MCP3562T-E/NC - 24-Bit Dual-Channel 153.6 kSPS ADC
부품 번호: MCP3562T-E/NC ✓ 활성MCP3562T-E/NC 개요
An analog-to-digital converter is an integrated circuit that converts continuous voltage signals into numerical values for processing, measurement, or transmission. The MCP3562 belongs to the delta-sigma ADC hierarchy, where a modulator and digital filter extract high-resolution measurements from low-frequency analog inputs. Its dual-channel architecture supports two differential channels or four single-ended channels, making it suitable for bridge sensors, pressure transducers, current sensing, and multi-channel instrumentation.
The MCP3562T-E/NC provides 24-bit resolution, four analog input options, and programmable output data rates up to 153.6 kSPS. Its low-noise architecture is intended for systems in which small sensor signals must be resolved accurately, including industrial process monitoring, medical instrumentation, portable measurement equipment, and laboratory data-acquisition systems.
Its sigma-delta conversion principle trades conversion speed for resolution and noise performance. The two-channel differential configuration can reject common-mode noise present on sensor lines, while the four single-ended inputs simplify multiplexed measurement. Digital filtering and programmable data rates allow the system designer to balance conversion speed, noise bandwidth, and power consumption according to the measurement requirement.
Typical uses include strain-gauge and load-cell front ends, thermocouple interface boards, pressure and flow instrumentation, battery-bank monitoring, and factory automation modules. The 3 V supply also integrates naturally with low-voltage sensor nodes and microcontrollers operating from the same rail.
When laying out the circuit, use short, symmetrical routing for differential inputs and place the analog input and reference connections away from switching nodes and high-current traces. Verify the external reference and input voltage limits against the manufacturer datasheet before applying sensor excitation.
This page organizes the conversion performance, channel options, package details, and pin-compatible Microchip alternatives into a design-focused reference. It also adds practical layout guidance, application fit analysis, and a parameter comparison for engineers evaluating replacements before schematic release.
드롭인 대체품: MCP3562T-E/NC — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: MCP3562T-E/NC (동일 폼 팩터 및 풋프린트) — 차이점: Internal Reference, Resolution.
MCP3562RT-E/NC
✅ 드롭인가격 문의
데이터시트 보기 →MCP3562R-E/NC
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
MCP3562T-E/NC 최대 정격 & 전기적 특성
| Device Type | 24-bit delta-sigma analog-to-digital converter |
| 분해능 | 24 bits |
| Maximum Conversion Rate | 153.6 kSPS |
| Analog Input Configuration | 2 differential inputs or 4 single-ended inputs |
| Number of Channels | 2 differential / 4 single-ended |
| 공급 전압 | 3 V |
| Conversion Architecture | Sigma-delta |
| 패키지 | 20-pin UQFN, 3 x 3 mm |
| 실장 유형 | Surface mount |
| Internal Reference | Not included; external reference required |
| Input Type | Single-ended or differential |
| Programmable Data Rate | Up to 153.6 kSPS |
| RoHS Compliance | unknown |
| Automotive Qualification | not_applicable |
MCP3562T-E/NC 20-pin uqfn, 3 x 3 mm 핀 구성 가이드
MCP3562T-E/NC(20-pin uqfn, 3 x 3 mm 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: MCP3562T-E/NC.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
MCP3562T-E/NC 적합 용도: 6 애플리케이션s: Load Cell and Strain-Gauge Measurement, Industrial Pressure and Process Sensing, Battery and Power-Supply Monitoring, Medical and Laboratory Instrumentation, Environmental and IoT Sensor Nodes, Precision Data-Acquisition Systems.
Load Cell and Strain-Gauge Measurement
The MCP3562T-E/NC fits bridge-based load-cell and strain-gauge front ends because its two differential inputs can carry the small differential signal produced by a Wheatstone bridge while rejecting common-mode voltage on the sensor leads. The 24-bit resolution provides a high numerical scale for millivolt-level bridge outputs, and the programmable rate of up to 153.6 kSPS allows the design to trade conversion speed against the digital filter bandwidth. Use differential routing with closely matched input components and connect the excitation and reference circuitry according to the manufacturer application guidance.
추천
Industrial Pressure and Process Sensing
The MCP3562T-E/NC is suitable for pressure, level, and process-control modules that need more than one low-level analog channel. Two differential channels can monitor independent sensor pairs, while the four single-ended configuration supports a multiplexed control panel with shared analog conditioning. The 24-bit conversion resolution helps preserve small process variations, and the 153.6 kSPS maximum rate supports responsive sampling when the digital filter is set appropriately. Place the analog front end near the connector and isolate it from relay, motor, and switching-converter currents.
