MK22FN1M0AVLK12 - 120MHz Cortex-M4F 1MB Flash MCU | NXP (Tape & Reel)
부품 번호: MK22FN1M0AVLK12 ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $12.45 | $12.45 |
| 10 | $11.2 | $112.00 |
| 100 | $9.85 | $985.00 |
| 500 | $8.75 | $4,375.00 |
| 1,000 | $7.95 | $7,950.00 |
MK22FN1M0AVLK12 개요
A Kinetis K-series ARM Cortex-M4 microcontroller is a mainstream 32-bit MCU core built around the ARMv7-M architecture with optional single-precision floating-point unit, tightly-coupled memory, and a Nested Vectored Interrupt Controller. The K22 sub-family belongs to the broader Kinetis E/K/L/W portfolio and sits in the hierarchy of microcontroller -> 32-bit MCU -> ARM Cortex-M4 MCU -> Kinetis MCU, targeting performance-per-watt-sensitive applications such as USB peripherals, industrial control, and human-machine interfaces.
Key features include 120 MHz Cortex-M4 with FPU, 1 MB Flash, 128 KB SRAM, Full-Speed USB Host/Device/OTG with internal transceiver, a 16-bit ADC with up to 24 channels, low-power run, wait and stop modes with RTC, and a wide 1.71 V to 3.6 V supply range. The 80-LQFP package offers generous I/O count for industrial designs while remaining PCB-friendly at 12x12 mm, and the part is specified from -40 C to +105 C for industrial environments.
The MK22FN1M0 architecture combines an efficient Cortex-M4 pipeline with low-leakage process technology and a flexible low-power voltage-regulator block. The integrated Full-Speed USB physical layer eliminates external PHY cost and board area, and the on-chip Flash acceleration buffer delivers near-zero-wait-state performance across the 1 MB memory map, simplifying deterministic real-time firmware behavior.
Typical applications include Full-Speed USB peripherals (HID, CDC, mass storage), industrial motor and lighting controllers, portable medical instruments, consumer audio accessories, home automation bridges, and human-machine interface panels with TFT displays. Designers value the K22 for the combination of Cortex-M4 performance, generous memory, USB, and analog integration on a single die at industrial temperature grades.
When laying out the PCB, dedicate a continuous copper ground return under the QFP body, keep the VDD decoupling pair within 2 mm of the dedicated pins, and place the USB DP/DM traces at matched 90 ohm differential. For reliable USB enumeration, follow the reference manual's crystal-less recommendations or include a low-jitter external reference at the EXTRF pin.
This page synthesizes distributor pricing, Kinetis family drop-in alternatives, and practical design notes not found in the manufacturer datasheet, helping engineers evaluate the MK22FN1M0AVLK12 against its Kinetis siblings and competitive Cortex-M4 MCUs.
드롭인 대체품: MK22FN1M0AVLK12 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: MK22FN1M0AVLK12 (동일 폼 팩터 및 풋프린트).
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
이 제품에는 사용 가능한 드롭인 대체품이 없습니다.
