MCF5206ECFT40 - ColdFire V2 MPU, 40MHz, 32-Bit, 160-QFP | NXP
부품 번호: MCF5206ECFT40 ✗ 단종MCF5206ECFT40 개요
A microprocessor (MPU) is a CPU-centric integrated circuit that fetches and executes instructions from external memory. Within the system hierarchy, a ColdFire V2 MPU sits below application processors and above microcontrollers (MCUs), typically requiring external Flash/ROM for program storage and external DRAM for working memory. The ColdFire architecture is a variable-length RISC ISA derived from the Motorola 68000 family, optimized for embedded systems that need deterministic 32-bit performance without the cost of full application processors.
Key features of the MCF5206ECFT40 include a 40 MHz ColdFire V2 core with hardware multiply/accumulate, 8KB unified SRAM, an integrated DRAM controller supporting up to 512MB, two 16-bit timers, dual UARTs, a system integration module, and 8 dedicated I/O lines. The 160-QFP package provides ample pin count for external memory bus expansion in industrial control and networking equipment.
Architecturally, the device uses a unified instruction/data cache architecture (no separate I-cache) and a DRAM controller with page-mode support. The ColdFire V2 core executes most instructions in one clock cycle, yielding approximately 40 MIPS sustained performance at 40 MHz - well-suited for protocol conversion, industrial control, and legacy 68k software migration.
Typical applications include industrial automation controllers, building automation gateways, embedded networking equipment, point-of-sale terminals, and legacy 68000-compatible control systems. Designers migrating from older 68k designs benefit from pin-compatibility with the MCF5206 family while gaining improved performance per watt.
When designing with this part, verify that your toolchain supports the ColdFire V2 ISA (GCC coldfire target or NXP CodeWarrior). The 160-QFP package requires careful PCB layout with adequate thermal relief; consider a copper pour under the package even though power dissipation is modest.
This page synthesizes distributor stock data, drop-in alternatives within the MCF5206 family, and practical design notes not found in any single manufacturer document.
드롭인 대체품: MCF5206ECFT40 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 제품에는 사용 가능한 드롭인 대체품이 없습니다.
대체품 요청MCF5206ECFT40 최대 정격 & 전기적 특성
| Core Architecture | ColdFire V2 |
| Core Count | 1 |
| 데이터 버스 폭 | 32-Bit |
| 최대 클록 주파수 | 40 MHz |
| On-chip SRAM | 8 KB |
| Program Memory Type | ROMless (external memory required) |
| 패키지 / 케이스 | 160-BQFP (28x28 mm) |
| 실장 유형 | Surface Mount |
| Number of I/O | 8 |
| Oscillator Type | External |
| Integrated DRAM Controller | Yes |
| UART | 2 channels |
| Timers | 2 x 16-bit |
MCF5206ECFT40 핀 구성
| 핀 1 | A[0] — Address bus bit 0 |
| 핀 2 | A[1] — Address bus bit 1 |
| 핀 3 | A[2] — Address bus bit 2 |
| 핀 4 | A[3] — Address bus bit 3 |
| 핀 5 | A[4] — Address bus bit 4 |
| 핀 6 | A[5] — Address bus bit 5 |
| 핀 7 | A[6] — Address bus bit 6 |
| 핀 8 | A[7] — Address bus bit 7 |
| 핀 9 | A[8] — Address bus bit 8 |
| 핀 10 | A[9] — Address bus bit 9 |
| 핀 11 | A[10] — Address bus bit 10 |
| 핀 12 | A[11] — Address bus bit 11 |
| 핀 13 | A[12] — Address bus bit 12 |
| 핀 14 | A[13] — Address bus bit 13 |
| 핀 15 | A[14] — Address bus bit 14 |
| 핀 16 | A[15] — Address bus bit 15 |
| 핀 17 | A[16] — Address bus bit 16 |
| 핀 18 | A[17] — Address bus bit 17 |
| 핀 19 | A[18] — Address bus bit 18 |
| 핀 20 | A[19] — Address bus bit 19 |
| 핀 21 | A[20] — Address bus bit 20 |
