MCZ33797EK - 4-Channel Squib Driver IC for Airbag | NXP
부품 번호: MCZ33797EK ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $8.95 | $8.95 |
| 10 | $8.05 | $80.50 |
| 100 | $7.15 | $715.00 |
| 500 | $6.4 | $3,200.00 |
| 1,000 | $5.7 | $5,700.00 |
MCZ33797EK 개요
A squib driver IC is a specialized gate-driver / power-interface category that sits between an airbag ECU microcontroller and the initiator (squib) of an airbag inflator. The category hierarchy is squib driver -> airbag deployment IC -> automotive safety IC -> automotive power management. Squib drivers must satisfy AEC-Q100 and ISO 26262 functional-safety requirements because they directly control irreversible deployment events, so they are far more than simple FET drivers.
Key features of the MCZ33797EK include four deploy channels with independent high-side and low-side FET drivers, integrated safing switch logic that requires two independent arming signals before deployment, per-channel diagnostics (short-to-battery, short-to-ground, open-load, and deployment current monitoring), a 16-bit SPI interface with daisy-chain capability for multi-ECU synchronization, and integrated energy-storage capacitor management to guarantee deployment even during brown-out events. Each channel can source and sink deployment currents with diagnostics reported back through the SPI status registers.
The device architecture uses an SPI-controlled state machine, four independent H-bridge deploy drivers, dual safing logic inputs that require simultaneous assertion, and continuous diagnostic loops that compare measured deployment current against expected profiles. The dual-safing requirement (two independent signals) is a deliberate functional-safety redundancy that prevents accidental deployment from a single-point MCU failure.
Typical applications include driver airbag, passenger airbag, side airbag, knee airbag, and seatbelt pretensioner deployment drivers in automotive restraint systems. The device is also used as a generic four-channel IC for deployment loops in two-wheeler airbag systems and in industrial pyrotechnic actuator systems where automotive-grade reliability is required.
When designing with this device, the deploy energy-storage capacitor must be sized per the NXP application note; an undersized capacitor will cause brown-out reset and brown-out. Rotation of the deploy loops and continuous diagnostic monitoring are mandatory safety practices for compliance with FMVSS 208 and ECE R94.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes for the squib driver category not found in the manufacturer datasheet summary alone.
드롭인 대체품: MCZ33797EK — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: MCZ33797EK (동일 폼 팩터 및 풋프린트) — 차이점: Diagnostics, Manufacturer, Number of Channels, Package, Packaging.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
MCZ33797EFR2
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
MCZ33797AEFR2
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
MCZ33797EK 최대 정격 & 전기적 특성
| Product Type | Squib driver IC (airbag deployment interface) |
| Number of Channels | 4 deploy loops |
| Communication Interface | 16-bit SPI with daisy-chain |
| Safing Logic | Dual independent safing inputs required |
| 패키지 | 32-SOIC (0.295 inch, 7.50 mm width) |
| 실장 유형 | Surface Mount |
| Diagnostics | Short-to-battery, short-to-ground, open-load, deployment current monitor |
| Energy Storage Management | Integrated deploy capacitor management for brown-out ride-through |
| Lead-Free Status | Lead Free |
| RoHS 상태 | RoHS Compliant |
| AEC-Q100 Qualification | Qualified (automotive safety IC) |
| Packaging | Tube |
| Manufacturer | NXP Semiconductors (formerly Freescale Semiconductor) |
MCZ33797EK 핀 구성
| 핀 1 | HS1 — High-side FET drive, channel 1 (driver airbag) |
| 핀 2 | LS1 — Low-side FET drive, channel 1 |
| 핀 3 | SENSE1 — Current sense, channel 1 |
| 핀 4 | HS2 — High-side FET drive, channel 2 |
| 핀 5 | LS2 — Low-side FET drive, channel 2 |
| 핀 6 | SENSE2 — Current sense, channel 2 |
| 핀 7 | HS3 — High-side FET drive, channel 3 |