대체품 요청MK22FN1M0AVLK12 최대 정격 & 전기적 특성
| Core | ARM Cortex-M4F with single-precision FPU |
| CPU Frequency (max) | 120 MHz |
| Program Flash | 1 MB (1M x 8) |
| SRAM | 128 KB |
| Supply Voltage Range | 1.71 V to 3.6 V |
| 동작 온도 | -40 C to +105 C |
| 패키지 | 80-LQFP (12x12 mm, pin-pitch 0.4 mm) |
| USB | USB 2.0 Full-Speed Host/Device/OTG with on-chip transceiver |
| ADC | 16-bit SAR ADC, multi-channel |
| DAC | 12-bit DAC |
| Communication Peripherals | UART, SPI, I2C, I2S |
| Timers | FlexTimer (FTM), PWM, PIT, RTC |
| Low-Power Modes | Run, Wait, Stop with RTC retention |
| 실장 유형 | Surface Mount |
| MSL Sensitivity | MSL3 (JEDEC J-STD-020) |
| Lead-Free / RoHS | Yes / RoHS-compliant |
| Series / Family | Kinetis K2x / K22 sub-family (K22F 120 MHz) |
MK22FN1M0AVLK12 핀 구성
| 핀 1 | PTE0 — GPIO, RTC_CLKOUT, CMP0_OUT, UART1_TX |
| 핀 2 | PTE1 — GPIO, RTC_ALARM, CMP0_IN3, UART1_RX |
| 핀 3 | PTE2 — GPIO, RTC_CLKOUT, ADC0_DP3, CMP2_OUT |
| 핀 4 | PTE3 — GPIO, RTC_ALARM, ADC0_DM3, CMP2_IN3 |
| 핀 5 | VDD — Supply voltage |
| 핀 6 | VSS — Ground |
| 핀 7 | PTE4 — GPIO, LPUART0_TX, I2C1_SCL, EWM_IN |
| 핀 8 | PTE5 — GPIO, LPUART0_RX, I2C1_SDA, EWM_OUT_b |
| 핀 9 | PTE6 — GPIO, LLWU_P7, CMP2_IN0, I2S0_MCLK |
| 핀 10 | PTE7 — GPIO, CMP2_IN1, UART3_TX, SPI1_SOUT |
| 핀 11 | PTH0 — GPIO, I2C0_SCL, CMP0_IN2, FT0_CH0 |
| 핀 12 | PTH1 — GPIO, I2C0_SDA, CMP0_IN3, FT0_CH1 |
| 핀 13 | VSS — Ground |
| 핀 14 | PTH2 — GPIO, I2C0_SCL, CMP0_IN4, SPI0_SCK |
| 핀 15 | PTH3 — GPIO, I2C0_SDA, CMP0_IN5, SPI0_SOUT |
| 핀 16 | PTH4 — GPIO, I2C0_SCL, FT0_CH4, SPI0_PCS0 |
| 핀 17 | PTH5 — GPIO, I2C0_SDA, FT0_CH5, SPI0_SIN |
| 핀 18 | PTH6 — GPIO, CMP0_IN6, FT0_CH6, I2C1_SDA |
| 핀 19 | PTH7 — GPIO, CMP0_IN7, CMP0_OUT, FT0_CH7 |
| 핀 20 | PTB0 — GPIO, ADC0_SE8, I2C0_SCL, FTM1_CH0 |
| 핀 21 | PTB1 — GPIO, ADC0_SE9, I2C0_SDA, FTM1_CH1 |
| 핀 22 | PTB2 — GPIO, ADC0_SE12, CMP0_IN0, FTM2_CH0 |
| 핀 23 | PTB3 — GPIO, ADC0_SE13, CMP0_IN1, FTM2_CH1 |
| 핀 24 | PTC0 — GPIO, ADC0_SE14, FTM0_CH0, EXTRF_IN |
| 핀 25 | PTC1 — GPIO, ADC0_SE15, FTM0_CH1, LLWU_P6 |
| 핀 26 | PTC2 — GPIO, CMP0_IN2, FTM0_CH2, I2C1_SCL |
| 핀 27 | PTC3 — GPIO, CMP0_IN3, FTM0_CH3, I2C1_SDA |
| 핀 28 | VLL1 — Core voltage decoupling (follow datasheet cap requirements) |
| 핀 29 | VDD — Supply voltage |
| 핀 30 | VSS — Ground |
| 핀 31 | PTC4 — GPIO, LLWU_P8, FTM0_CH4, CMP1_OUT |
| 핀 32 | PTC5 — GPIO, LLWU_P9, FTM0_CH5, CMP1_IN0 |
| 핀 33 | PTC6 — GPIO, CMP1_IN1, FTM0_CH6, I2S0_MCLK |
| 핀 34 | PTC7 — GPIO, CMP1_IN2, FTM0_CH7, I2S0_RXD0 |
| 핀 35 | PTD0 — GPIO, FTM3_CH0, SPI0_PCS0, I2C0_SCL |
| 핀 36 | PTD1 — GPIO, FTM3_CH1, SPI0_SCK, I2C0_SDA |
