MCP6043-E/SN - 1.6V RRO Op Amp | Microchip Technology
부품 번호: MCP6043-E/SN ✓ 활성MCP6043-E/SN 개요
An operational amplifier is a high-gain, differential-input analog building block used to amplify weak sensor signals, buffer inputs, perform active filtering, and drive control stages. The MCP6043 belongs to the operational-amplifier hierarchy within analog and power-management semiconductors. Its rail-to-rail input and output behavior allows useful signal operation near the positive and negative supply limits, while its low-voltage capability supports compact battery-powered equipment.
The device operates from a single supply as low as 1.6 V. According to the manufacturer datasheet, its gain-bandwidth product is approximately 14 kHz, making it appropriate for low-frequency rather than high-speed signal paths. The amplifier also draws less than 1 µA maximum quiescent current per amplifier, as stated for the MCP6041/MCP6042/MCP6043/MCP6044 family, helping reduce standby consumption in portable and wearable products.
The MCP6043-E/SN combines rail-to-rail input and output stages with a general-purpose single-amplifier configuration. Its approximately 14 kHz bandwidth is adequate for resistive sensor bridges, temperature sensing, slow current monitoring, and low-frequency filter networks. Because the device is unity-gain stable, it can also be used in conventional non-inverting and inverting amplifier topologies without an external compensation network.
Typical applications include industrial process-control interfaces, low-power battery-operated instruments, portable measurement equipment, wearable accessories, buffered sensor inputs, and low-frequency active filters. The SOIC-8 package is also convenient for prototypes and mixed-signal boards where through-hole-style assembly, inspection, and hand rework are useful.
When designing around the MCP6043-E/SN, check input common-mode range, output swing, capacitive-load stability, noise, and gain-bandwidth interaction under the actual supply voltage. Place bypass capacitors close to the supply pins, keep feedback routes short, and use resistive isolation when driving capacitive loads. The low bandwidth is beneficial for noise control but unsuitable for high-speed acquisition or waveform reproduction.
This product record combines the manufacturer specifications with package details, application guidance, verified drop-in comparisons, PCB implementation notes, and a parameter-by-parameter selection framework. It helps engineers determine whether the MCP6043-E/SN provides sufficient speed, power efficiency, voltage range, and package compatibility before beginning a board-level design.
드롭인 대체품: MCP6043-E/SN — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: MCP6043-E/SN (동일 폼 팩터 및 풋프린트) — 차이점: Gain-Bandwidth Product, Quiescent Current.
MCP6043-I/SN
✅ 드롭인가격 문의
데이터시트 보기 →MCP6043-E/CH
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MCP6043-E/SN 최대 정격 & 전기적 특성
| Product Type | Single operational amplifier |
| Manufacturer | Microchip Technology |
| Minimum Supply Voltage | 1.6 V |
| Gain-Bandwidth Product | Approximately 14 kHz |
| 대기 전류 | Less than 1 µA maximum per amplifier |
| Input Topology | Rail-to-rail |
| Output Topology | Rail-to-rail |
| Number of Amplifiers | 1 |
| Unity-Gain Stability | Stable |
| 패키지 | 8-lead SOIC |
| Package Width | 3.90 mm |
| 실장 유형 | Surface mount |
| Typical Signal Frequency | Low frequency |
| GBW | Approximately 14 kHz |
MCP6043-E/SN 핀 구성
| 핀 1 | NC — Not connected |
| 핀 2 | VIN- — Inverting input |
| 핀 3 | VIN+ — Non-inverting input |
| 핀 4 | V- — Negative supply or ground for a single-supply configuration |
| 핀 5 | NC — Not connected |
| 핀 6 | VOUT — Analog output |
| 핀 7 | V+ — Positive supply input |
| 핀 8 | NC — Not connected |
일반적인 애플리케이션
MCP6043-E/SN 적합 용도: 6 애플리케이션s: Battery-Powered Sensor Conditioning, Industrial Process-Control Interface, Portable Measurement Equipment, Wearable Health and Comfort Sensor, Low-Frequency Active Filter, Audio and Communication Interface Buffering.
Battery-Powered Sensor Conditioning
The MCP6043-E/SN fits low-power sensor interfaces because it operates from a single 1.6 V supply and the MCP6041/MCP6042/MCP6043/MCP6044 family specifies less than 1 µA maximum quiescent current per amplifier. Place the amplifier between a resistive sensor bridge and an ADC input, using the rail-to-rail input stage for signals near either supply rail. Its approximately 14 kHz gain-bandwidth product is sufficient for temperature, pressure, and position sensors that change slowly. The principal trade-off is bandwidth: applications requiring rapid transients or video-rate signals need a faster amplifier. Check the entire signal chain for sensor current, leakage, ADC acquisition time, and the amplifier’s output-swing limits under the actual battery voltage.
추천
Industrial Process-Control Interface
The MCP6043-E/SN is appropriate for low-frequency industrial process-control inputs where the sensor produces a small differential voltage and the controller requires amplification close to the measurement source. Its rail-to-rail input and output characteristics provide useful signal range in compact single-supply systems, while unity-gain stability permits direct use in non-inverting and inverting configurations. The approximately 14 kHz gain-bandwidth product supports slow pressure, level, and flow measurements rather than fast closed-loop dynamics. Place the device close to the field input to limit interference pickup, and verify the guaranteed operating-temperature grade for the installation environment. Input protection, grounding, output isolation, and filtering must be added where field wiring exposes the amplifier to transients or common-mode voltage.
