4.5V to 5.5V) supply range. The TSSOP-16 footprint provides a slim 4.40 mm body width suitable for space-constrained PCB layouts common in white goods, sensor interfaces, and low-end appliance controllers. As an NXP "Nitron" HC08 device, it is designed for low-power, low-noise analog-friendly embedded designs.
Architecturally, the MC908QY1CDTER uses the M68HC08 enhanced CPU core with BDM (Background Debug Mode) for in-circuit programming and debugging. The device supports a wide supply tolerance to accommodate regulated 5V rails and offers mask-ROM/FLASH variants within the same pinout for OEM cost-down paths. Common peripherals shared across the QY series include timers, an SCI (serial communications interface), and basic input-capture/output-compare channels.
Typical applications are low-cost consumer appliances, battery chargers, industrial sensor signal conditioning front-ends, simple motor-control loop controllers, and replacement of legacy HC05/HC11 designs. The 5V supply tolerance suits automotive subsystems operating at 5V nominal, low-end industrial controllers, and hobby electronics.
When designing with this MCU, ensure the decoupling capacitor is placed as close as possible to the VDD/VSS pair and use the BDM interface for FLASH programming rather than legacy monitor-mode code. The 16-TSSOP package offers a 0.65 mm pin pitch; consider solder joint inspection and stencil aperture tuning during PCB assembly.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
드롭인 대체품: MC908QY1CDTER — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: MC908QY1CDTER (동일 폼 팩터 및 풋프린트) — 차이점: Package, Program Memory Size, Mounting Type, Core Processor, Series.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
MC908QY2ACDTE
✅ 드롭인✓ 재고 있음
$2.55 / 개
데이터시트 보기 →MC908QY4AMPE
✅ 드롭인✓ 재고 있음
$1.84 / 개
데이터시트 보기 →MC68HC908QY1MPE
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$0.55 / 개
데이터시트 보기 →MC908QB4MDTE
✅ 드롭인✓ 재고 있음
$1.55 / 개
데이터시트 보기 →MC908QC16MDTE
✅ 드롭인✓ 재고 있음
$4.2 / 개
데이터시트 보기 →MC9S08QG4CFFE
✅ 드롭인✓ 재고 있음
$1.1 / 개
데이터시트 보기 →MC68HC908QT2MPE
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$1.95 / 개
데이터시트 보기 →MC908QY1CDTER 최대 정격 & 전기적 특성
| Manufacturer | NXP Semiconductors (formerly Freescale) |
| Part Family | HC08Q / M68HC08 |
| Core Architecture | 8-bit HC08 CISC, Von Neumann |
| Program Memory (FLASH) | 1.5 KB (1.5K x 8) |
| RAM | 128 bytes |
| Maximum CPU Clock | 8 MHz (bus) / 32 MHz internal oscillator |
| Supply Voltage Range | 4.5 V to 5.5 V (5 V nominal) |
| I/O Pins | 14 |
| 패키지 | 16-TSSOP (4.40 mm body width) |
| Pin Pitch | 0.65 mm |
| 동작 온도 범위 | -40 C to +85 C (Industrial) |
| 실장 유형 | Surface Mount |
| RoHS 상태 | Compliant (Pb-free terminal finish per Octopart listing) |
| Debug Interface | BDM (Background Debug Mode) |
| 수명 주기 상태 | Active |
MC908QY1CDTER 핀 구성
| 핀 1 | PTA0 — Port A bit 0 / IRQ (interrupt request input) |
| 핀 2 | PTA1 — Port A bit 1 / BDM serial data |
| 핀 3 | PTA2 — Port A bit 2 |
| 핀 4 | PTA3 — Port A bit 3 |
| 핀 5 | VSS — Ground (0 V reference) |
| 핀 6 | VDD — Positive supply (4.5 V to 5.5 V) |
| 핀 7 | OSC1 — Oscillator input (crystal or external clock) |
| 핀 8 | OSC2 — Oscillator output |
| 핀 9 | PTA4 — Port A bit 4 / TCLK (timer clock input) |
| 핀 10 | PTA5 — Port A bit 5 / Reset (open-drain) |
| 핀 11 | PTB0 — Port B bit 0 / SCI TX (transmit) |
| 핀 12 | PTB1 — Port B bit 1 / SCI RX (receive) |
| 핀 13 | PTB2 — Port B bit 2 / TIM channel |
| 핀 14 | PTB3 — Port B bit 3 / TIM channel |
| 핀 15 | PTB4 — Port B bit 4 |
| 핀 16 | PTB5 — Port B bit 5 |
일반적인 애플리케이션
MC908QY1CDTER 적합 용도: 7 애플리케이션s: Consumer Appliance Controller (Washing Machine / Dishwasher Front Panel), Industrial Sensor Signal-Conditioning Front-End, Battery Charger State-Machine Controller, White-Goods LED Status Indicator Driver, Automotive 5 V Subsystem Controller (Non-Safety Domain), Consumer Remote-Control and IR-Transmitter MCU, Industrial Point-of-Sale / Barcode Wand Decoder.
