MCP6034-E/SL - 10kHz Low-Power Quad Op Amp | Microchip
부품 번호: MCP6034-E/SL ✓ 활성MCP6034-E/SL 개요
An operational amplifier, or op amp, is an analog signal-conditioning IC used to amplify, buffer, filter, compare, or control voltages. The MCP6034 belongs to the broader precision operational amplifier family and combines low power consumption, high open-loop gain, low bias current, and rail-to-rail input and output operation. These characteristics place it between general-purpose amplification and precision low-energy acquisition systems.
Key features include four amplifiers in one package, operation from a single supply as low as 1.8 V, a typical operating current of 900 nA per amplifier, and rail-to-rail input and output swing. The 10 kHz gain-bandwidth product is sufficient for low-frequency sensor conditioning, battery monitoring, and portable measurement systems. Low input bias current reduces errors when measuring high-impedance sources.
Microchip's advanced CMOS process supports low bias current and low quiescent consumption while retaining useful open-loop gain. Rail-to-rail input capability increases the usable common-mode range, while rail-to-rail output swing improves dynamic range in low-voltage systems. Because the amplifiers operate from one supply, they are well suited to systems where a negative rail is unavailable or undesirable.
Typical applications include portable instrumentation, low-current sensor interfaces, battery-powered monitoring, industrial process measurement, and precision current sensing. The quad configuration also reduces board area and can support independent filtering, buffering, or gain stages within one compact package.
When designing with the MCP6034-E/SL, verify the maximum input common-mode range, output swing, and capacitive-load behavior under the intended load conditions. Input and output stability should be evaluated with realistic source impedance, sensor capacitance, and PCB leakage rather than relying only on nominal open-loop behavior.
This page combines technical specifications, same-package replacement options, application guidance, and practical PCB design considerations to help engineers evaluate the MCP6034-E/SL for precision, low-power analog designs.
드롭인 대체품: MCP6034-E/SL — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: MCP6034-E/SL (동일 폼 팩터 및 풋프린트) — 차이점: Output Swing, Package.
MCP6034-E/ST
✅ 드롭인가격 문의
데이터시트 보기 →MCP6034-I/SL
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
MCP6034-I/ST
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
MCP6034-E/SL 최대 정격 & 전기적 특성
| Number of Amplifiers | 4 channels |
| Amplifier Type | General-purpose operational amplifier |
| Gain-Bandwidth Product | 10 kHz |
| Typical Operating Current | 900 nA per amplifier |
| Input Offset Voltage | Less than 150 uV |
| Minimum Single-Supply Voltage | 1.8 V |
| Output Swing | Rail-to-rail |
| Input Type | Rail-to-rail |
| 패키지 | 14-pin SOIC, 3.90 mm width |
| 실장 유형 | Surface mount |
| Process Technology | Advanced CMOS |
MCP6034-E/SL 14-pin soic, 3.90 mm width 핀 구성 가이드
MCP6034-E/SL(14-pin soic, 3.90 mm width 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: MCP6034-E/SL.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
MCP6034-E/SL 적합 용도: 6 애플리케이션s: Portable Sensor Signal Conditioning, Battery-Powered Monitoring, Industrial Process Measurement, Precision Current Sensing, Low-Voltage Audio and Control Buffers, Data Acquisition Interface.
Portable Sensor Signal Conditioning
The MCP6034-E/SL fits portable sensor interfaces that require several channels of low-frequency amplification without adding a negative supply. Its 1.8 V minimum single-supply operation, 900 nA typical current per amplifier, and rail-to-rail input and output behavior support low-energy measurement systems. Four channels can condition bridge, resistive, or buffered sensor signals while reducing package count. The 10 kHz gain-bandwidth product is appropriate for slow sensor signals, although source impedance, input capacitance, noise, and accuracy must still be evaluated for the selected gain.
추천
Battery-Powered Monitoring
The MCP6034-E/SL is appropriate for battery-powered voltage and current monitoring where four amplifiers can operate from one low-voltage rail. Its 900 nA typical operating current per amplifier reduces standby burden, while operation from 1.8 V supports cells and regulated low-voltage rails. Rail-to-rail output swing improves usable signal range near the supply limits. Because the gain-bandwidth product is only 10 kHz, the device is best for slow measurements rather than fast transients, and input offset error must be included in the overall measurement budget.
추천
Industrial Process Measurement
The MCP6034-E/SL can support low-frequency industrial process signals when the design requires several precision amplifier channels in a 14-pin package. Its input offset voltage below 150 uV, high open-loop gain, and rail-to-rail input operation help preserve small signals derived from resistive sensors. The 900 nA typical current per amplifier is valuable in distributed, power-constrained measurement nodes. Engineers should verify input bias current, noise, common-mode range, and output-drive limits against the selected sensor and front-end network.
