MCP6022-E/SN - 10 MHz Dual RRIO Op Amp | Microchip
부품 번호: MCP6022-E/SN ✓ 활성MCP6022-E/SN 개요
An operational amplifier is an analog signal-conditioning IC that uses high open-loop gain to amplify the difference between its two inputs. Negative feedback creates a stable closed-loop gain and determines bandwidth, noise gain, output impedance, and common-mode behavior. The MCP6022 belongs to the CMOS operational-amplifier family, combines two independent amplifier channels in one package, and supports rail-to-rail operation, which broadens the usable input and output range within its supply limits.
The two channels provide a 10 MHz gain-bandwidth product, low input offset voltage below 0.5 mV, and low typical operating current of 1.0 mA. Microchip describes low noise of 8.7 nV/√Hz and low total harmonic distortion plus noise of 0.00053%. Rail-to-rail input and output capability allows the amplifier to process signals near either supply rail, while the low operating current supports portable equipment and battery-operated instrumentation.
The MCP6022 family uses Microchip's advanced CMOS process to provide low bias current, high open-loop gain, high speed, and low power consumption. These characteristics suit general-purpose amplification, filtering, buffering, and gain-stage tasks where a compact dual amplifier is preferable to two separate single-channel packages. The -E/SN ordering code identifies the extended-temperature SOIC configuration for industrial and commercial equipment.
Typical uses include microphone preamplification, sensor signal conditioning, audio and communication channels, active filters, and low-voltage data acquisition. In a portable sensor interface, the MCP6022 can buffer a high-impedance source before an ADC. In an audio design, one channel can provide gain while the other drives a monitoring buffer. Rail-to-rail swing is especially useful when the signal must remain within a narrow low-voltage range.
Design the circuit with adequate input common-mode voltage, output headroom, stable feedback networks, and decoupling capacitors close to the supply pins. Avoid placing the feedback network far from the amplifier because parasitic capacitance can reduce bandwidth and encourage oscillation. Select external resistor and capacitor values against the gain-bandwidth product, and verify operation across the full supply range and temperature range of the assembled system.
This page combines the manufacturer's operating characteristics, package and pin information, drop-in comparison guidance, and practical circuit-design notes. These engineering references help distinguish the MCP6022-E/SN from lower-speed, higher-current, or different-pinout amplifiers before it is approved for a PCB design.
드롭인 대체품: MCP6022-E/SN — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: MCP6022-E/SN (동일 폼 팩터 및 풋프린트) — 차이점: Package, Amplifier Type, Input Offset Voltage, Number of Channels, Output Swing.
MCP6022-I/SN
✅ 드롭인가격 문의
데이터시트 보기 →MCP6022T-E/SNVAO
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MCP6022T-I/SNVAO
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MCP6002-I/SN
✅ 드롭인가격 문의
데이터시트 보기 →MCP6002-E/SN
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MCP6022-E/SNVAO
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MCP6022-E/SN 최대 정격 & 전기적 특성
| Number of Amplifier Channels | 2 channels |
| Gain-Bandwidth Product | 10 MHz |
| Typical Operating Current | 1.0 mA |
| Input Offset Voltage | Less than 0.5 mV |
| Supply Voltage Range | 2.5 V to 5.5 V |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Input Noise Density | 8.7 nV/√Hz |
| Total Harmonic Distortion Plus Noise | 0.00053% |
| 핀 수 | 8 pins |
| 패키지 | SOIC-8, 4.9 mm x 3.9 mm |
| Lead Pitch | 1.27 mm |
| 실장 유형 | Surface mount |
MCP6022-E/SN 핀 구성
| 핀 1 | OUTA — Operational amplifier A output |
| 핀 2 | INA− — Inverting input for operational amplifier A |
| 핀 3 | INA+ — Non-inverting input for operational amplifier A |
| 핀 4 | V− — Negative supply voltage |
| 핀 5 | INB+ — Non-inverting input for operational amplifier B |
| 핀 6 | INB− — Inverting input for operational amplifier B |
| 핀 7 | OUTB — Operational amplifier B output |
| 핀 8 | V+ — Positive supply voltage |
일반적인 애플리케이션
MCP6022-E/SN 적합 용도: 6 애플리케이션s: Portable Sensor Signal Conditioning, Audio Preamplifier and Monitoring Buffer, Low-Voltage Active Filtering, Battery-Powered Instrumentation, Communications Interface Buffering, Data Acquisition Front End.
Portable Sensor Signal Conditioning
The MCP6022-E/SN fits portable sensor interfaces that operate from 2.5 V to 5.5 V and require two independent amplifier channels. Its 10 MHz gain-bandwidth product is comfortably above the bandwidth normally required for temperature, pressure, or slow chemical sensors, while the 1.0 mA typical operating current helps limit battery drain. Place the amplifier close to the sensor to minimize interference pickup, use short feedback paths, and bypass the supply pins locally. The rail-to-rail input and output characteristics allow useful signal levels even when the sensor output lies near either supply rail. In a two-stage design, one channel can amplify the sensor signal and the other can buffer the result for an ADC.
추천
Audio Preamplifier and Monitoring Buffer
The MCP6022-E/SN provides two channels for compact audio preamplification or active monitoring. Its 8.7 nV/√Hz input-noise density, low offset voltage below 0.5 mV, and 0.00053% THD+N specification make it suitable for clean, low-voltage audio gain stages. One channel can provide the principal gain path while the other can buffer an output for monitoring or feed another converter. The 10 MHz gain-bandwidth product supports moderate audio-bandwidth closed-loop gains with ample margin. Keep the input return path short, use balanced resistor values where practical, and confirm that the output remains within the required headroom at peak signal levels.
추천
Low-Voltage Active Filtering
The MCP6022-E/SN is appropriate for first- and second-order active filters built around a 2.5 V to 5.5 V supply. Its 10 MHz gain-bandwidth product allows useful closed-loop bandwidth at several common closed-loop gains and reduces the likelihood that the amplifier becomes the limiting element in precision filter designs. Two amplifiers in one SOIC-8 package can implement a second-order active filter or separate two filter channels. Component tolerances and the amplifier's actual gain-bandwidth response determine the realized cutoff and phase behavior. Verify stability, common-mode range, and output swing across temperature rather than relying only on nominal filter equations.
추천
Battery-Powered Instrumentation
The MCP6022-E/SN suits low-power instrumentation that must balance signal bandwidth, common-mode range, and supply efficiency. A typical operating current of 1.0 mA allows both amplifier channels to operate from a compact battery-regulated rail, while rail-to-rail inputs help preserve measurement span in a 3.3 V or 5 V system. The amplifier can condition a bridge, transducer, or resistive sensor before digitization. For best results, use a low-reference-voltage ADC, maintain common ground paths, and include power-supply filtering that does not add excessive board area. Because input bias current, offset, and temperature drift affect high-impedance sources, those parameters should be checked against the sensor impedance.
추천
Communications Interface Buffering
The MCP6022-E/SN can provide input buffering, gain, and level conditioning in low-voltage communications equipment. Its 10 MHz gain-bandwidth product is suitable for moderate-speed analog interfaces rather than high-rate protocol equalization, while rail-to-rail operation offers flexibility in systems using a 2.5 V, 3.3 V, or 5 V rail. The two channels can support transmit and receive paths when their bandwidth requirements are similar. Keep sensitive input nodes compact, place bypass capacitors beside the supply pins, and route high-impedance nodes away from switching nodes. Validate the closed-loop response and available output drive against the actual line impedance and channel bandwidth before production release.
추천
Data Acquisition Front End
The MCP6022-E/SN is useful as an analog front end ahead of an ADC in compact data-acquisition systems. The dual configuration can amplify one channel and buffer another, or provide differential excitation and single-ended sensing when the circuit topology requires it. A 10 MHz gain-bandwidth product offers margin for moderately fast sensor signals, while the 1.0 mA typical operating current suits portable equipment. The amplifier cannot compensate for an out-of-range common-mode input or inadequate output range, so verify those constraints against the sensor and converter. For high-impedance sources, account for bias-current error and leakage, and use guarding or a lower-impedance sensor when necessary.
추천
추천 제품 요약
엔지니어링 참조 데이터: MCP6022-E/SN — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MCP6022-I/SN | MCP6022T-E/SNVAO | MCP6022T-I/SNVAO | MCP6002-I/SN | MCP6002-E/SN |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 |
| Amplifier Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Ordering-Code Family | MCP6022-E/SN extended-temperature suffix | MCP6022 family with -I/SN suffix | MCP6022T family with -E/SNVAO suffix | MCP6022T family with -I/SNVAO suffix | MCP6002 family with -I/SN suffix | MCP6002 family with -E/SN suffix |
주요 차별점
- Provides higher bandwidth than the MCP6002 alternatives (vs MCP6002-E/SN)
- Combines two rail-to-rail amplifier channels in one SOIC-8 (vs MCP6022-I/SN)
- Supports low-voltage operation with limited supply current (vs MCP6002-I/SN)
- Delivers low noise for sensitive analog signal paths (vs MCP6022-E/SNVAO)
설계 노트
Place the input, output, and feedback components close to their associated SOIC-8 pins. Keep the non-inverting input path short, avoid routing high-impedance inputs beside digital or switching traces, and connect the decoupling capacitor directly between pins 8 and 4. A short ground return from pin 4 helps keep supply noise and output-current return paths out of the sensitive input node.
Check closed-loop stability across every intended gain, including gains approaching the upper limit of the 10 MHz gain-bandwidth product. Use feedback resistors that avoid excessively high values, because parasitic input and output capacitance combined with large resistance can create peaking or oscillation. Add an isolation resistor between the amplifier output and a downstream capacitive load when the load is not directly specified by the manufacturer.
Rail-to-rail operation does not remove the need to observe input and output limits. Maintain the supply voltage within 2.5 V to 5.5 V, verify common-mode and output-swing behavior at the lowest supply voltage and highest temperature, and account for input bias-current error when driving a high-impedance sensor. Also verify that any substitute uses the same SOIC-8 pinout and equivalent noise, offset, bandwidth, and temperature limits.
For high-impedance sensor inputs, use a guarded or tightly routed signal trace and minimize leakage from board contamination and flux residue. Place low-noise input circuitry away from regulators, switching converters, and high-current return paths. The MCP6022's 1.0 mA typical operating current helps power budget, but it does not prevent external noise from coupling into a high-impedance node.
규정 준수 정보
The manufacturer product material identifies the MCP6022 family but does not explicitly state component-level RoHS, REACH, lead-free, halogen-free, or conflict-minerals status.