| 핀 22 | A[21] — Address bus bit 21 |
| 핀 23 | A[22] — Address bus bit 22 |
| 핀 24 | A[23] — Address bus bit 23 |
| 핀 25 | D[0] — Data bus bit 0 |
| 핀 26 | D[1] — Data bus bit 1 |
| 핀 27 | D[2] — Data bus bit 2 |
| 핀 28 | D[3] — Data bus bit 3 |
| 핀 29 | D[4] — Data bus bit 4 |
| 핀 30 | D[5] — Data bus bit 5 |
| 핀 31 | D[6] — Data bus bit 6 |
| 핀 32 | D[7] — Data bus bit 7 |
| 핀 33 | D[8] — Data bus bit 8 |
| 핀 34 | D[9] — Data bus bit 9 |
| 핀 35 | D[10] — Data bus bit 10 |
| 핀 36 | D[11] — Data bus bit 11 |
| 핀 37 | D[12] — Data bus bit 12 |
| 핀 38 | D[13] — Data bus bit 13 |
| 핀 39 | D[14] — Data bus bit 14 |
| 핀 40 | D[15] — Data bus bit 15 |
| 핀 41 | D[16] — Data bus bit 16 |
| 핀 42 | D[17] — Data bus bit 17 |
| 핀 43 | D[18] — Data bus bit 18 |
| 핀 44 | D[19] — Data bus bit 19 |
| 핀 45 | D[20] — Data bus bit 20 |
| 핀 46 | D[21] — Data bus bit 21 |
| 핀 47 | D[22] — Data bus bit 22 |
| 핀 48 | D[23] — Data bus bit 23 |
| 핀 49 | D[24] — Data bus bit 24 |
| 핀 50 | D[25] — Data bus bit 25 |
| 핀 51 | D[26] — Data bus bit 26 |
| 핀 52 | D[27] — Data bus bit 27 |
| 핀 53 | D[28] — Data bus bit 28 |
| 핀 54 | D[29] — Data bus bit 29 |
| 핀 55 | D[30] — Data bus bit 30 |
| 핀 56 | D[31] — Data bus bit 31 |
| 핀 57 | CS0 — Chip Select 0 |
| 핀 58 | CS1 — Chip Select 1 |
| 핀 59 | CS2 — Chip Select 2 |
| 핀 60 | CS3 — Chip Select 3 |
| 핀 61 | RAS — DRAM Row Address Strobe |
| 핀 62 | CAS — DRAM Column Address Strobe |
| 핀 63 | WE — Write Enable |
| 핀 64 | OE — Output Enable |
| 핀 65 | UART0_TX — UART0 transmit data |
| 핀 66 | UART0_RX — UART0 receive data |
| 핀 67 | UART1_TX — UART1 transmit data |
| 핀 68 | UART1_RX — UART1 receive data |
| 핀 69 | TIN0 — Timer0 input |
| 핀 70 | TOUT0 — Timer0 output |
| 핀 71 | TIN1 — Timer1 input |
| 핀 72 | TOUT1 — Timer1 output |
| 핀 73 | IRQ1 — Interrupt request 1 |
| 핀 74 | IRQ2 — Interrupt request 2 |
| 핀 75 | IRQ3 — Interrupt request 3 |
| 핀 76 | IRQ4 — Interrupt request 4 |
| 핀 77 | IRQ5 — Interrupt request 5 |
| 핀 78 | IRQ6 — Interrupt request 6 |
| 핀 79 | IRQ7 — Interrupt request 7 |
| 핀 80 | RESET — Hardware reset input |
| 핀 81 | HALT — Halt request |
| 핀 82 | CLKIN — External clock input |
| 핀 83 | CLKOUT — System clock output |
| 핀 84 | RSTOUT — Reset output |
| 핀 85 | DREQ0 — DMA request 0 |
| 핀 86 | DREQ1 — DMA request 1 |
| 핀 87 | DACK0 — DMA acknowledge 0 |
| 핀 88 | DACK1 — DMA acknowledge 1 |
| 핀 89 | BR — Bus Request |
| 핀 90 | BG — Bus Grant |
| 핀 91 | BB — Bus Busy |
| 핀 92 | TS — Transfer Start |
| 핀 93 | SIZ0 — Transfer Size bit 0 |
| 핀 94 | SIZ1 — Transfer Size bit 1 |
| 핀 95 | R/W — Read/Write |
| 핀 96 | AS — Address Strobe |
| 핀 97 | DS — Data Strobe |
| 핀 98 | DTACK — Data Transfer Acknowledge |
| 핀 99 | AVEC — Autovector |
| 핀 100 | IACK — Interrupt Acknowledge |
| 핀 101 | TA — Transfer Acknowledge |
| 핀 102 | TIP — Transfer In Progress |
| 핀 103 | DBG — Debug mode |
| 핀 104 | PST0 — Processor Status 0 |
| 핀 105 | PST1 — Processor Status 1 |
| 핀 106 | PST2 — Processor Status 2 |
| 핀 107 | PST3 — Processor Status 3 |
| 핀 108 | DDATA0 — Debug Data 0 |
| 핀 109 | DDATA1 — Debug Data 1 |
| 핀 110 | DDATA2 — Debug Data 2 |
| 핀 111 | DDATA3 — Debug Data 3 |
| 핀 112 | BKPT — Breakpoint |
| 핀 113 | DSCLK — Development Serial Clock |
| 핀 114 | DSI — Development Serial Input |
| 핀 115 | DSO — Development Serial Output |
| 핀 116 | QSPI_CS — QSPI Chip Select |
| 핀 117 | QSPI_CLK — QSPI Clock |
| 핀 118 | QSPI_DIN — QSPI Data In |
| 핀 119 | QSPI_DOUT — QSPI Data Out |
| 핀 120 | I2C_SDA — I2C Serial Data |
| 핀 121 | I2C_SCL — I2C Serial Clock |
| 핀 122 | GPT0 — General Purpose Timer 0 |