| 핀 37 | PTD2 — GPIO, FTM3_CH2, SPI0_SOUT, UART2_RX |
| 핀 38 | PTD3 — GPIO, FTM3_CH3, SPI0_SIN, UART2_TX |
| 핀 39 | PTD4 — GPIO, FTM3_CH4, SPI1_PCS0, FT0_CH4 |
| 핀 40 | PTD5 — GPIO, FTM3_CH5, SPI1_SCK, UART0_RX |
| 핀 41 | PTD6 — GPIO, FTM3_CH6, SPI1_SOUT, UART0_TX |
| 핀 42 | PTD7 — GPIO, FTM3_CH7, SPI1_SIN, CMP2_OUT |
| 핀 43 | PTA0 — GPIO, FTM0_CH0, UART0_CTS, JTAG_TCLK/SWD_CLK |
| 핀 44 | PTA1 — GPIO, FTM0_CH1, UART0_RTS, JTAG_TDI |
| 핀 45 | PTA2 — GPIO, FTM0_CH2, UART0_TX, JTAG_TDO/TRACESWO |
| 핀 46 | PTA3 — GPIO, FTM0_CH3, UART0_RX, JTAG_TMS/SWD_DIO |
| 핀 47 | PTA4 — GPIO, FTM0_CH4, CMP2_IN0, NMI_b |
| 핀 48 | PTA5 — GPIO, FTM0_CH5, CMP2_IN1, JTAG_TRST_b |
| 핀 49 | VDD — Supply voltage |
| 핀 50 | VSS — Ground |
| 핀 51 | PTF0 — GPIO, I2C0_SCL, FT0_CH0, UART3_RX |
| 핀 52 | PTF1 — GPIO, I2C0_SDA, FT0_CH1, UART3_TX |
| 핀 53 | PTF2 — GPIO, I2C1_SCL, ADC0_SE12, FT2_CH0 |
| 핀 54 | PTF3 — GPIO, I2C1_SDA, ADC0_SE13, FT2_CH1 |
| 핀 55 | PTF4 — GPIO, ADC0_SE14, FT2_CH2, LLWU_P14 |
| 핀 56 | PTF5 — GPIO, ADC0_SE15, FT2_CH3, CMP1_IN3 |
| 핀 57 | PTF6 — GPIO, CMP3_IN0, FT2_CH4, I2S0_RXD1 |
| 핀 58 | PTF7 — GPIO, CMP3_IN1, FT2_CH5, I2S0_TX_BCLK |
| 핀 59 | PTG0 — GPIO, I2C2_SCL, CMP3_IN2, FTM2_CH0 |
| 핀 60 | PTG1 — GPIO, I2C2_SDA, CMP3_OUT, FTM2_CH1 |
| 핀 61 | PTG2 — GPIO, I2C2_SCL, FTM4_CH0, SPI1_SCK |
| 핀 62 | PTG3 — GPIO, I2C2_SDA, FTM4_CH1, SPI1_SOUT |
| 핀 63 | PTG4 — GPIO, FT0_CH0, CMP0_IN3, SPI1_PCS0 |
| 핀 64 | PTG5 — GPIO, FT0_CH1, CMP0_IN4, SPI1_SIN |
| 핀 65 | PTG6 — GPIO, FT0_CH2, CMP0_IN5, FTM5_CH0 |
| 핀 66 | PTG7 — GPIO, FT0_CH3, CMP0_OUT, FTM5_CH1 |
| 핀 67 | USB0_DP — USB D+ data (Full-Speed, 90 ohm differential to DM) |
| 핀 68 | USB0_DM — USB D- data (Full-Speed, 90 ohm differential to DP) |
| 핀 69 | VDD — Supply voltage (USB supply tie-in) |
| 핀 70 | VSS — Ground |
| 핀 71 | USB_VBUS — USB VBUS sensing (5 V tolerant) |
| 핀 72 | DAC0_OUT — 12-bit DAC output |
| 핀 73 | ADC0_DP0 — ADC differential positive input 0 |
| 핀 74 | ADC0_DM0 — ADC differential negative input 0 |
| 핀 75 | VREFH — ADC/DAC reference high |
| 핀 76 | VREFL — ADC/DAC reference low (tie to VSS) |
| 핀 77 | ADC1_DP0 — ADC1 differential positive input 0 |
| 핀 78 | ADC1_DM0 — ADC1 differential negative input 0 |
| 핀 79 | NRST — Active-low reset (open-drain input, internal pull-up) |
| 핀 80 | PTB5 — GPIO, ADC0_SE10, FTM2_CH5, EXTRG_IN |
일반적인 애플리케이션
MK22FN1M0AVLK12 적합 용도: 6 애플리케이션s: USB HID / CDC Peripheral Devices, Industrial Motor and Lighting Control, Portable Medical and Wellness Devices, Consumer Audio Accessories (USB-C Audio), Smart Home / IoT Edge Hubs, Human-Machine Interface (HMI) Panels.