Consumer Appliance Controller (Washing Machine / Dishwasher Front Panel)
The NXP MC908QY1CDTER fits low-cost consumer appliance controllers where its 1.5 KB FLASH holds a stable-state UI routine, 14 I/O pins drive an LED array plus keypad matrix, and the 5 V supply matches legacy analog front-ends. Placed on a button-pad PCB with a regulator-fed 5 V rail, it replaces HC11 designs while keeping the legacy toolchain - the BDM debug pin allows factory firmware calibration. Compared to a CPLD, the HC08 integrates CPU and I/O in one chip, reducing BOM count by 3-4 parts. Its -40 C to +85 C industrial temperature range suits garage-free kitchen environments. The TSSOP-16 saves 30% board area versus SOIC-16, enabling slimmer keypad sub-PCBs.
추천
Industrial Sensor Signal-Conditioning Front-End
Industrial sensor interface boards use the MC908QY1CDTER to read thermocouple / RTD signals, debounce limit switches, and route a UART line to the main PLC. Its 14 I/O pins handle up to seven differential-style switch channels plus a half-duplex serial link to the upstream controller. The 4.5-5.5 V tolerance accommodates 24 V industrial rails stepped down by a small switching regulator. The HC08 CISC core runs deterministic loop timing critical for safety chains - 125 ns bus cycles make precise debounce windows repeatable. Built around an external SPI ADC such as the MCP3201, the design totals $1.30 BOM in volume. Industrial temperature grade (-40 C to +85 C) handles factory floor thermal swings.
추천
Battery Charger State-Machine Controller
Lead-acid or NiMH charger front-ends pair the MC908QY1CDTER with a discrete PWM/MOSFET stage to run a charge-state engine encoded in 1.5 KB of FLASH. The HC08 reads battery voltage via resistor-divider on an I/O pin and toggles charge enable from a control FET. Critical timing (charge cycle period, voltage sampling window) is handled in cheap MCU instructions rather than expensive analog timers. Its 5 V supply and -40 C to +85 C industrial range accommodate garage or outdoor charging stations. Compared to a fully analog charger, the MCU version is firmware-tunable, allowing OEMs to ship one hardware platform for multiple chemistries.
추천
White-Goods LED Status Indicator Driver
Refrigerator door ajar, dishwasher cycle, and dryer status LEDs are cheap to drive using the MC908QY1CDTER's 14 I/O pins as direct current-controlled outputs. The MCU generates blink patterns, plays audio feedback (via tone output PWM), and listens to door-switch inputs - all within a single 16-TSSOP footprint. The 5 V supply accepts a small buck regulator output with headroom margin, while the HC08's near-instantaneous wake-up from STOP mode allows sub-100 uA standby, meeting EU standby power rules. Replacing a dedicated LED-driver IC with the MC908QY1CDTER cuts the bill of materials by $0.30 to $0.50 per board.
추천
Automotive 5 V Subsystem Controller (Non-Safety Domain)
Body controllers for seat adjusters, mirror modules, and accessory multiplex use MC908QY1CDTER-class 8-bit MCUs where determinism and cost outweigh raw throughput. The 5 V supply matches 5 V-rail automotive subsystems, and -40 C to +85 C covers cabin thermal loads (engine bay needs AEC-Q100 Kinetis parts). The HC08 in this design communicates over CAN or LIN bus to a master ECU using a transceiver such as the NXP TJA1050. BDM in-circuit programming speeds OEM factory calibration. Compared to discrete 555-timer-based controllers, the MC908QY1CDTER delivers firmware-tunable behavior without PCB respins.
추천
Consumer Remote-Control and IR-Transmitter MCU
Low-end IR remote controls for TVs, set-top boxes, and AC units traditionally use mask-ROM 4-bit controllers; modern designs swap them for the MC908QY1CDTER which costs about the same, ships in FLASH, and enables rapid OEM customization. The HC08 emits NEC or RC-5 IR protocols through bit-banged GPIOs, debounces the keypad matrix in software, and sleeps at sub-100 uA between key presses. Three AAA cells (4.5 V) sit directly on its supply rails without regulation. The TSSOP-16 footprint fits slim remotes where SOIC-16 would not. Compared to off-the-shelf encoders, this approach is fully programmable.
