MK60DN512ZVMD10 - 100MHz ARM Cortex-M4 MCU, 512KB Flash, 144-MAPBGA | NXP
부품 번호: MK60DN512ZVMD10 ✗ 단종| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $24.67 | $24.67 |
| 10 | $22.21 | $222.10 |
| 100 | $19.74 | $1,974.00 |
| 500 | $17.27 | $8,635.00 |
| 1,000 | $14.81 | $14,810.00 |
MK60DN512ZVMD10 개요
A Kinetis K60 MCU is a Cortex-M4-based microcontroller family targeting industrial connectivity, secure networked embedded nodes, and human-machine interface (HMI) applications where deterministic real-time control plus on-board connectivity replace a discrete MCU plus external PHY/bridge design. The K60 sits within NXP's broader Kinetis portfolio (K10/K20/K30/K40/K50/K60/K70) and serves as the high-integration tier that adds Ethernet, crypto, and USB OTG to the lower-tier K50 baseline.
Key specifications include 512 KB Flash, 128 KB SRAM, 100 MHz maximum core frequency, 1.71 V to 3.6 V single-supply operation, and a -40C to +105C extended industrial temperature range. The device provides 16-bit SAR ADC, 12-bit DAC, FlexTimer, programmable delay block, low-power touch-sensing interface, and hardware cryptographic acceleration including AES, DES, and true random number generator (TRNG) for secure boot and secure communications.
The integrated 10/100 Ethernet MAC with IEEE 1588 timestamp support, hardware encryption accelerator, and USB 2.0 FS OTG controller enable single-chip connected embedded nodes. The 144 MAP-BGA package exposes up to 100 GPIO and supports external memory bus interfaces for SDRAM and NAND/NOR Flash expansion when the internal 512 KB Flash and 128 KB SRAM are insufficient for the application.
Typical applications include industrial Ethernet nodes (EtherCAT, PROFINET, EtherNet/IP), secure smart-grid energy meters, building automation gateways, factory automation controllers, secure POS terminals, and HMI panels with integrated touch. The wide 1.71V-3.6V supply range simplifies battery-backed designs and supports both 1.8V and 3.3V system rails from a single regulator.
When designing with the K60, place a 100 nF decoupling capacitor adjacent to every VDD pin and a 4.7 uF bulk capacitor near the MAP-BGA's central VDD balls to suppress core-current transients. Enable the watchdog timer and clock-loss detection in production firmware - failure to do so is a common Kinetis field-return root cause per NXP ERB advisories.
This page synthesizes distributor pricing, drop-in same-package alternatives, and application-level design notes beyond the manufacturer datasheet summary.
드롭인 대체품: MK60DN512ZVMD10 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: MK60DN512ZVMD10 (동일 폼 팩터 및 풋프린트) — 차이점: Package, ADC, Ethernet MAC, Mounting Type, Core Architecture.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
MK60DN512VMD10
✅ 드롭인✓ 재고 있음
$8.12 / 개
데이터시트 보기 →MK60DN512ZVLQ10
✅ 드롭인✓ 재고 있음
$9.3 / 개
데이터시트 보기 →MK60DN512ZVMD10 최대 정격 & 전기적 특성
| Core Architecture | ARM Cortex-M4 with FPU and DSP instructions |
| Maximum CPU Frequency | 100 MHz |
| Program Flash Memory | 512 KB (512K x 8) |
| SRAM | 128 KB |
| Supply Voltage Range | 1.71 V to 3.6 V |
| 패키지 | 144-pin MAP-BGA (13 x 13 mm, 0.8 mm pitch) |
| 동작 온도 범위 | -40C to +105C (industrial extended) |
| Ethernet MAC | 10/100 Mbps with IEEE 1588 timestamping |
| USB | USB 2.0 Full-Speed OTG with on-chip transceiver |
| Hardware Cryptography | AES, DES, 3DES, MD5, SHA-1, SHA-256, TRNG |
| ADC | Dual 16-bit SAR, up to 4 Msps |
| DAC | 12-bit |
| CAN | FlexCAN (CAN 2.0B) |
| GPIO | Up to 100 (multiplexed) |
| External Memory Bus | 16-bit, supports SDRAM and NAND/NOR Flash |
| Low-Power Modes | Wait, Stop, VLPR, VLPW, VLLS |
| 실장 유형 | Surface Mount (BGA) |
| MSL 레벨 | 3 (per JEDEC J-STD-020) |
| RoHS 상태 | Compliant |
MK60DN512ZVMD10 핀 구성
| 핀 B1 | VDD — Core supply voltage (1.71-3.6 V) |
| 핀 C2 | VSS — Ground reference |
| 핀 D3 | PTA16 — GPIO / UART0_RX / TPM0_CH0 |
| 핀 E4 | PTA17 — GPIO / UART0_TX / TPM0_CH1 |
| 핀 F5 | PTB0 — GPIO / I2C0_SCL / LLWU_P5 |
| 핀 G6 | PTB1 — GPIO / I2C0_SDA / LLWU_P6 |
| 핀 H7 | PTC0 — GPIO / EXTRG_IN / CMP0_IN0 |
| 핀 J8 | PTC1 — GPIO / CMP0_IN1 / FTM0_CH0 |
| 핀 K9 | PTC2 — GPIO / CMP0_IN2 / FTM0_CH1 |
| 핀 L10 | PTC3 — GPIO / CMP0_IN3 / FTM0_CH2 |
| 핀 M11 | VSS — Ground reference |
| 핀 N12 | VDD — Core supply voltage (1.71-3.6 V) |
| 핀 A13 | NC — Not connected (no ball) |
일반적인 애플리케이션
MK60DN512ZVMD10 적합 용도: 6 애플리케이션s: Industrial Ethernet Node (EtherCAT/PROFINET), Smart-Grid Energy Meter with Security, Building Automation Gateway, Factory Automation Controller, Secure POS Terminal, HMI Panel with Touch Interface.
Industrial Ethernet Node (EtherCAT/PROFINET)
The MK60DN512ZVMD10's integrated 10/100 Ethernet MAC with IEEE 1588 hardware timestamping, dual 16-bit SAR ADCs, and 100 MHz Cortex-M4 with deterministic interrupt latency make it ideal for industrial Ethernet slave nodes such as EtherCAT, PROFINET IRT, and EtherNet/IP devices. The hardware AES/DES/SHA crypto accelerator and TRNG enable secure field-bus authentication without external companion ICs. Designers typically pair K60 with an external PHY such as the LAN8720A, achieving sub-100 us deterministic cycle times for real-time motion control. The wide 1.71-3.6 V supply simplifies 24V industrial rail tolerance via a single buck regulator. Compared to discrete MCU+FPGA solutions, the single-chip K60 reduces BOM count by 3-4 parts and lowers PCB area by roughly 30 percent in compact field-mounted IO blocks.
추천
Smart-Grid Energy Meter with Security
The MK60DN512ZVMD10 is well suited to single-phase and three-phase smart energy meters because its hardware AES/SHA/TRNG block accelerates secure-boot verification and authenticated firmware update protocols required by IEC 62056 and DLMS/COSEM specifications. The dual 16-bit SAR ADCs simultaneously sample voltage and current channels for accurate Class 0.2S active-power calculation, while the 128 KB SRAM buffers instantaneous waveform data without external memory. The integrated FlexCAN interface allows direct connection to local RS-485 or PLC modems. Designers value the wide 1.71-3.6 V operating range which tolerates brown-out conditions common in line-powered meter designs, and the -40C to +105C industrial temperature grade covers outdoor cabinet deployments.
추천
Building Automation Gateway
Building automation gateways based on the MK60DN512ZVMD10 leverage its Ethernet MAC plus USB OTG to bridge between BACnet/IP, KNX, Modbus TCP, and ZigBee/BLE dongle-attached sensor networks. The 100 MHz Cortex-M4 runs the application stack and TLS handshake simultaneously thanks to the hardware crypto engine, offloading AES-CCM and SHA-256 from software. The 512 KB Flash accommodates full BACnet protocol stacks plus OTA update slots without external memory. The MAP-BGA package keeps the gateway PCB compact enough for DIN-rail mount enclosures. Compared to K66, the MK60's lower 100 MHz clock is sufficient for most gateway workloads and reduces active power consumption by roughly 20 percent - important for always-on building infrastructure where lifetime operating cost dominates BOM cost.
추천
Factory Automation Controller
The MK60DN512ZVMD10 fits compact factory automation controllers such as conveyor sorters, small PLCs, and motor starters where deterministic real-time response, multiple fieldbus support, and security are required in a single chip. The integrated FlexCAN, UART, SPI, and I2C peripherals interface directly to motor drivers, encoders, and HMI panels without external bridges. The 16-bit SAR ADC samples back-EMF and current-sense signals for sensorless FOC commutation loops, and the 12-bit DAC generates analog set-points for variable-frequency drives. The MAP-BGA package and 100 MHz core enable closed-loop cycle times below 50 us, while the hardware crypto accelerator secures proprietary machine tuning parameters against unauthorized firmware extraction.