USB HID / CDC Peripheral Devices
The MK22FN1M0AVLK12's integrated Full-Speed USB 2.0 Host/Device/OTG controller with on-chip transceiver is the headline asset for USB peripherals. The 120 MHz Cortex-M4F core sustains 12 Mbps throughput with ample headroom for HID, CDC-ACM and DFU class stacks, while 1 MB Flash hosts the USB stack plus application firmware with room to spare. Placed as the sole MCU on the board, the part eliminates a ~$1 external PHY, and the crystal-less USB mode further reduces BOM. Compared to a Cortex-M0+ USB part, the Cortex-M4F delivers roughly 4x DMIPS/MHz, enabling faster HID report rates and on-board signal processing without a companion MCU.
추천
Industrial Motor and Lighting Control
With hardware FPU, FlexTimers, 16-bit ADC, and PWM outputs directly driving half-bridges, the MK22FN1M0AVLK12 is well suited for FOC motor control, BLDC pumps, and digital LED lighting. The Cortex-M4F executes sine/cosine transforms for FOC at 16 kHz switching frequency with roughly 30% CPU headroom, while the 1 MB Flash stores full BLDC/SMPS firmware plus lookup tables. Operating from -40 C to +105 C and 1.71 V-3.6 V, the part tolerates industrial 24 V bus transients via external DC-DC. Compared to a Cortex-M3, the FPU eliminates the need for soft-float math, which is typically 30x slower.
추천
Portable Medical and Wellness Devices
In portable medical and wellness devices - glucometers, pulse oximetry front-ends, electronic stethoscopes - the MK22FN1M0AVLK12 combines a 16-bit SAR ADC, 12-bit DAC, hardware FPU, and low-power run/wait/stop modes to maximize battery life while preserving signal integrity. The 1 MB Flash supports full DSP-style filtering (IIR/FIR for biosignal extraction), and the wide 1.71 V-3.6 V supply enables direct Li-ion cell connection. Stop+retention current stays in the low microamp range with RTC wake, supporting months of standby on a CR2032 coin cell.
추천
Consumer Audio Accessories (USB-C Audio)
USB-C audio dongles and USB headsets benefit from the MK22FN1M0AVLK12's Full-Speed USB with class-1 audio support, 12-bit DAC, and I2S interface for external codecs. The 120 MHz Cortex-M4F runs USB audio class 1.0/2.0 stacks, 48 kHz resampling, and basic noise suppression in one core, while the 1 MB Flash allows dual-mode USB stack plus codec configuration. Wide supply tolerance supports bus-powered 5 V designs after a single LDO.
추천
Smart Home / IoT Edge Hubs
The MK22FN1M0AVLK12 suits smart-home bridges and IoT edge controllers that aggregate Zigbee/Thread/BLE data over UART, SPI, or I2C peripherals. The Cortex-M4F processes parse/validate stages of common IoT protocols with the FPU accelerating JSON or Protobuf decoding, while 1 MB Flash supports OTA bootloader plus dual application slots. Industrial temperature rating allows deployment in unheated closets; integrated USB eases firmware provisioning and debugging via USB DFU.
