MSP430F2617TPN - 16MHz Mixed-Signal MCU | Texas Instruments
부품 번호: MSP430F2617TPN ✓ 활성MSP430F2617TPN 개요
An MSP430 mixed-signal microcontroller integrates a low-power digital processing core with analog conversion resources and serial communication peripherals. In the power-management hierarchy, the MSP430 architecture is designed to support battery-operated and portable measurement applications. The MSP430F2617 combines a 16-bit RISC CPU, 16-bit registers, constant-memory processing features, and five low-power modes to balance measurement accuracy, response time, and energy efficiency.
Key features include a 16 MHz operating frequency, 92 KB Flash organized as 92K x 8 plus 256 bytes, and 8 KB of SRAM. The integrated 12-bit ADC supports analog measurement, while the dual 12-bit DACs provide two controllable analog outputs. I2C, SPI, and UART interfaces connect the device to sensors, transceivers, memory, and host systems. A hardware multiplier accelerates arithmetic operations, and DMA reduces CPU intervention during data transfers.
The device is intended for applications requiring more analog and serial resources than a basic MSP430 design, but without the memory and processing demands of a high-end application processor. Its 16-bit RISC architecture, on-chip DMA, and mix of ADC, DAC, and communication interfaces make it useful in industrial instrumentation, sensor acquisition, signal conditioning, and embedded control products.
Typical uses include portable measurement instruments, industrial sensor nodes, low-power data loggers, actuator controllers, and embedded laboratory equipment. For a new design, engineers should confirm the exact pin assignment, electrical limits, and recommended decoupling configuration against the Texas Instruments MSP430F2617 datasheet before layout release.
A particularly important design consideration is that the MCU’s low-power capability depends on correct peripheral clock configuration, sleep-mode entry, and board-level leakage control. Keep analog and digital return paths separated where possible, place the required bypass capacitors close to the supply pins, and validate the final noise performance with the actual sensor and communication circuitry.
This product page combines the confirmed MSP430F2617TPN specifications, package information, practical application guidance, and engineering-focused comparisons to support faster component selection and PCB design planning.
드롭인 대체품: MSP430F2617TPN — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: MSP430F2617TPN (동일 폼 팩터 및 풋프린트) — 차이점: ADC Resolution, CPU Architecture, Flash Memory, Hardware Multiplier, Low-Power Modes.
MSP430F2616TPN
✅ 드롭인가격 문의
데이터시트 보기 →MSP430F2417TPN
✅ 드롭인가격 문의
데이터시트 보기 →MSP430F2617TPN 최대 정격 & 전기적 특성
| CPU Architecture | 16-bit RISC |
| 최대 클록 주파수 | 16 MHz |
| Flash Memory | 92 KB (92K x 8 + 256 B) |
| SRAM | 8 KB |
| ADC Resolution | 12 bit |
| ADC Quantity | 1 |
| DAC Resolution | 12 bit |
| DAC Quantity | 2 |
| Serial Interfaces | I2C, SPI, UART |
| DMA | Yes |
| Hardware Multiplier | Yes |
| Low-Power Modes | 5 |
| 패키지 | 80-pin LQFP, 12 mm x 12 mm |
| 실장 유형 | Surface Mount |
MSP430F2617TPN 80-pin lqfp, 12 mm x 12 mm 핀 구성 가이드
MSP430F2617TPN(80-pin lqfp, 12 mm x 12 mm 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: MSP430F2617TPN.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
MSP430F2617TPN 적합 용도: 6 애플리케이션s: Portable Data Logger, Industrial Sensor Node, Precision Signal Conditioning, Laboratory Test Equipment, Actuator Control, Low-Power Embedded Control.
Portable Data Logger
The MSP430F2617TPN fits portable data loggers because its 16 MHz RISC core can process data while the five low-power modes support duty-cycled operation. The 92 KB Flash and 8 KB SRAM provide room for firmware, calibration tables, and buffered measurements. A 12-bit ADC supports sensor acquisition, while DMA helps transfer samples without tying the CPU to every register access. The 80-pin LQFP provides access to the device’s mixed-signal and serial resources. Battery life still depends on sensor load, active duration, standby leakage, and the chosen regulator, so validate the complete duty cycle rather than assuming a fixed runtime.
추천
Industrial Sensor Node
For industrial sensor nodes, the MSP430F2617TPN combines a 12-bit ADC, dual 12-bit DACs, and I2C, SPI, and UART interfaces in one 80-pin LQFP device. The ADC can acquire analog sensor signals, the DACs can provide controllable analog outputs, and the serial interfaces can connect local sensors or downstream controllers. The hardware multiplier and DMA support efficient signal processing and data movement. In an industrial enclosure, thermal conditions, grounding, isolation strategy, and communication robustness remain important because the MCU rating alone does not determine full-system accuracy or compliance.
추천
Precision Signal Conditioning
The MSP430F2617TPN is suitable for precision signal-conditioning products that require acquisition, control output, and configurable communications in a compact controller. The 12-bit ADC supports measurement channels, the dual 12-bit DACs can generate reference or excitation signals, and DMA can support repeatable sample movement. Its 16 MHz processing rate provides useful headroom for calibration and filtering while retaining the low-power characteristics of the MSP430 architecture. Board-level design should include clean analog grounding, careful reference routing, and measured filtering because converter performance in the finished product can be affected by source impedance, noise, and power-supply coupling.
추천
Laboratory Test Equipment
The MSP430F2617TPN can serve as the control core of compact laboratory instruments because it integrates a 16 MHz CPU, ADC, dual DACs, DMA, and multiple serial interfaces. The ADC can capture test or sensor waveforms, the DACs can generate stimulus signals, and UART or SPI can connect to a host or display subsystem. