MCP602T-E/ST - Dual 2.8MHz RRIO Op Amp | Microchip
부품 번호: MCP602T-E/ST ✓ 활성MCP602T-E/ST 개요
An operational amplifier, or op amp, is a voltage-controlled differential amplifier that uses feedback to shape gain, filtering, buffering, and signal conversion. The MCP602 family combines two amplifiers in one package, placing it in the hierarchy of dual CMOS op amps, analog amplifiers, and general-purpose analog semiconductors. Its low operating current supports battery-powered equipment, while the rail-to-rail output stage improves dynamic range in low-voltage systems.
Key characteristics include a 2.8 MHz gain-bandwidth product, less than 2 mV input offset voltage, and 230 uA typical operating current. The 2.7 V to 6.0 V single-supply range accommodates common 3.3 V and 5 V rails. Rail-to-rail output swing allows the output to approach the supply limits more closely than a conventional fixed-output amplifier, although designers should account for the output limits at the selected voltage and load.
Microchip's advanced CMOS process supports low bias current, high open-loop gain, and low-power operation in the MCP602 family. Each amplifier is independently usable, allowing the two channels to perform different functions such as signal amplification and active filtering. Noise-gain and feedback networks determine the closed-loop bandwidth, while input bias current, common-mode range, output swing, and stability constrain the practical application.
Typical uses include portable sensor interfaces, low-speed data acquisition, analog filtering, buffer stages, and general-purpose embedded signal conditioning. The dual configuration is especially useful when a design needs matched channel functions, such as differential sensing or cascaded filtering. A 5 V application still requires verification of input and output ranges at the actual signal amplitude and load.
The primary design consideration is power-rail headroom. Input signals must remain inside the amplifier's common-mode range, and outputs must remain within the usable output swing. Place bypass capacitors close to the supply pins, use short feedback paths, and avoid capacitive loading that can reduce stability. Confirm the gain-bandwidth margin for the selected closed-loop gain.
This product overview combines the manufacturer device specifications, package identification, cross-reference options, application guidance, and practical design notes needed to evaluate the MCP602T-E/ST for low-voltage analog systems.
드롭인 대체품: MCP602T-E/ST — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: MCP602T-E/ST (동일 폼 팩터 및 풋프린트) — 차이점: Package, Gain-Bandwidth Product, Package Width, Amplifier Type, Input Offset Voltage.
MCP602T-I/ST
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MCP602-E/ST
✅ 드롭인가격 문의
데이터시트 보기 →MCP602-I/ST
✅ 드롭인가격 문의
데이터시트 보기 →MCP6022-E/ST
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MCP6024-E/ST
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MCP602T-E/ST 최대 정격 & 전기적 특성
| Amplifier Type | General-purpose CMOS operational amplifier |
| Number of Channels | 2 channels |
| Gain-Bandwidth Product | 2.8 MHz |
| Typical Operating Current | 230 uA |
| Input Offset Voltage | <2 mV |
| Supply Voltage Range | 2.7 V to 6.0 V |
| Output Swing | Rail-to-rail |
| 패키지 | 8-pin TSSOP |
| Package Width | 4.4 mm |
| 실장 유형 | Surface mount |
| Process Technology | Advanced CMOS |
MCP602T-E/ST 핀 구성
| 핀 1 | OUTA — Amplifier A output |
| 핀 2 | IN A- — Inverting input for amplifier A |
| 핀 3 | IN A+ — Non-inverting input for amplifier A |
| 핀 4 | V- — Negative supply or ground connection |
| 핀 5 | IN B+ — Non-inverting input for amplifier B |
| 핀 6 | IN B- — Inverting input for amplifier B |
| 핀 7 | OUTB — Amplifier B output |
| 핀 8 | V+ — Positive supply connection |
일반적인 애플리케이션
MCP602T-E/ST 적합 용도: 6 애플리케이션s: Battery-Powered Sensor Signal Conditioning, Portable Medical Sensor Interface, Industrial Low-Level Signal Amplification, Active Filters and Audio-Style Buffers, Portable Data-Acquisition Front End, IoT Sensor Node Conditioning.
Battery-Powered Sensor Signal Conditioning
The MCP602T-E/ST fits battery-powered sensor front ends because its 2.7 V minimum supply and 230 uA typical operating current suit low-energy systems. Place one channel in a non-inverting configuration and the other in an inverting configuration when the sensor output requires referenced amplification. The 2.8 MHz gain-bandwidth product provides more bandwidth than many low-frequency sensors require, while the less-than-2 mV input offset limits signal error. Confirm the sensor output range against the amplifier's common-mode limits and check whether the total battery load is dominated by sensor excitation or external circuitry.
