MCP6284-E/P - Quad 5MHz Rail-to-Rail Op Amp | Microchip
부품 번호: MCP6284-E/P ✓ 활성MCP6284-E/P 개요
An operational amplifier, or op amp, is an analog semiconductor that amplifies the difference between two input voltages. The MCP6284 belongs to the general-purpose op amp category within the broader analog IC and signal-conditioning hierarchy. Its four independent amplifiers can be used for voltage buffering, gain stages, active filtering, instrumentation, sensor interfaces, and low-frequency signal processing.
Key features include a 5 MHz gain-bandwidth product and 65° phase margin, which support stable operation in a wide range of feedback networks. The rail-to-rail input and output swing allows the amplifier to operate close to the supply rails, improving useful signal range in low-voltage systems. Typical quiescent current is 450 µA per amplifier, helping reduce power consumption in portable and low-power designs.
The MCP6284-E/P uses a general-purpose, low-power amplifier architecture intended for single-supply operation. Because it is specified from 2.2 V to 5.5 V, the device can operate directly from 3.3 V and 5 V rails. The 2.5 V/µs slew rate is useful for signals that require faster transitions than a low-bandwidth precision amplifier can provide, while the rail-to-rail output improves dynamic range when the operating voltage is constrained.
Typical applications include sensor signal conditioning, audio and communication signal paths, active filters, data-acquisition front ends, buffer stages, and general-purpose analog control circuits. The 14-pin DIP package also makes the MCP6284-E/P convenient for prototyping, educational platforms, through-hole assembly, and applications where a socketed or easily inspectable package is preferred.
When designing a circuit around the MCP6284-E/P, verify the input common-mode range, output swing, capacitive-load stability, and noise performance against the actual signal conditions. Place bypass capacitors close to the supply pins and use short feedback paths to reduce parasitic effects. The quad configuration allows independent amplifiers to share a supply arrangement, but each amplifier should be evaluated independently for stability, offset, noise, and output-current requirements.
This product page combines the manufacturer family specifications, package information, sourcing links, pin assignment, application guidance, and practical design notes to support faster engineering decisions. For the most detailed electrical limits, test conditions, and ordering information, use the official Microchip MCP6284 product page and the linked manufacturer datasheet.
드롭인 대체품: MCP6284-E/P — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
MCP6284-E/PCH
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
MCP6284-E/P 최대 정격 & 전기적 특성
| Product Type | Quad general-purpose operational amplifier |
| Number of Amplifiers | 4 circuits |
| Gain-Bandwidth Product | 5 MHz |
| Slew Rate | 2.5 V/µs |
| Phase Margin | 65° |
| Supply Voltage Range | 2.2 V to 5.5 V |
| 대기 전류 | 450 µA typical per amplifier |
| Input Swing | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Amplifier Type | General-purpose |
| 패키지 | 14-pin DIP, 0.300 inch (7.62 mm) |
| 실장 유형 | Through-hole |
| Packaging | Tube |
| RoHS 상태 | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
MCP6284-E/P 핀 구성
| 핀 1 | OUTA — Output of amplifier A |
| 핀 2 | -INA — Inverting input of amplifier A |
| 핀 3 | +INA — Non-inverting input of amplifier A |
| 핀 4 | V- — Negative supply connection |
| 핀 5 | +INB — Non-inverting input of amplifier B |
| 핀 6 | -INB — Inverting input of amplifier B |
| 핀 7 | OUTB — Output of amplifier B |
| 핀 8 | OUTC — Output of amplifier C |
| 핀 9 | -INC — Inverting input of amplifier C |
| 핀 10 | +INC — Non-inverting input of amplifier C |
| 핀 11 | V+ — Positive supply connection |
| 핀 12 | +IND — Non-inverting input of amplifier D |
| 핀 13 | -IND — Inverting input of amplifier D |
| 핀 14 | OUTD — Output of amplifier D |
일반적인 애플리케이션
MCP6284-E/P 적합 용도: 6 애플리케이션s: Sensor Signal Conditioning, Active Filter Design, Audio and Communication Buffers, Data Acquisition Front End, Industrial Control and Instrumentation, Prototype and Educational Electronics.
