MCZ33797EKR2 - 4-Channel Squib Driver IC | NXP Semiconductors
부품 번호: MCZ33797EKR2 ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $6.715 | $6.72 |
| 10 | $6.04 | $60.40 |
| 100 | $5.37 | $537.00 |
| 500 | $4.77 | $2,385.00 |
| 1,000 | $4.3 | $4,300.00 |
MCZ33797EKR2 개요
A squib driver is a specialized interface IC within the automotive safety and power management hierarchy (squib driver -> airbag deployment IC -> automotive safety IC -> integrated circuit) that sits between the airbag electronic control unit (ECU) and the pyrotechnic initiator in the inflator. Its primary role is to deliver a controlled, high-current deployment pulse on command from the ECU, while continuously monitoring squib health so the system can detect a missing, shorted, or aged initiator before it becomes a safety liability.
Key features include four independent deployment channels, programmable deployment current and timer profiles, integrated diagnostic functions (squib resistance measurement, short-to-ground, short-to-battery, and open-load detection), an SPI-compatible serial communications interface for ECU command/status exchange, and built-in fault counters. The device operates over the automotive battery range and is qualified to operate from -40 C to +85 C ambient. It includes watchdog and fault-output pins and supports both single-point and dual-point deployment configurations.
Technically, each channel combines a deploy high-side FET, deploy low-side FET, and a diagnostic analog front end. The diagnostic engine performs ratiometric resistance measurements against internal references, enabling detection of squib values outside the safe envelope. Deployment is initiated via SPI commands and executed with hardware handshaking to ensure deterministic timing.
Typical applications include driver-side airbag modules, passenger-side airbag modules, side-curtain airbag modules, knee airbag modules, and seat-belt pretensioner modules. Most commonly used by Tier-1 airbag ECU suppliers building dual-stage inflator systems where each squib is independently controllable and diagnosable.
Design consideration: the deployment energy is delivered by energy stored on bulk capacitors, so the board must include low-ESR bulk capacitance sized for the worst-case deployment profile. Pin 1 orientation and SOIC-32 pinout should be cross-checked against the manufacturer datasheet before PCB layout.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on a single manufacturer product page.
드롭인 대체품: MCZ33797EKR2 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: MCZ33797EKR2 (동일 폼 팩터 및 풋프린트) — 차이점: Diagnostics, Manufacturer, Number of Channels, Package, Packaging.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
MCZ33797EK
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$5.7 / 개
데이터시트 보기 →MCZ33797EKR2 사양
| 기능 | 4-Channel Squib Driver / Airbag Deployment Interface |
| Number of Channels | 4 |
| 패키지 | 32-SOIC (0.295", 7.50 mm width) |
| 실장 유형 | Surface Mount |
| Packaging | Tape & Reel (TR) |
| Lead Free Status | Lead Free |
| RoHS 상태 | RoHS Compliant |
| 인터페이스 | SPI-compatible serial interface |
| Diagnostics | Squib resistance, short-to-ground, short-to-battery, open-load |
| Deployment Channels per IC | 4 |
| Manufacturer | NXP Semiconductors (formerly Freescale) |
| Datasheet Document Size | 905 kB PDF |
| Datasheet Page Count | 34 pages |
MCZ33797EKR2 32-soic (0.295", 7.50 mm width) 핀 구성 가이드
MCZ33797EKR2(32-soic (0.295", 7.50 mm width) 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: MCZ33797EKR2.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
MCZ33797EKR2 적합 용도: 6 애플리케이션s: Driver-Side Airbag ECU, Passenger-Side Airbag Module, Side-Curtain Airbag Module, Knee Airbag ECU, Seat-Belt Pretensioner Module, Automotive Restraint Control Module.
Driver-Side Airbag ECU
The MCZ33797EKR2 fits driver-side airbag ECUs because each of its four squib channels can independently deploy a pyrotechnic inflator with a hardware-timed current pulse while continuous diagnostic monitoring verifies squib resistance stays within the qualified envelope before deployment. Its 32-SOIC footprint keeps the high-current loop compact on the ECU PCB, reducing parasitic inductance that would otherwise distort the deploy current profile. Compared with discrete H-bridge implementations, the integrated diagnostic engine removes the analog front end from the bill of materials and lets the ECU microcontroller issue deployment via SPI commands rather than low-level FET timing.
추천
Passenger-Side Airbag Module
For passenger-side airbag modules, the MCZ33797EKR2 provides four independent channels that comfortably cover the dual-stage inflator plus diagnostic requirements of a passenger airbag. The integrated short-to-ground, short-to-battery, and open-load detection features run on every ECU power-up, allowing OEMs to meet ISO 12097 airbag module diagnostic coverage without external comparators. The SPI status register reports fault counters so the ECU can flag a service-required condition before the vehicle leaves the assembly line.