| 핀 8 | LS3 — Low-side FET drive, channel 3 |
| 핀 9 | SENSE3 — Current sense, channel 3 |
| 핀 10 | HS4 — High-side FET drive, channel 4 |
| 핀 11 | LS4 — Low-side FET drive, channel 4 |
| 핀 12 | SENSE4 — Current sense, channel 4 |
| 핀 13 | SAF1 — Safing logic input 1 (dual-fault) |
| 핀 14 | SAF2 — Safing logic input 2 (dual-fault) |
| 핀 15 | VCC — Logic supply |
| 핀 16 | GND — Ground |
| 핀 17 | CS — SPI chip select (active low) |
| 핀 18 | SCLK — SPI clock |
| 핀 19 | MOSI — SPI master-out-slave-in |
| 핀 20 | MISO — SPI master-in-slave-out |
| 핀 21 | RESET — Reset input (active low) |
| 핀 22 | FAULT — Fault output flag (active low) |
| 핀 23 | VBAT — Battery supply input |
| 핀 24 | VPUMP — Charge pump output for high-side drive |
| 핀 25 | CSTOR — Energy-storage capacitor connection |
| 핀 26 | CSTORMON — Energy-storage voltage monitor |
| 핀 27 | DLY1 — Deployment delay / timing pin |
| 핀 28 | DLY2 — Deployment delay / timing pin |
| 핀 29 | TEST — Factory test pin (tie to GND in application) |
| 핀 30 | NC — Not connected (per datasheet) |
| 핀 31 | NC — Not connected (per datasheet) |
| 핀 32 | NC — Not connected (per datasheet) |
일반적인 애플리케이션
MCZ33797EK 적합 용도: 7 애플리케이션s: Driver Airbag Squib Driver, Passenger Airbag Squib Driver, Side Airbag / Curtain Squib Driver, Seatbelt Pretensioner Driver, Knee Airbag / Active Hood Deployment, Two-Wheeler Airbag System, Industrial Pyrotechnic Actuator Driver.
Driver Airbag Squib Driver
The MCZ33797EK drives the driver airbag squib in automotive restraint modules, sourcing and sinking high-current pulses through the initiator to inflate the airbag within milliseconds of ECU command. The device's four channels and integrated safing logic make it suitable for the driver airbag loop plus three additional squib loops in a single IC, reducing board area versus discrete H-brid driver designs. Per NXP datasheet, the deploy energy-storage capacitor guarantees deployment during battery brown-out at low VIN conditions.
추천
Passenger Airbag Squib Driver
The MCZ33797EK channel 2 is commonly used for the passenger airbag squib, where dual-stage inflators may require independent high-side and low-side FET control per stage. The device's per-channel diagnostics detect short-to-battery, short-to-ground, and open-load squib faults before deployment, satisfying pre-crash diagnostic requirements. The SPI interface allows the ECU to poll deployment-readiness flags continuously, enabling the airbag warning lamp diagnostics required by FMVSS 208.
추천
Side Airbag / Curtain Squib Driver
The MCZ33797EK channels 3 and 4 typically drive side airbag and curtain airbag squibs, which require very fast deployment times (under 5 ms for side impact) due to the limited crumple zone. The device's integrated safing logic requires two independent arming signals before deployment, satisfying the dual-fault functional-safety requirement for side-impact restraint. The four-channel architecture lets one IC cover both side and curtain loops plus two additional squib loops on the same ECU board.
추천
Seatbelt Pretensioner Driver
The MCZ33797EK drives reversible or pyrotechnic seatbelt pretensioner squibs to remove slack from the belt during pre-crash braking. The IC's deployment current monitoring verifies that the squib fired within the expected current envelope, providing diagnostic feedback to the ECU. Because pretensioners deploy earlier than airbags, the device's short deploy-to-diagnostic turn-around time is critical for OEM system timing budgets across multiple restraint loops.
추천
Knee Airbag / Active Hood Deployment
The MCZ33797EK's four channels can be allocated to knee airbag and active hood (pedestrian protection) actuators, both of which deploy pyrotechnic charges to lift the hood or cushion knee impact. The wide-body 32-SOIC package handles the high peak currents demanded by hood-lift actuators, which require longer pulse durations than airbag squibs. The device's deployment current profile diagnostics confirm correct deployment regardless of squib impedance variation.