Sensor Signal Conditioning
The MCP6284-E/P is well suited to conditioning outputs from low-voltage sensors because its rail-to-rail input and output swing preserves usable signal range in 2.2 V to 5.5 V systems. Use one amplifier as a voltage follower and the remaining channels for gain or filtering stages. Its 5 MHz gain-bandwidth product supports moderate-bandwidth signals, while 2.5 V/µs slew rate handles required output transitions. Check sensor source impedance and bias current before choosing the gain topology, and confirm that the input common-mode range covers the complete sensor waveform.
추천
Active Filter Design
The MCP6284-E/P can implement first- and second-order active filters in audio, measurement, and control circuits. Its 5 MHz gain-bandwidth product gives designers bandwidth above typical low-frequency filter cutoffs, and the 65° phase margin supports commonly used feedback configurations. The 14-pin DIP package simplifies through-hole prototype construction and allows individual amplifier sections to be evaluated. Component tolerances, gain-bandwidth variation, capacitive loading, and output-swing headroom should be checked while calculating the filter response.
추천
Audio and Communication Buffers
The MCP6284-E/P provides four buffered channels for low-level audio, communications, and instrumentation interfaces. Rail-to-rail input and output capability is valuable when signals approach either supply rail, and the 450 µA typical quiescent current per amplifier supports low-power operation. The 2.5 V/µs slew rate can improve large-signal response compared with very slow micropower amplifiers. Designers should still evaluate distortion, noise, output load, stability into capacitive loads, and the bandwidth of the surrounding signal path.
추천
Data Acquisition Front End
The MCP6284-E/P can form the input conditioning section of a low-speed or moderate-speed data-acquisition system. Four independent channels allow instrumentation, differential conversion, anti-alias filtering, or reference buffering to be implemented without using four separate packages. The 5 MHz gain-bandwidth product accommodates many precision-measurement front ends, while rail-to-rail operation helps with restricted sensor ranges. Validate input capacitance, settling behavior, offset, noise, and common-mode performance for the selected gain and sampling rate.
추천
Industrial Control and Instrumentation
The MCP6284-E/P is appropriate for general-purpose industrial control and instrumentation circuits operating from 3.3 V or 5 V rails. It can amplify control signals, buffer sensor outputs, and drive analog stages within the limits of the selected gain and load. The through-hole DIP package is useful for industrial controller assemblies that use socketed or manually serviced analog boards. Because the family is a general-purpose amplifier rather than an automotive-qualified device, verify environmental, lifecycle, and compliance requirements for the target installation.
추천
Prototype and Educational Electronics
The MCP6284-E/P is particularly convenient for prototypes, laboratory instruments, and educational electronics because four amplifiers are available in an inspectable 14-pin DIP package. The package is easy to insert into a breadboard or socket and allows straightforward access to power, input, and output pins. Its 5 MHz bandwidth is more than adequate for many basic amplifier, comparator-style, oscillator, and filter experiments. Begin with a unity-gain configuration, verify supply decoupling, and avoid exceeding the input and output limits documented by Microchip.
추천
엔지니어링 참조 데이터: MCP6284-E/P — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
설계 노트
Place a supply bypass capacitor close to pins 11 and 4, and connect the ground return directly to the amplifier supply reference. The MCP6284-E/P supports a single supply from 2.2 V to 5.5 V, but the usable signal range still depends on the common-mode and output-swing limits for the selected conditions. Use separate, short supply paths for each amplifier section when driving multiple loads.
Keep input and feedback traces short and route them away from noisy switching nodes and high-current return paths. The 14-pin DIP footprint simplifies through-hole assembly, but lead inductance can become important in fast feedback loops. Place input and output decoupling components close to their associated pins, and avoid long parallel runs between the amplifier and sensitive source components.
Do not assume that rail-to-rail input and output means zero headroom. Check the manufacturer limits for input common-mode range, output swing, output current, and capacitive loading at the intended supply voltage and temperature. Also verify that a chosen replacement has the same 14-pin DIP footprint and equivalent amplifier pin functions; changing to an SOIC package requires a PCB change.
규정 준수 정보
The available product and distributor information does not state the compliance declarations for this exact orderable part. Confirm current RoHS, REACH, lead-free, halogen-free, and conflict-minerals documentation with Microchip.