MPXAZ4100AC6U - 20-105kPa Absolute Pressure Sensor | NXP
부품 번호: MPXAZ4100AC6U ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $8.5 | $8.50 |
| 10 | $7.65 | $76.50 |
| 100 | $6.8 | $680.00 |
| 500 | $6.05 | $3,025.00 |
| 1,000 | $5.45 | $5,450.00 |
MPXAZ4100AC6U 개요
An absolute pressure sensor measures pressure referenced to a sealed vacuum rather than to ambient atmosphere, distinguishing it from gauge or differential sensors. The MPXAZ4100A series belongs to the broader transducer family, which converts physical quantities (pressure, temperature, acceleration) into electrical signals. Absolute pressure sensors are essential wherever a known vacuum reference is required - most prominently in engine control units where manifold pressure directly correlates with air mass and load.
The MPXAZ4100AC6U integrates a single-chip MEMS piezoresistive bridge plus a custom ASIC that performs offset, span and temperature compensation. Media-resistant gel protects the die from harsh automotive intake environments, while the top-port 1/8" (3.17 mm) tube inlet accepts a vertical hose attachment typical of MAP installations. The ratiometric analog output simplifies ADC sampling with the same 5 V reference used by most engine ECUs.
Typical applications include automotive engine manifold absolute pressure (MAP) sensing, barometric pressure correction, HVAC pressure monitoring, and industrial pneumatic control. Its 0-85 °C compensated range with extended survivability to 125 °C allows under-hood placement.
Designers should route the analog output through an RC low-pass filter before ADC sampling to reject EMC events typical in automotive environments. Use a 100 nF decoupling capacitor close to the supply pin and ensure the hose inlet is oriented vertically to prevent condensate pooling that could damage the gel-protected die.
This page synthesizes distributor pricing, drop-in alternative MPXs, and application guidance that complements but is not a substitute for the manufacturer datasheet.
드롭인 대체품: MPXAZ4100AC6U — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: MPXAZ4100AC6U (동일 폼 팩터 및 풋프린트) — 차이점: Termination Style, Operating Pressure Range, Output Type, Accuracy, Package.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
MPXAZ4100A6U
✅ 드롭인✓ 재고 있음
$9.3 / 개
데이터시트 보기 →MPXA4100AC6U
✅ 드롭인✓ 재고 있음
$10.75 / 개
데이터시트 보기 →MPXAZ4100A6T1
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
MPXAZ4100AC6T1
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
MPXAZ4100AC6U 최대 정격 & 전기적 특성
| Pressure Type | Absolute |
| Operating Pressure Range | 2.9 PSI to 15.23 PSI (20 kPa to 105 kPa) |
| 출력 유형 | Analog Voltage (ratiometric) |
| 출력 전압 범위 | 0.3 V to 4.9 V |
| 공급 전압 | 4.85 V to 5.35 V |
| Port Style | Male 0.13 in (3.17 mm) Tube, Top Port |
| 패키지 / 케이스 | 8-SMD, Gull Wing, Top Port |
| Termination Style | Surface Mount (PCB) |
| 동작 온도 | -40 °C to +125 °C |
| Compensated Temperature | 0 °C to 85 °C |
| Mounting Feature | Surface Mount |
| 센서 유형 | Piezoresistive Silicon MEMS |
| Signal Conditioning | On-chip (amplified, calibrated, temperature-compensated) |
| Media Protection | Media-resistant gel |
| Automotive Qualified | Yes (engine control / MAP sensing) |
MPXAZ4100AC6U 핀 구성
| 핀 1 | Vs — Voltage supply (5 V nominal) |
| 핀 2 | GND — Ground |
| 핀 3 | Vout — Analog ratiometric output |
| 핀 4 | NC — Not connected (per datasheet) |
| 핀 5 | PAD — Mechanical / thermal pad |
| 핀 6 | PAD — Mechanical / thermal pad |
| 핀 7 | PAD — Mechanical / thermal pad |
| 핀 8 | PAD — Mechanical / thermal pad (port-side) |
일반적인 애플리케이션
MPXAZ4100AC6U 적합 용도: 6 애플리케이션s: Automotive Engine MAP Sensing, Barometric Pressure Correction, HVAC Refrigerant Line Monitoring, Industrial Pneumatic Control, Altitude / Barometric Data Loggers, Medical Respiratory Pressure Monitoring.
Automotive Engine MAP Sensing
The MPXAZ4100AC6U is the canonical NXP manifold absolute pressure sensor for port-fuel-injection and GDi engine control units. Its 20-105 kPa range maps cleanly onto intake pressures from wide-open-throttle vacuum to atmospheric boost, and the ratiometric 0.3-4.9 V output feeds directly into the ECU's 5 V ADC reference without level translation. The media-resistant gel protects the MEMS bridge from fuel vapor, oil aerosol and condensed moisture in the intake tract. The -40 to +125 °C operating envelope and AEC-qualified construction make it drop-in ready for under-hood ECU designs.
추천
Barometric Pressure Correction
The MPXAZ4100AC6U's 20-105 kPa absolute span and 0.3-4.9 V output provide a direct read of atmospheric pressure for barometric correction in motorcycle, scooter and small-engine ECUs. Its top-port 3.17 mm tube accepts a vented reference line routed to a static-air zone, and the on-chip temperature compensation holds accuracy across the 0-85 °C compensated band. Designers typically pair it with a separate intake MAP sensor and use the higher of the two readings as the barometric reference at key-on.
추천
HVAC Refrigerant Line Monitoring
In commercial HVAC systems the MPXAZ4100AC6U can monitor low-side refrigerant pressures where the absolute operating range overlaps with suction-line conditions (typically 50-100 kPa absolute for R-410A low side). Its small 8-SMD footprint fits inside the service-valve electronics module, and the ratiometric output simplifies sampling across varying supply rails. Designers should keep the gel-protected port away from direct liquid refrigerant exposure and use a vapor-side tap instead.
추천
Industrial Pneumatic Control
The MPXAZ4100AC6U suits low-pressure pneumatic systems operating between 20 kPa and 105 kPa absolute, such as vacuum-pick-and-place handlers, leak-test fixtures and clean-room pressure monitors. Its ratiometric analog output pairs with industrial 24-bit sigma-delta ADCs over a 0-5 V input range, and the on-chip calibration removes the need for system-level offset/span trim. The top-port hose inlet connects directly to 3.17 mm ID tubing common in pneumatic panels.
추천
Altitude / Barometric Data Loggers
Handheld barometric loggers, weather stations and drone altimeters can use the MPXAZ4100AC6U's 20-105 kPa range to resolve altitude from sea level to roughly 15,000 ft (≈57 kPa). The 0.3-4.9 V output gives ~46 mV/kPa sensitivity at 5 V supply, which after a 12-bit ADC yields about 2 Pa LSB - adequate for weather-barometric resolution. Designers should isolate the port from wind/Wake effects with a static-air baffle.
추천
Medical Respiratory Pressure Monitoring
Low-cost CPAP and spirometer reference designs use the MPXAZ4100AC6U as a secondary absolute pressure reference where a sealed vacuum reference is required for differential flow calculations. Its low 0.3 V zero-pressure offset and calibrated 4.9 V full-scale output simplify biopole evaluation. The media-resistant gel isolates the MEMS die from humidified breathing-circuit gas, an advantage over non-gel alternatives that fail under condensate exposure.
추천
추천 제품 요약
엔지니어링 참조 데이터: MPXAZ4100AC6U — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MPXAZ4100A6U | MPXA4100AC6U | MPXAZ4100A6T1 | MPXAZ4100AC6T1 |
|---|---|---|---|---|---|
| Package | 8-SMD, Gull Wing, Top Port | 8-SMD, Gull Wing, Top Port - same | 8-SMD, Gull Wing, Top Port - same | 8-SMD, Gull Wing, Top Port - same | 8-SMD, Gull Wing, Top Port - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Pressure Range | 20-105 kPa (2.9-15.23 PSI) | 20-105 kPa - identical | 20-105 kPa - identical | 20-105 kPa - identical | 20-105 kPa - identical |
| Output Voltage | 0.3 V to 4.9 V | 0.3 V to 4.9 V - identical | 0.3 V to 4.9 V - identical | 0.3 V to 4.9 V - identical | 0.3 V to 4.9 V - identical |
| Supply Voltage | 4.85 V to 5.35 V | 4.85 V to 5.35 V - identical | 4.85 V to 5.35 V - identical | 4.85 V to 5.35 V - identical | 4.85 V to 5.35 V - identical |
| Media-Resistant Gel | Yes (Z suffix) | Yes (Z suffix) - identical | No (gel-less) - differs | Yes (Z suffix) - identical | Yes (Z suffix) - identical |
| Packaging | Tube | Tube - identical | Tube - identical | Tape & Reel (T1) | Tape & Reel (T1) |
| Operating Temperature | -40 °C to +125 °C | -40 °C to +125 °C - identical | -40 °C to +125 °C - identical | -40 °C to +125 °C - identical | -40 °C to +125 °C - identical |
주요 차별점
- Media-resistant gel on same die/pinout (vs MPXA4100AC6U (gel-less))
- Drop-in compatibility with all MPXAZ4100A C6U variants (vs MPXAZ4100AC6T1)
- Tape-and-reel upgrade path within same family (vs MPXAZ4100A6U)
설계 노트
Place a 100 nF ceramic decoupling capacitor within 5 mm of the Vs pin (pin 1) and a bulk 1 µF tantalum or ceramic on the supply trace. Keep the analog output trace short and routed over a continuous ground plane to reject ECU switching noise. The exposed port-side pads (pins 5-8) must be soldered to a sufficiently large copper pour to provide mechanical stability against hose-induced stress.
Add a first-order RC low-pass filter (1 kΩ + 100 nF, fc ≈ 1.6 kHz) on Vout before the ADC to attenuate EMC events without materially affecting the 46 mV/kPa signal. Sample the ADC at >10× the filter cutoff and average 4-16 samples for stable MAP readings. Use the same 5 V rail as the ADC reference to leverage the ratiometric output of the MPXAZ4100AC6U and cancel supply-rail drift.
Do not use the gel-less MPXA4100AC6U in direct contact with intake gas or liquid media - moisture ingress will degrade the MEMS die. Always orient the top port vertically upward to prevent condensate pooling, and route the hose with a downward loop to divert liquid away from the sensor port. Exceeding the 5.35 V supply maximum will permanently damage the on-chip ASIC and shift output calibration.
Although the part is rated to +125 °C, the calibrated accuracy band is only 0-85 °C. For under-hood placement near exhaust manifolds, apply a heat sink or thermal barrier to keep the package within the compensated band; otherwise expect a few percent accuracy loss at extreme cold-crank or high-load conditions.
규정 준수 정보
AEC-Q100 qualified for engine control / automotive under-hood. RoHS/REACH/halogen/conflict-mineral data not present in the provided snippets and require cross-checking the NXP datasheet.