추천
Portable Medical Sensor Interface
The MCP602T-E/ST can condition low-level signals from portable medical sensors where low power, small package size, and rail-to-rail output are useful. Its 230 uA typical operating current limits amplifier overhead, and the less-than-2 mV input offset reduces error around small sensor outputs. Two independent channels can amplify a differential sensor signal or provide gain and buffering in separate stages. The 2.7 V to 6.0 V supply range supports compact battery rails, although safety-critical designs require the appropriate medical qualification, protection, isolation, and validation beyond the amplifier's core electrical specifications.
추천
Industrial Low-Level Signal Amplification
The MCP602T-E/ST is suitable for industrial measurement circuits that amplify low-level sensor or transducer signals without requiring a high-speed amplifier. The less-than-2 mV input offset and 2.8 MHz gain-bandwidth product support precision gain stages around 1 kHz to tens of kilohertz, depending on closed-loop gain. Its dual channel permits one stage for excitation or filtering and another for output buffering. The 230 uA typical operating current benefits low-power acquisition nodes, but grounding, input protection, supply filtering, and calibration determine overall measurement accuracy in industrial environments.
추천
Active Filters and Audio-Style Buffers
The MCP602T-E/ST can implement active low-pass, high-pass, or notch-filter stages where low power and rail-to-rail output are more important than very high bandwidth. The 2.8 MHz gain-bandwidth product supports moderate-frequency filters, and the dual package lets one channel perform filtering while the other buffers the source or output. Use low-noise resistor and capacitor selections when component values become large relative to the 230 uA bias-current contribution. Verify the output swing at the worst-case load and confirm stability with the selected feedback network and any capacitive input or output loading.
추천
Portable Data-Acquisition Front End
The MCP602T-E/ST fits a compact data-acquisition front end that must amplify sensor outputs before conversion. Its 2.8 MHz gain-bandwidth product preserves signal amplitude across moderate-frequency channels, while the 2.7 V to 6.0 V range supports common portable supply rails. Two channels allow simultaneous gain and driver functions without increasing the number of amplifier packages. Design the input network to avoid excessive capacitance, keep feedback traces short, and account for the less-than-2 mV offset when calculating accuracy. Rail-to-rail output improves range utilization but does not eliminate output-swing restrictions.
추천
IoT Sensor Node Conditioning
The MCP602T-E/ST is appropriate for IoT sensor nodes that condition analog measurements before an embedded ADC or radio interface. Its 230 uA typical operating current and single 2.7 V to 6.0 V supply simplify power budgeting in compact devices. The two amplifier channels can implement a gain stage and an active filter, while the 2.8 MHz gain-bandwidth product is sufficient for many slow environmental sensors. Keep the analog path physically separated from switching and radio circuitry, bypass the supply at the pins, and verify the common-mode range at startup because sensor outputs may move close to either rail.
추천
추천 제품 요약
엔지니어링 참조 데이터: MCP602T-E/ST — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MCP602T-I/ST | MCP602-E/ST | MCP602-I/ST | MCP6022-E/ST | MCP6024-E/ST |
|---|---|---|---|---|---|---|
| Package | 8-pin TSSOP | 8-pin TSSOP | 8-pin TSSOP | 8-pin TSSOP | 8-pin TSSOP | 8-pin TSSOP |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Number of Channels | 2 | 2 | 2 | 2 | 2 | 2 |
| Output Swing | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Ordering Suffix | T-E/ST | T-I/ST | -E/ST | -I/ST | 2-E/ST | 4-E/ST |
주요 차별점
- Low operating current for a 2.8 MHz dual amplifier (vs MCP6022-E/ST)
- Two rail-to-rail amplifiers in one 8-pin TSSOP (vs MCP6024-E/ST)
- Matched core specifications within the MCP602 family (vs MCP602T-I/ST)
설계 노트
The MCP602 family operates from 2.7 V to 6.0 V with 230 uA typical operating current. Place the supply bypass capacitor close to pin 8 and connect pin 4 to the circuit ground plane with a short return path. This is especially important in portable and IoT designs because long supply traces add resistance and can couple noise into the amplifier inputs. Confirm total current under the maximum expected load because the 230 uA figure represents typical amplifier operating current.
Keep the two amplifier inputs, feedback components, and output routes compact. Place feedback resistors close to the relevant inverting-input pins to minimize parasitic capacitance, which can affect stability and bandwidth. The MCP602's 2.8 MHz gain-bandwidth product provides substantial margin in many low-frequency circuits, but high closed-loop gain or capacitive loading still requires a stability check.
Do not assume rail-to-rail output means the output can reach either supply rail under every load. Check the output-voltage limits, input common-mode range, output-current capability, and temperature range in the manufacturer datasheet. Keep the two channels electrically independent unless the circuit intentionally ties them together, and verify that each selected suffix preserves the required temperature grade and pin configuration.
규정 준수 정보
Compliance status must be confirmed for the exact MCP602T-E/ST ordering code using the manufacturer's product page or declaration documentation.