추천
Industrial Point-of-Sale / Barcode Wand Decoder
Low-cost barcode scanner wands and POS terminals deploy the MC908QY1CDTER to decode pulse streams from photodiode amplifier circuits and drive a UART link to a host display or PC. The HC08's fast interrupt response (under 50 instruction cycles for an IRQ entry) handles real-time edge-to-edge timing needed to discriminate UPC/EAN stripe patterns. The 5 V supply runs directly from a USB-to-5V LDO, and the 16-TSSOP footprint drops into thin, foldable scanner enclosures. Compared to a fully hardware decoder, this MCU version adapts to evolving barcode standards via firmware updates and adds diagnostic logging free of charge.
추천
추천 제품 요약
엔지니어링 참조 데이터: MC908QY1CDTER — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MC908QY2ACDTE | MC908QY4AMPE | MC908QC16MDTE | MC9S08QG4CFFE |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 16-TSSOP (DT) | 16-TSSOP (DT) - same | 16-TSSOP - same | 16-TSSOP - same | 16-TSSOP - same |
| Program Memory (FLASH) | 1.5 KB | 2 KB (+33%) | 4 KB (+167%) | 16 KB (+966%) | 4 KB (+167%) |
| Core Architecture | HC08 8-bit CISC | HC08 8-bit CISC | HC08 8-bit CISC | HC08 8-bit CISC | S08 8-bit (newer core) |
| Supply Voltage Range | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 2.7 V to 5.5 V (wider) |
| Maximum Bus Clock | 8 MHz | 8 MHz | 8 MHz | 8 MHz | 20 MHz |
| ADC Channels | None | Yes (ADC included) | Yes (ADC included) | Yes (ADC included) | Yes (ADC included) |
| Toolchain Support | CodeWarrior HC08 (legacy) | CodeWarrior HC08 | CodeWarrior HC08 | CodeWarrior HC08 | CodeWarrior S08 / Processor Expert |
| Unit Price (1-reel, qty 1000) | $1.94 | $2.10 - $2.40 | $3.50 - $4.00 | $5.20 - $6.00 | $2.80 - $3.20 |
주요 차별점
- Compact TSSOP-16 footprint with full HC08 CPU (vs MC9S08QG4CFFE)
- Optimized entry-level cost with full HC08 instruction set (vs MC908QC16MDTE)
- No ADC exclusion enables clean digital-only partitions (vs MC908QY2ACDTE)
설계 노트
The MC908QY1CDTER requires a regulated 4.5 V to 5.5 V supply. Place a 100 nF decoupling capacitor as close as possible to the VDD/VSS pins (typical < 5 mm trace length) to suppress switching noise from internal oscillators. For multi-rail designs, add a 10 uF tantalum or ceramic bulk capacitor near the part to handle transient current spikes during FLASH programming, where peak current can briefly exceed 30 mA. If a 3.3 V rail is the only source available, step up to 5 V with a small switching regulator before the MCU - the HC08 lacks low-voltage tolerance. Estimated: 30 mA peak at 5 V for BDM erase operations, sustained ~10 mA active.
On the TSSOP-16 board, keep the OSC1/OSC2 traces short and symmetric, shield them from high-current I/O paths, and add a ground guard trace to reduce jitter. The 0.65 mm pin pitch of TSSOP-16 demands PCB solder-mask apertures with maximum 0.45 mm diameter openings to prevent solder bridging; use 0.1 mm pad-to-trace clearance. Star-route VSS from the decoupling capacitor directly to the bypass ground and then to the PCB ground plane; do not daisy-chain VSS across the package. Pin 1 (PTA0/IRQ) is the primary interrupt and should be routed with 5 ns propagation budget.
Ensure the IRA pin (shared with PTA0) is configured correctly - on reset it defaults to IRQ input with internal pull-up disabled. Without external pull-up, a floating IRQ pin can trigger spurious interrupts that disrupt timing-sensitive code. Avoid relying on the 32 MHz internal oscillator for applications requiring high UART accuracy; use the BUSCLK divided output to the SCI block. The VDD rise time during power-up must meet datasheet specification; an RC rise > 100 ms can fail the internal reset circuit. BDM programming requires the BDM pin held low at reset, so design a mini-header that exposes VDD, VSS, BDM, and RESET.
When using the SCI block for UART communication with receivers above 1 Mbps, route the TX/RX traces as a short differential pair with characteristic impedance 50 ohms (typical for USB or RS-232 single-ended signals) and add a 100-ohm series termination resistor near the MCU. The HC08's SCI block generates ~25 ns overshoot on bus transitions; if the cable length exceeds 30 cm, add an external 5 kV-rated ESD diode array such as the NXP PESD5V0L4UG on the line side. Maintain VSS noise below 50 mV peak by pairing each VDD with a high-frequency bypass cap.
규정 준수 정보
RoHS compliant per Octopart listing (Pb-free terminal finish). AEC-Q100 NOT applicable (this is industrial-grade). Reach declaration status not explicit in distributor listings - mark unknown until manufacturer declaration is obtained.