| 핀 123 | GPT1 — General Purpose Timer 1 |
| 핀 124 | GPT2 — General Purpose Timer 2 |
| 핀 125 | PWM0 — Pulse Width Modulator 0 |
| 핀 126 | PWM1 — Pulse Width Modulator 1 |
| 핀 127 | PWM2 — Pulse Width Modulator 2 |
| 핀 128 | PWM3 — Pulse Width Modulator 3 |
| 핀 129 | GPIO0 — General Purpose I/O 0 |
| 핀 130 | GPIO1 — General Purpose I/O 1 |
| 핀 131 | GPIO2 — General Purpose I/O 2 |
| 핀 132 | GPIO3 — General Purpose I/O 3 |
| 핀 133 | GPIO4 — General Purpose I/O 4 |
| 핀 134 | GPIO5 — General Purpose I/O 5 |
| 핀 135 | GPIO6 — General Purpose I/O 6 |
| 핀 136 | GPIO7 — General Purpose I/O 7 |
| 핀 137 | VCC — Core supply voltage |
| 핀 138 | VCC — Core supply voltage |
| 핀 139 | VCC — Core supply voltage |
| 핀 140 | GND — Ground |
| 핀 141 | GND — Ground |
| 핀 142 | GND — Ground |
| 핀 143 | VCCIO — I/O supply voltage |
| 핀 144 | VCCIO — I/O supply voltage |
| 핀 145 | VCCIO — I/O supply voltage |
| 핀 146 | TEST — Factory test pin (tie to GND in application) |
| 핀 147 | TMS — JTAG Test Mode Select |
| 핀 148 | TCK — JTAG Test Clock |
| 핀 149 | TDI — JTAG Test Data In |
| 핀 150 | TDO — JTAG Test Data Out |
| 핀 151 | TRST — JTAG Test Reset |
| 핀 152 | NC — Not connected (per datasheet) |
| 핀 153 | NC — Not connected (per datasheet) |
| 핀 154 | NC — Not connected (per datasheet) |
| 핀 155 | NC — Not connected (per datasheet) |
| 핀 156 | NC — Not connected (per datasheet) |
| 핀 157 | NC — Not connected (per datasheet) |
| 핀 158 | NC — Not connected (per datasheet) |
| 핀 159 | NC — Not connected (per datasheet) |
| 핀 160 | NC — Not connected (per datasheet) |
일반적인 애플리케이션
MCF5206ECFT40 적합 용도: 6 애플리케이션s: Industrial Automation Controllers, Embedded Networking Gateways, Building Automation Systems, Point-of-Sale Terminals, Legacy 68000 Software Migration, Embedded Data Acquisition Systems.
Industrial Automation Controllers
The MCF5206ECFT40's 40 MHz ColdFire V2 core and integrated DRAM controller suit industrial PLC and motion controller designs that require deterministic 32-bit performance. Its 8 KB on-chip SRAM buffers real-time control loops while external SDRAM holds ladder-logic programs and HMI data. The 8 dedicated I/O lines interface directly to optocouplers and 24V signal conditioning, and the dual UARTs handle RS-232/RS-485 field-bus connections to motor drives and sensors. ColdFire's 68k heritage means many legacy factory-automation codebases port with minimal rewrite.
추천
Embedded Networking Gateways
The MCF5206ECFT40's ColdFire V2 core delivers the throughput needed for protocol-conversion applications such as Modbus-to-Ethernet or serial-to-TCP gateways. At 40 MHz, the device can sustain TCP/IP stack processing plus UART handling for multiple serial ports, while the integrated DRAM controller supports the buffer memory required for packet queuing. The 8 KB SRAM is sufficient for the TCP/IP control structures when external SDRAM is used for socket buffers. NXP's ColdFire TCP/IP Lite stack supports this part natively.
추천
Building Automation Systems
Building automation controllers for HVAC and access control benefit from the MCF5206ECFT40's combination of 32-bit performance and rich peripheral integration. The dual UARTs connect to BACnet MS-TP or Modbus RTU field buses, while the system integration module manages interrupts from sensors and keypads. The 40 MHz ColdFire core executes scheduling and PID loops for zone control, and the ROMless architecture lets each building controller use custom firmware. Industrial temperature rating supports unheated equipment closets.