추천
Battery and Power-Supply Monitoring
The MCP3562T-E/NC can monitor multiple low-voltage signals in battery-powered instrumentation, including cell voltages, current-sense outputs, and auxiliary supply rails. Its four single-ended inputs reduce the analog channel count needed for a compact monitor, while two differential inputs can measure shunt drops and reject supply-ridge pickup. The 3 V operating supply supports low-power portable systems. Ensure each measured signal remains within the device input limits and account for reference accuracy, because it directly scales the final conversion result.
추천
Medical and Laboratory Instrumentation
The MCP3562T-E/NC is appropriate for low-frequency biomedical instrumentation and laboratory measurement systems where a high-resolution reading is more important than very high sample throughput. Differential inputs help reject offsets and interference on patient-adjacent or bridge-based sensor lines, while selectable single-ended inputs support auxiliary channels such as temperature or gain calibration. The 24-bit output and programmable filtering improve the usable dynamic range of weak signals. Maintain short analog traces, controlled reference routing, and isolation appropriate to the end application.
추천
Environmental and IoT Sensor Nodes
The MCP3562T-E/NC fits compact environmental-monitoring nodes that combine temperature, humidity, gas, or resistive sensor outputs with an external reference. Four single-ended inputs provide flexibility for multiple low-bandwidth sensors, and the two differential channels can support ratiometric or bridge-based sensing. At 153.6 kSPS maximum rate, the converter can oversample slow environmental signals to improve effective noise performance. Use the programmable digital filter and output data rate to balance measurement rate against power use in battery-operated deployments.
추천
Precision Data-Acquisition Systems
The MCP3562T-E/NC serves as the analog front end in precision data-acquisition equipment requiring 24-bit numerical resolution from multiple channels. Its dual differential architecture supports two simultaneous measurement paths, while four single-ended inputs can be routed through an external multiplexer for wider channel counts. The sigma-delta architecture and programmable rates support oversampling and averaging strategies for low-frequency laboratory and test signals. Keep the analog section separated from digital clocks and use shielded or differential routing where the source impedance is high.
추천
엔지니어링 참조 데이터: MCP3562T-E/NC — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MCP3562RT-E/NC | MCP3562R-E/NC |
|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 20-UQFN (3x3 mm) | 20-UQFN (3x3 mm) | 20-UQFN (3x3 mm) |
| Resolution | 24 bits | 24 bits | 24 bits |
| Maximum Conversion Rate | 153.6 kSPS | 153.6 kSPS | 153.6 kSPS |
| Input Configuration | 2 differential / 4 single-ended | 2 differential / 4 single-ended | 2 differential / 4 single-ended |
| Supply Voltage | 3 V | 3 V | 3 V |
| Onboard Voltage Reference | No | Yes | Yes |
| Conversion Architecture | Sigma-delta | Sigma-delta | Sigma-delta |
주요 차별점
- Manufacturer-preferred pin-compatible upgrade path (vs MCP3562RT-E/NC)
- Dual differential and quad single-ended channel flexibility (vs MCP3562R-E/NC)
- High-resolution conversion with selectable throughput (vs MCP3562RT-E/NC)
설계 노트
Route the two differential inputs as closely matched pairs, avoiding switching nodes, relay contacts, and high-current return paths. Keep the input amplifier or sensor interface physically close to the converter, and provide a quiet return path for the reference and analog ground domains. When a sensor source is high impedance, verify settling behavior against the selected output data rate and digital filter configuration.
Treat the external reference as a precision analog supply because reference error scales the measured code. Place the reference bypass network close to the reference pins, use a low-noise reference source, and isolate the reference route from digital return currents. MCP3562T-E/NC requires this external reference arrangement, while MCP3562RT-E/NC provides an onboard reference option for new designs.
Do not assume that equal pin counts guarantee identical conversion behavior during a substitution. The R-version MCP3562 adds an onboard voltage reference and is the manufacturer-preferred option for new designs, so review startup timing, reference configuration, gain calibration, and firmware settings. Confirm the complete ordering code, package drawing, and exposed-pad requirements before approving any replacement.
Select the output data rate and digital-filter bandwidth together. Increasing the conversion rate without accounting for filter settling can reduce effective noise performance and create aliasing in multiplexed single-ended systems. Acquire at an adequate rate relative to the signal bandwidth, and verify conversion timing in the Microchip serial-interface configuration used by the design.
규정 준수 정보
The MCP3562T-E/NC is a 3 V industrial analog-to-digital converter. Use the manufacturer product page and current material-compliance declarations for RoHS, REACH, and halogen-free status.