추천
Side-Curtain Airbag Module
Side-curtain airbag modules benefit from the MCZ33797EKR2 because the four channels can drive two curtain inflators plus two seat-side airbag inflators from a single IC, lowering ECU cost and PCB area. The deploy current profile is programmable via SPI, allowing curtain and seat-side bags to use different pulse widths tuned to their respective inflator pyrotechnic loads. Automotive temperature range and wide-body SOIC package allow the IC to mount near the inflator connectors without thermal stress on the deploy FETs.
추천
Knee Airbag ECU
Knee airbag ECUs use the MCZ33797EKR2 when the platform consolidates knee airbag and pretensioner channels into a single driver board. The IC's four channels can drive two knee bags and two pretensioners, and per-channel diagnostics verify each initiator before deployment. Hardware handshaking on deploy initiation ensures deterministic timing even if the ECU SPI traffic is interrupted, which is critical because knee-bag deployment typically occurs within the same restraint event as the main frontal bags.
추천
Seat-Belt Pretensioner Module
Seat-belt pretensioner modules use individual squib channels of the MCZ33797EKR2 to fire pyrotechnic pretensioners on driver and passenger buckles. The IC's programmable deploy current and timer profiles allow the same hardware to drive both buckle pretensioners and anchor pretensioners with different pulse parameters. The onboard squib resistance measurement runs on every power-up, giving the ECU a continuous health check that meets ECE R16 pretensioner diagnostic requirements.
추천
Automotive Restraint Control Module
Centralized restraint control modules use the MCZ33797EKR2 to consolidate driver airbag, passenger airbag, side-curtain, and pretensioner channels into a single IC, reducing ECU cost and harness complexity. Four independent channels allow the module to support multiple restraint events within the same crash pulse. Automotive-qualified operation, integrated diagnostics, and SPI command interface let the module microcontroller run a single firmware image for the entire restraint system, simplifying software maintenance across vehicle platforms.
추천
엔지니어링 참조 데이터: MCZ33797EKR2 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MCZ33797EK |
|---|---|---|
| Package | 32-SOIC (0.295 inch, 7.50 mm) | 32-SOIC (0.295 inch, 7.50 mm) - same |
| Brand | NXP Semiconductors | NXP Semiconductors - same |
| Number of Channels | 4 | 4 - same |
| Packaging Media | Tape & Reel (TR) | Tube (non-reel) |
| Function | 4-Channel Squib Driver | 4-Channel Squib Driver - same |
| Diagnostics | Squib R, SCG, SCB, open-load | Squib R, SCG, SCB, open-load - same |
| Serial Interface | SPI-compatible | SPI-compatible - same |
| RoHS / Lead Free | Yes / Yes | Yes / Yes - same |
주요 차별점
- Four independent deployment channels in a single wide-body SOIC (vs MCZ33797EK)
- Integrated diagnostic analog front end (vs MCZ33797EK)
- NXP / Freescale automotive safety pedigree (vs MCZ33972AEW)
설계 노트
Airbag deployment energy is delivered from bulk capacitors charged to the deployment rail voltage, not directly from the vehicle battery. Estimated: for a typical 1.2 ms deploy pulse at 1.5-2.0 A per channel, a bank of low-ESR electrolytic or polymer capacitors in the 100-470 uF range is typical. The 32-SOIC package pins deploy high-side and low-side FET drains and sources per channel, so PCB copper pour area must be sized to carry the deploy current pulse without significant voltage drop.
Do not substitute a non-squib-driver IC (for example a multiple-switch detection interface like MCZ33972AEW) for the MCZ33797EKR2, even if the package is similar. Squib drivers have qualified deploy current profiles and dedicated diagnostic thresholds that are part of the OEM airbag ECU platform safety case; replacing the IC requires full re-qualification. Cross-reference only against same-family squib driver part numbers.
Squib driver PCB layout should keep the high-current deploy loop area as small as possible to minimize parasitic inductance, since inductance in the deploy loop can distort the deploy current waveform and risk incomplete inflator firing. Place the bulk energy-storage capacitors within 20-25 mm of the MCZ33797EKR2 deploy pins, use wide copper pours for the deploy return path, and isolate the analog diagnostic traces from the deploy traces to prevent noise coupling into the squib resistance measurement.
규정 준수 정보
RoHS compliance and Lead Free status confirmed from distributor listings. AEC-Q100 grade, REACH, halogen-free status, and conflict-minerals declaration must be verified from the manufacturer datasheet.