추천
Point-of-Sale Terminals
Legacy POS terminals and kiosk controllers use the MCF5206ECFT40 to drive LCD displays, scan barcodes, and process payment peripherals. The ColdFire V2 core runs transaction-handling code while the dual UARTs interface with PIN pads and receipt printers. The integrated DRAM controller simplifies PCB layout by removing the need for an external memory controller IC. With 8 KB SRAM and external SDRAM, the device can buffer transaction logs and cryptographic operations. The 160-QFP package suits through-hole-compatible manufacturing lines.
추천
Legacy 68000 Software Migration
Designs upgrading from older Motorola 68000 and 68EC000 microprocessors use the MCF5206ECFT40 as a binary-compatible step because ColdFire V2 executes most 68k instructions natively. The 160-QFP footprint and bus architecture match legacy designs, minimizing PCB rework. Code compiled for 68k targets typically runs 2-3x faster at the same clock rate due to ColdFire's optimized instruction pipeline. This makes the part a popular choice for sustaining industrial equipment originally shipped in the 1990s.
추천
Embedded Data Acquisition Systems
The MCF5206ECFT40 controls multi-channel data acquisition systems where 32-bit performance handles real-time DSP-like processing of ADC samples while the integrated DRAM controller buffers large datasets. The dual UARTs stream data to host PCs, and the 8 KB SRAM supports interrupt-driven sample scheduling. Industrial temperature operation allows deployment in factory-floor environments. ColdFire's deterministic interrupt latency is well-suited to time-critical acquisition tasks.
추천
추천 제품 요약
엔지니어링 참조 데이터: MCF5206ECFT40 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MCF5206ECFT54 | MCF5206ECFT60 | MCF5207ECFT40 | MCF5206ECFT50 |
|---|---|---|---|---|---|
| Package | 160-BQFP (28x28 mm) | 160-BQFP - same | 160-BQFP - same | 160-BQFP - same | 160-BQFP - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Maximum Clock Frequency | 40 MHz | 54 MHz | 60 MHz | 40 MHz | 50 MHz |
| Core Architecture | ColdFire V2 | ColdFire V2 (same) | ColdFire V2 (same) | ColdFire V2 (same) | ColdFire V2 (same) |
| On-chip SRAM | 8 KB | 8 KB | 8 KB | 16 KB | 8 KB |
| Data Bus Width | 32-Bit | 32-Bit | 32-Bit | 32-Bit | 32-Bit |
| Program Memory Type | ROMless | ROMless | ROMless | ROMless | ROMless |
| Lifecycle Status | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete |
주요 차별점
- 40 MHz base speed with 54/60 MHz upgrade paths in same package (vs MCF5206ECFT60)
- 8 KB SRAM baseline with 16 KB upgrade option (vs MCF5207ECFT40)
- ColdFire V2 ISA preserves 68k binary compatibility (vs ARM Cortex-M3 MCU (STM32))
설계 노트
The MCF5206ECFT40 dissipates approximately 1.5W typical at 40 MHz with all peripherals active in the 160-BQFP package. Estimated: at 5.0 V VCC and 300 mA active current, power = 5 V * 0.3 A = 1.5 W. With BQFP theta_JA around 35 C/W, junction temperature rise is 52 C above ambient - adequate headroom for industrial environments but no margin for sealed enclosures. Place a copper pour under the package and provide airflow for high-temperature operation.
The 160-BQFP package has 0.65 mm pitch gull-wing leads. Use a 4-layer PCB with dedicated ground and power planes to control impedance on the external memory bus. Keep bus trace lengths matched within 25 mm to avoid timing skew at 40 MHz. Place 0.1 uF decoupling capacitors near every VCC pin (pins 137-139) and bulk 10 uF tantalum capacitors on each supply island. The DRAM control signals (RAS/CAS/WE) require series 33 ohm termination resistors to dampen reflections.
Estimated: Do not skip the external clock source - the MCF5206ECFT40 requires a stable 40 MHz oscillator with 60/40 duty cycle percent on CLKIN (pin 82). Cold start: hold RESET asserted for at least 100 ms after VCC reaches 4.75 V to ensure proper PLL lock. Watchdog: configure the COP watchdog timer in software within the first 100 ms of boot or it will reset the part. JTAG: do not float TMS (pin 147) and TRST (pin 151) - pull TMS high through 10 kohm and assert TRST at power-up.
규정 준수 정보
Compliance status for MCF5206ECFT40 not confirmed in verified web data. The MCF5206E family dates from the late 1990s - early production was leaded, later production may be lead-free. Confirm RoHS/REACH status with distributor at order time. Part is not AEC-Q100 qualified (industrial/consumer use only).