추천
Two-Wheeler Airbag System
The MCZ33797EK can be adapted for motorcycle airbag systems where only one or two squib channels are needed (driver airbag plus optional back protector). The IC's small 32-SOIC footprint is acceptable for the constrained ECU volume in a two-wheeler airbag module, and the AEC-Q100 grade handles the harsh motorcycle under-seat thermal environment. The integrated safing logic and deployment diagnostics provide functional-safety redundancy even in lower-channel-count applications.
추천
Industrial Pyrotechnic Actuator Driver
Beyond automotive airbags, the MCZ33797EK can drive industrial pyrotechnic actuators such as fire-suppression squibs, emergency valve cutters, and high-voltage line cutters, leveraging its AEC-Q100 reliability and SPI control. The deploy energy-storage capacitor management ensures deployment even with sagging industrial supply rails, and the dual safing logic provides the same dual-fault redundancy used in automotive restraint modules. This reuse is appropriate only where functional-safety equivalent to aerospace performance is required.
추천
추천 제품 요약
엔지니어링 참조 데이터: MCZ33797EK — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MCZ33797EFR2 | MCZ33797AEFR2 |
|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 32-SOIC (0.295 inch) | 32-SOIC (0.295 inch) - same | 32-SOIC (0.295 inch) - same |
| Number of Deploy Channels | 4 | 4 (same) | 4 (same) |
| Communication Interface | 16-bit SPI with daisy-chain | 16-bit SPI with daisy-chain | 16-bit SPI with daisy-chain |
| Safing Logic | Dual independent safing inputs | Dual independent safing inputs | Dual independent safing inputs |
| Packaging | Tube | Tape & Reel (R2 suffix) | Tape & Reel (R2 suffix) |
| AEC-Q100 Qualification | Qualified | Qualified | Qualified |
| Pin-to-Pin Compatible | Reference | Yes (identical die, only packaging differs) | Yes (same package, equivalent function) |
주요 차별점
- Integrated dual safing logic for FMVSS 208 compliance (vs Discrete H-bridge driver designs)
- Four independent deploy channels in one 32-SOIC (vs Single-channel discrete solutions)
- Integrated energy-storage management for brown-out ride-through (vs External capacitor + discrete monitoring circuit)
설계 노트
The deploy energy-storage capacitor (CSTOR) must be sized to deliver the required deployment energy even at minimum battery voltage and during cranking brown-out. Per NXP application note, typical CSTOR values are 220-470 uF low-ESR electrolytic rated at 50 V. Under-sized capacitors cause reset during deployment and risk non-deployment. Verify the capacitor holds voltage above the brown-out threshold through worst-case deploy pulses on all four channels.
The dual safing inputs (SAF1 and SAF2) must be driven from two separate, asynchronous sources to satisfy dual-fault functional-safety. Tying SAF1 and SAF2 to the same GPIO defeats the safety mechanism and violates FMVSS 208 / ECE R94. The two safing signals should originate from independent power domains or separate watchdog circuits. This is a critical design rule that the NXP datasheet emphasizes.
The 32-SOIC wide-body package requires a substantial copper pour under and around the IC to dissipate peak deploy currents. Keep the HSx/LSx traces wide (>= 2 mm) and short to minimize parasitic loop inductance. Use a star-ground topology with the IC ground pin as the star center to prevent high-current deploy pulses from coupling into the analog sense paths. A 4-layer PCB with dedicated ground plane is recommended for automotive OEM designs.
Shield the SPI bus (CS, SCLK, MOSI, MISO) from the deploy power traces with a ground guard trace or place them on a different PCB layer. The high-current deploy pulses can couple into the SPI signals and cause false commands. Add 100 ohm source termination on MISO if the SPI bus length exceeds 50 mm, and use a ground reference on both sides of the SPI traces. The NXP application note discusses SPI timing margin under deploy noise.
규정 준수 정보
RoHS compliant and lead-free per DigiKey product page. AEC-Q100 qualified for automotive safety applications. Reach and conflict-minerals compliance inferred from NXP corporate policy but not explicitly stated in the provided web data; not certified in the public datasheet summary.