추천
Portable Measurement Equipment
The MCP6043-E/SN supports portable instruments that combine a low-voltage sensor, analog conditioning, and an ADC or display. Its 1.6 V minimum supply allows operation from compact energy-storage cells, and the family’s sub-1 µA maximum quiescent-current specification helps preserve standby life. The amplifier can buffer a high-impedance source, amplify a bridge signal, or implement an active low-pass filter before digitization. Its approximately 14 kHz bandwidth is well matched to slow physiological, environmental, and laboratory measurements, but it is not intended for waveform capture above the audio or low-frequency boundary. Select external resistor and capacitor values for the required noise, gain, and bandwidth, and confirm that the display or ADC input does not exceed the available output-voltage swing.
추천
Wearable Health and Comfort Sensor
The MCP6043-E/SN can condition low-frequency signals from wearable devices that monitor movement, temperature, respiration trends, or skin-contact sensors. Its rail-to-rail operation is valuable when the usable signal range is close to the low single-supply rail, and its low quiescent current is advantageous in designs that spend most of their time in standby. The approximately 14 kHz bandwidth avoids unnecessary signal bandwidth for slow physiological trends. Place the amplifier near the sensor connector, keep high-impedance input routes short, and use guarding or shielding if moisture or nearby switching circuitry raises noise. Validate skin-contact safety, electrode biasing, ESD protection, and the complete battery current budget before production use.
추천
Low-Frequency Active Filter
The MCP6043-E/SN is suitable for first-order and low-Q active filters because it is unity-gain stable and provides approximately 14 kHz gain-bandwidth product for low-frequency networks. It can implement buffering, Sallen-Key sections, and inverting filters for audio, control, or measurement paths. Select resistor and capacitor values so the closed-loop gain at each filter corner remains compatible with the amplifier’s gain-bandwidth response. Place the feedback components close to the amplifier, maintain symmetrical resistance values where practical, and keep high-impedance nodes short to reduce leakage and noise pickup. Because the device is intended for low-frequency operation, do not use it as a wideband filter or line driver without additional bandwidth verification.
추천
Audio and Communication Interface Buffering
The MCP6043-E/SN can buffer low-level audio or communication-interface signals when the required bandwidth remains low. Unity-gain stability makes it convenient for impedance conversion, and the rail-to-rail output can support small-signal stages operating near the supply limits. The approximately 14 kHz bandwidth covers many control-band and low-frequency audio functions but does not provide the slew rate or wideband performance expected from a line-level audio amplifier. For microphone or line inputs, verify input-noise contribution, output swing into the next stage, and stability with the cable or codec capacitance. A small isolation resistor at the output is appropriate when the load is capacitive, followed by an oscilloscope check for peaking or ringing.
추천
추천 제품 요약
엔지니어링 참조 데이터: MCP6043-E/SN — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MCP6043-I/SN | MCP6043-E/CH |
|---|---|---|---|
| Package | 8-lead SOIC | 8-lead SOIC | 8-lead SOIC |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Amplifier Count | 1 | 1 | 1 |
| Minimum Supply Voltage | 1.6 V | 1.6 V | 1.6 V |
| Gain-Bandwidth Product | Approximately 14 kHz | Approximately 14 kHz | Approximately 14 kHz |
| Maximum Quiescent Current | Less than 1 µA per amplifier | Less than 1 µA per amplifier | Less than 1 µA per amplifier |
| Input Common-Mode Behavior | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Output Swing Behavior | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Unity-Gain Stability | Stable | Stable | Stable |
| Primary Ordering Difference | E temperature-grade code with SN suffix | I temperature-grade code with SN suffix | E temperature-grade code with CH suffix |
주요 차별점
- Very low quiescent current for portable analog conditioning (vs MCP6043-I/SN)
- Single 1.6 V-compatible amplifier in an 8-lead SOIC (vs MCP6043-E/CH)
- Low-frequency performance matched to slow sensing and control loops (vs MCP6043-I/SN)
설계 노트
Connect the positive supply to pin 7 and the negative supply or ground to pin 4. Place a local bypass capacitor close to each supply pin and provide its return directly to the ground plane. Because the family specification permits less than 1 µA maximum quiescent current, capacitor leakage can materially affect a standby power budget; use a low-leakage dielectric when operating near the device’s current limit. Do not rely on the amplifier quiescent current as the entire system standby figure because sensor biasing, protection leakage, and load current also contribute.
Keep the inverting-input and feedback components close to pins 2 and 6, and minimize the distance from the non-inverting input at pin 3 to the source. Avoid routing sensitive input signals beside the supply pins, clock lines, or switching-node traces. For high-impedance sensors, use a grounded guard where practical and keep the board surface under the input path free of solder flux and contamination. These layout practices reduce leakage, induced hum, and pickup that could otherwise dominate a low-frequency measurement.
Do not interpret rail-to-rail as an unlimited output range; the output must remain inside the supply rails under the specified load. Similarly, the 1.6 V supply limit does not guarantee identical performance at every lower operating voltage. Review the electrical-characteristics curves for common-mode range, output swing, gain error, and supply-current behavior at the actual rail voltage. Avoid using the MCP6043-E/SN for high-speed signals because its approximately 14 kHz gain-bandwidth product is intended for low-frequency applications.
규정 준수 정보
Compliance declarations for this exact orderable part were not identified. Confirm the current material and environmental declarations with the manufacturer before production release.