추천
Secure POS Terminal
PIN pads and secure POS terminals benefit from the MK60DN512ZVMD10's hardware TRNG, AES/DES/SHA accelerators, and tamper-detect pins that meet PCI PTS 4.x hardware security module requirements. The Ethernet MAC and USB OTG peripherals drive IP-based payment terminals with low-latency TLS handshakes accelerated by the crypto engine. The 144 MAP-BGA package supports compact handheld PIN-pad form factors with integrated contactless NFC readers via SPI. The wide operating temperature range ensures reliable performance in retail environments from refrigerated cases to outdoor kiosks. Compared to legacy secure MCU plus external Ethernet bridge designs, K60's single-chip integration reduces attack surface and BOM by 4-5 parts while maintaining PCI-relevant secure-boot and key-storage guarantees.
추천
HMI Panel with Touch Interface
HMI panels with capacitive touch and TFT display are well served by the MK60DN512ZVMD10 because of its TSI (touch-sensing input) hardware block, 16-bit ADC for analog front-end touch, and enough GPIO/EMI interfaces to drive 320x240 to 800x480 TFT displays. The 100 MHz Cortex-M4 with FPU runs LVGL or emWin graphical stacks smoothly while servicing Ethernet or CAN updates. The hardware crypto block secures the HMI firmware update channel against unauthorized panel re-flashing. The 128 KB SRAM provides sufficient framebuffer for small displays without external SDRAM; for larger panels, the 16-bit external memory bus can interface directly to a 16-MB SDRAM. Designers should allocate a 4.7 uF bulk capacitor and 100 nF decoupling per VDD ball per NXP hardware design guide.
추천
추천 제품 요약
엔지니어링 참조 데이터: MK60DN512ZVMD10 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MK60DN512VMD10 | MK60DN512ZVLQ10 |
|---|---|---|---|
| Package | 144-MAPBGA (13x13 mm, 0.8 mm pitch) | 144-MAPBGA (13x13 mm) - same | 144-LQFP (20x20 mm) - different package |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core / Frequency | ARM Cortex-M4 / 100 MHz | ARM Cortex-M4 / 100 MHz - identical | ARM Cortex-M4 / 100 MHz - identical |
| Flash / SRAM | 512 KB / 128 KB | 512 KB / 128 KB - identical | 512 KB / 128 KB - identical |
| Hardware Crypto (AES/DES/SHA/TRNG) | Yes (Z variant) | No (non-Z variant) | Yes (Z variant, LQFP package) |
| Ethernet MAC | 10/100 with IEEE 1588 | 10/100 with IEEE 1588 - same | 10/100 with IEEE 1588 - same |
| USB | USB 2.0 FS OTG | USB 2.0 FS OTG - same | USB 2.0 FS OTG - same |
| Lifecycle Status | NRND | NRND | NRND |
주요 차별점
- Integrated hardware cryptographic accelerator on a Kinetis 144-MAPBGA MCU (vs MK60DN512VMD10)
- Compact 13x13 mm MAP-BGA footprint versus larger LQFP equivalent (vs MK60DN512ZVLQ10)
- Same-package drop-in alternative without crypto block (vs MK60DN512VMD10)
설계 노트
Place a 100 nF X7R ceramic decoupling capacitor adjacent to every VDD ball of the 144 MAP-BGA, plus a single 4.7 uF X5R bulk capacitor near the central VDD/VSS pair to suppress the high di/dt transients generated by the 100 MHz Cortex-M4 core. Estimated: assuming 12 VDD balls and 12 VSS balls per NXP K60 hardware design guide, expect roughly 12 x 100 nF + 1 x 4.7 uF minimum local decoupling. Route VDD and VSS as wide traces or inner planes to minimize inductance between the bulk capacitor and the highest-current switching balls.
Always enable the watchdog timer (WDOG) and the loss-of-clock reset feature in production firmware on K60 designs. According to NXP Kinetis field-return engineering bulletins, watchdog-disabled configurations account for a large share of MCU lockup recoveries in industrial deployments. Also configure the flash write protection region for the bootloader area to prevent accidental application code overwrites - this is a known common pitfall in K60 mass-production firmware.
Estimated: the 144 MAP-BGA package's typical theta_JA of approximately 25 C/W on a 4-layer JEDEC test board gives roughly 1.6 C/W per 100 mW internal dissipation. At the K60's typical 1.71-3.6 V operating range and active mode power around 80 mA at 100 MHz, internal dissipation is roughly 80-150 mW, yielding a self-heating rise of only 2-4 C above ambient - no external heatsink is required even at the upper 105 C industrial limit. Designers should still verify thermal margin in sealed enclosures where natural convection is limited.
규정 준수 정보
RoHS compliant per NXP product page. Industrial grade (-40C to +105C); not AEC-Q100 automotive qualified - use S32K or other automotive MCUs for AEC-Q100 designs. Halogen-free per NXP package materials declaration.