추천
Precision Current Sensing
The MCP6034-E/SL can amplify low-level shunt or current-transformer signals in compact instrumentation when four channels share a common low-power architecture. The specified offset voltage below 150 uV limits input-referred error, and the 10 kHz gain-bandwidth product is suitable for many slowly changing current measurements. Single-supply operation simplifies systems without a negative rail. Stability and common-mode behavior must be checked against shunt impedance, filter capacitance, and the selected gain because sensor loading can dominate the practical accuracy.
추천
Low-Voltage Audio and Control Buffers
The MCP6034-E/SL can serve as a low-frequency audio or control-signal buffer in systems operating from a single low-voltage rail. Rail-to-rail input and output operation improves signal range near the supply limits, while the quad configuration allows four buffered channels in one package. Its 10 kHz gain-bandwidth product is appropriate for control paths and low-bandwidth audio functions, not high-frequency full-range audio reproduction. Designers should evaluate output-current capability, capacitive-load stability, distortion, and noise before assigning it to a precision audio path.
추천
Data Acquisition Interface
The MCP6034-E/SL is useful ahead of a low-speed multiplexer or ADC in compact data-acquisition equipment. Four channels can provide independent gain, filtering, or buffering stages, while the 900 nA typical current per amplifier supports low-power acquisition. The 10 kHz gain-bandwidth product must be matched to the intended signal bandwidth; it is suitable for temperature, pressure, and position measurements but not rapid waveform acquisition. Validate settling time, source impedance, ADC input range, and common-mode voltage during the analog-interface design.
추천
추천 제품 요약
엔지니어링 참조 데이터: MCP6034-E/SL — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MCP6034-E/ST | MCP6034-I/SL | MCP6034-I/ST |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC |
| Number of Amplifiers | 4 channels | 4 channels | 4 channels | 4 channels |
| Gain-Bandwidth Product | 10 kHz | 10 kHz | 10 kHz | 10 kHz |
| Typical Operating Current | 900 nA per amplifier | 900 nA per amplifier | 900 nA per amplifier | 900 nA per amplifier |
| Input Offset Voltage | Less than 150 uV | Less than 150 uV | Less than 150 uV | Less than 150 uV |
| Minimum Single-Supply Voltage | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Input and Output Operation | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output |
| Temperature Grade | Extended-temperature grade indicated by E suffix | Extended-temperature grade indicated by E suffix | Industrial-temperature grade indicated by I suffix | Industrial-temperature grade indicated by I suffix |
| Process Technology | Advanced CMOS | Advanced CMOS | Advanced CMOS | Advanced CMOS |
주요 차별점
- Combines four low-power precision amplifier channels in one package (vs MCP602-E/SN)
- Supports very low single-supply operation (vs MCP6034-I/SL)
- Maintains the same core electrical performance across listed MCP6034 options (vs MCP6034-E/ST)
설계 노트
Do not treat the 10 kHz gain-bandwidth product as a signal-accuracy limit independent of gain. For example, closed-loop bandwidth and settling behavior change with the selected noise gain. Calculate the required small-signal bandwidth, allowable source impedance, and settling time for the actual feedback network. The MCP6034-E/SL is best suited to low-frequency sensor and control signals rather than fast transient capture.
Place each amplifier's input, feedback components, and decoupling capacitor close to the associated pins. Keep sensitive input traces away from switching nodes and high-current return paths. For high-impedance sensors, use short traces, guard structures where appropriate, and clean PCB surfaces to limit leakage and contamination-induced bias errors. The low 900 nA typical current per amplifier does not eliminate input-node leakage constraints.
Use rail-to-rail input and output capability to maximize low-voltage signal range, but verify the output swing under the expected load current. Allow sufficient headroom for output saturation during startup, sensor faults, and control transients. Bypass the supply pins with local ceramic capacitance and keep the return current path short so switching noise on the supply rail does not become analog signal error.
Check stability with the actual sensor, filter capacitors, cable capacitance, and output load rather than assuming the nominal 10 kHz gain-bandwidth product guarantees an unconditionally stable amplifier. Add isolation resistors near the amplifier output when driving capacitive loads, then confirm settling and overshoot on the assembled board. This is especially important in long-cable sensor installations and multiplexed acquisition boards.
규정 준수 정보
Compliance and automotive qualification information must be confirmed for the exact ordering code using Microchip product documentation.