MCP604T-E/ST - 2.8 MHz Quad RRO Op Amp | Microchip
부품 번호: MCP604T-E/ST ✓ 활성MCP604T-E/ST 개요
An operational amplifier is an amplifier IC that uses high open-loop gain to amplify the difference between two input voltages. The MCP604 belongs to the CMOS operational-amplifier hierarchy, which combines rail-to-rail output capability, low bias current, low supply current, and moderate bandwidth. These characteristics place it between precision micropower amplifiers and higher-speed signal-chain amplifiers designed for substantially wider bandwidth.
The four amplifiers are optimized for low-power operation while retaining useful signal-chain performance. The 2.8 MHz gain-bandwidth product supports closed-loop operation at frequencies determined by the selected noise gain, while 230 uA typical operating current supports four amplifiers in compact, low-power systems. Rail-to-rail output swing increases usable output range near the supply rails, and the low-bias-current architecture is advantageous when driving high-impedance sensors.
The MCP604 family uses Microchip CMOS technology to provide low input bias current, high open-loop gain, high-speed operation, and rail-to-rail output swing. Its 2.7 V minimum supply permits operation from a single 3.3 V rail. The quad configuration reduces package count compared with four individual single amplifiers, while separate amplifier sections can independently provide voltage gain, buffering, filtering, or differential signal conditioning.
Typical uses include portable sensor interfaces, low-voltage instrumentation, industrial measurement circuits, active filters, and general-purpose analog signal conditioning. The MCP604 is also appropriate for four-channel acquisition systems where each amplifier drives a high-impedance sensor or buffers an ADC input. For designs requiring a faster amplifier, greater output current, or lower operating current, a different device with clearly different electrical ratings should be selected rather than treated as an automatic replacement.
Decouple each supply pin with a local high-frequency ceramic capacitor and provide stable reference or return paths according to the manufacturer's application guidance. Decoupling capacitors should be placed close to the device, and sensitive feedback networks should be routed away from switching nodes. Verify output swing, load capability, stability, and input common-mode behavior against the application before releasing a production design.
This page combines manufacturer specifications, package and lifecycle information, drop-in replacement analysis, comparison parameters, and practical circuit guidance. It is intended to help engineers distinguish the MCP604T-E/ST from temperature-grade, channel-count, bandwidth, and package variants before committing a design to a specific land pattern.
드롭인 대체품: MCP604T-E/ST — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: MCP604T-E/ST (동일 폼 팩터 및 풋프린트) — 차이점: Gain-Bandwidth Product, Package, Typical Operating Current, Amplifier Type, Process Technology.
MCP604T-I/ST
✅ 드롭인가격 문의
데이터시트 보기 →MCP604-I/ST
✅ 드롭인가격 문의
데이터시트 보기 →MCP604-E/ST
✅ 드롭인가격 문의
데이터시트 보기 →MCP604T-E/ST 최대 정격 & 전기적 특성
| Amplifier Count | 4 amplifiers |
| Gain-Bandwidth Product | 2.8 MHz |
| Typical Operating Current | 230 uA |
| Minimum Single-Supply Voltage | 2.7 V |
| Maximum Single-Supply Voltage | 6.0 V |
| Output Swing | Rail-to-rail |
| 패키지 | 14-pin TSSOP |
| 실장 유형 | Surface mount |
| Process Technology | CMOS |
MCP604T-E/ST 핀 구성
| 핀 1 | NC — Not connected (per datasheet) |
| 핀 2 | -INA — Inverting input for amplifier A |
| 핀 3 | +INA — Non-inverting input for amplifier A |
| 핀 4 | V- — Negative supply connection |
| 핀 5 | +INB — Non-inverting input for amplifier B |
| 핀 6 | -INB — Inverting input for amplifier B |
| 핀 7 | OUTB — Output for amplifier B |
| 핀 8 | OUTA — Output for amplifier A |
| 핀 9 | +INC — Non-inverting input for amplifier C |
| 핀 10 | -INC — Inverting input for amplifier C |
| 핀 11 | V+ — Positive supply connection |
| 핀 12 | -IND — Inverting input for amplifier D |
| 핀 13 | +IND — Non-inverting input for amplifier D |
| 핀 14 | OUTD — Output for amplifier D |
일반적인 애플리케이션
MCP604T-E/ST 적합 용도: 6 애플리케이션s: Portable Sensor Signal Conditioning, Industrial Instrumentation, Precision Active Filters, Low-Power ADC Signal Conditioning, Audio Preamplifier and Buffer, General-Power 5 V Control and Interface.
Portable Sensor Signal Conditioning
The MCP604T-E/ST suits portable sensing systems that require four buffered channels and operate from a 3.3 V battery-derived rail. Its 230 uA typical operating current provides a defined starting point for power-budget analysis, while the 2.8 MHz gain-bandwidth product supports low-frequency gain stages and active filters. Rail-to-rail output swing helps maximize signal range near the available supply voltage. Use one amplifier section for each sensor or conditioning channel, place bypass capacitance close to the supply pins, and verify that source impedance and capacitive loading will not compromise closed-loop stability.