추천
Human-Machine Interface (HMI) Panels
Color TFT HMI panels, appliance touchscreens, and industrial kiosks pair the MK22FN1M0AVLK12's 80-LQFP GPIO abundance with its 120 MHz Cortex-M4F to run LVGL/EmWin graphics and USB host for keyboards. The 1 MB Flash and 128 KB SRAM hold full bitmaps plus 24-bit color GUI assets, and the FPU accelerates rotation and alpha blending. The 12x12 mm package exposes five FlexTimer channels, two SPI, two I2C, three UART, and up to 60 GPIO to drive 320x240 WQVGA panels through SPI/8080 interfaces.
추천
추천 제품 요약
엔지니어링 참조 데이터: MK22FN1M0AVLK12 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MK22FN1M0AVLK12 | MK22FN1M0AVLL12 |
|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 80-LQFP (12x12 mm, VLK) | 80-LQFP (12x12 mm, VLK) - same | 100-LQFP (14x14 mm, VLL) - larger |
| Shipping Carrier | Tape & Reel (R) | Tray | Tape & Reel (R) |
| Core / Frequency | ARM Cortex-M4F / 120 MHz | ARM Cortex-M4F / 120 MHz | ARM Cortex-M4F / 120 MHz |
| Flash / SRAM | 1 MB / 128 KB | 1 MB / 128 KB | 1 MB / 128 KB |
| Supply Voltage | 1.71 V - 3.6 V | 1.71 V - 3.6 V | 1.71 V - 3.6 V |
| USB | FS USB Host/Device/OTG, on-chip PHY | FS USB Host/Device/OTG, on-chip PHY | FS USB Host/Device/OTG, on-chip PHY |
| Pin / Footprint | 80 LQFP, 0.4 mm pitch | 80 LQFP - drop-in | 100 LQFP - PCB rework required |
주요 차별점
- Same silicon, drop-in to MK22FN1M0AVLK12 tray variant (vs MK22FN1M0AVLK12)
- 100-LQFP upgrade option with same silicon (vs MK22FN1M0AVLL12)
- Integrated Full-Speed USB PHY (vs Cross-brand Cortex-M4 (e.g., STM32F407 without HS PHY))
설계 노트
Place the high-frequency 100 nF ceramic on each VDD/VSS pair within 2 mm of the pin and a bulk 4.7 uF ceramic on each VDD cluster. The K22 includes an internal linear regulator (VLL1); the datasheet mandates a 0.1 uF + 1 uF pair on the VLL1 pin - omitting the VLL1 capacitor causes reset faults under load transient. For USB bus-powered designs, add a 4.7 uF bulk on VBUS and a 1 M ohm voltage divider on USB_VBUS for accurate VBUS detection.
Route the USB DP/DM traces as a 90 ohm differential pair (8-10 mil trace, ~8 mil gap) on the top layer over a continuous ground return; avoid splitting ground under the pair. Place the MCU as close as physically possible to the USB connector to keep the stub below 4 mm. Match intra-pair length to within 150 mil to stay within USB compliance skew budget.
Estimated: at full 120 MHz operation with all peripherals enabled at 3.6 V, internal core current is roughly 30 mA (108 mW); the 80-LQFP theta_JA is around 60 C/W, giving a 6.5 C junction rise above ambient for typical industrial enclosures. No external heatsink is required. For environments above 70 C ambient or for applications that exercise the FPU continuously, derate to 120 MHz @ 3.0 V to lower dissipation approximately 30%.
Do not leave NRST floating during programming - the internal pull-up alone is too weak for noise environments; always place an external 10 k ohm pull-up plus a 1 nF to 10 nF to VSS for stable POR behavior. Do not exceed 3.6 V on any GPIO; the part is not 5 V tolerant. When using crystal-less USB, the EXTRF_IN pin must follow the reference manual recommendations; otherwise connect a 12 MHz crystal to EXTAL32/XTAL32.
규정 준수 정보
Industrial -40 C to +105 C grade. RoHS/REACH and lead-free per NXP product page. Not AEC-Q100 qualified - use S9KEAZN (Automotive KEA) or MK20 automotive parts for AEC-Q100 designs. The 'V' suffix in the ordering code indicates the wide-temp industrial grade.