추천
Industrial Instrumentation
The MCP604T-E/ST can provide input buffering, gain, active filtering, and output driving in compact industrial instrumentation. Its 2.8 MHz gain-bandwidth product is appropriate for signals spanning audio and low-frequency measurement bands, and the quad configuration reduces the number of amplifier packages required. Operation from a single 2.7 V to 6.0 V supply simplifies systems built around 3.3 V or 5 V rails. Keep high-impedance sensor paths short, maintain a quiet ground reference, and verify that the selected temperature grade covers the enclosure's measured operating range.
추천
Precision Active Filters
The four MCP604T-E/ST amplifier sections can implement multiple Sallen-Key or multiple-feedback active-filter stages in a low-voltage system. A 2.8 MHz gain-bandwidth product gives the closed-loop amplifier useful bandwidth above the frequency ranges commonly used for slow sensor and audio-band filtering. Component tolerances determine much of the filter accuracy, so use suitable resistor and capacitor tolerances and keep the feedback network compact. Validate stability with the actual source and load impedances, especially when the filter drives an ADC or long PCB trace.
추천
Low-Power ADC Signal Conditioning
The MCP604T-E/ST is suitable for conditioning up to four low-level analog signals before conversion by an ADC. Its low-bias-current CMOS input architecture supports high-impedance sources, while 2.8 MHz gain-bandwidth product provides more than enough bandwidth for many low-frequency conversion systems. Rail-to-rail output can improve use of the available supply range, although input common-mode and output-swing limits must be checked for the selected gain. Use short traces, dedicated return paths, and anti-alias filtering before the converter input.
추천
Audio Preamplifier and Buffer
The MCP604T-E/ST can provide four channels of voltage gain, impedance buffering, and simple active filtering in low-voltage audio equipment. Its rail-to-rail output swing is useful when the signal must use most of a 3.3 V or 5 V rail, and the 2.8 MHz gain-bandwidth product covers a wide range of conventional audio-band applications. The amplifier is not a high-current headphone driver, so use a separate output stage when driving low-ohm loads. Confirm distortion, output swing, and stability against the intended feedback gain and load impedance.
추천
General-Power 5 V Control and Interface
The MCP604T-E/ST fits 5 V control boards that need several general-purpose amplifier channels for level shifting, filtering, comparators, or impedance isolation. Its single-supply range of 2.7 V to 6.0 V and 230 uA typical operating current support compact control electronics, while four sections provide flexible channel allocation. Check input and output behavior near the rails before choosing high gain, because the rail-to-rail output specification does not imply unrestricted input common-mode operation. Decouple the device locally and keep feedback paths away from digital switching returns.
추천
추천 제품 요약
엔지니어링 참조 데이터: MCP604T-E/ST — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MCP604T-I/ST | MCP604-I/ST | MCP604-E/ST |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 14-TSSOP | 14-TSSOP - same | 14-TSSOP - same | 14-TSSOP - same |
| Amplifier Count | 4 amplifiers | 4 amplifiers | 4 amplifiers | 4 amplifiers |
| Gain-Bandwidth Product | 2.8 MHz | 2.8 MHz | 2.8 MHz | 2.8 MHz |
| Typical Operating Current | 230 uA | 230 uA | 230 uA | 230 uA |
| Minimum Supply Voltage | 2.7 V | 2.7 V | 2.7 V | 2.7 V |
| Maximum Supply Voltage | 6.0 V | 6.0 V | 6.0 V | 6.0 V |
| Output Swing | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Special Features | Low bias current, rail-to-rail output | Low bias current, rail-to-rail output | Low bias current, rail-to-rail output | Low bias current, rail-to-rail output |
주요 차별점
- Quad amplifier integration (vs MCP6024T-E/ST)
- Exact MCP604-family footprint and topology (vs MCP604T-I/ST)
- Low-voltage rail-to-rail output capability (vs MCP604-E/ST)
설계 노트
Place the supply bypass capacitor directly between the V+ and V- pins and the ground plane rather than routing the supply through a long loop. A short, low-impedance return path reduces the effective series inductance and helps the amplifier respond cleanly to fast input and output transitions. Keep the TSSOP footprint, exposed pad status, solder-mask definition, and paste pattern consistent with the manufacturer land-pattern guidance.
Route high-impedance inputs, noninverting inputs, and feedback components as short and compact as practical. Parasitic capacitance across a high-value feedback resistor can reduce phase margin, particularly when the amplifier operates near the 2.8 MHz gain-bandwidth-product region. For sensor interfaces, maintain a quiet ground reference and avoid placing analog input traces beside clocks, pulse-width-modulator outputs, or switching-regulator power paths.
Begin the power-budget calculation with the documented 230 uA typical operating-current figure and add the load current from every amplifier channel. Because the MCP604T-E/ST supports a single supply, check whether the negative supply pin is connected to ground in the intended topology. Confirm actual quiescent current and output-current behavior in the final circuit rather than assuming the typical value applies across all operating conditions.
규정 준수 정보
Compliance status was not stated in the cited manufacturer or distributor records. The device is an operational amplifier rather than an automotive-qualified product, so AEC-Q100 is not applicable unless Microchip identifies a specific automotive order code.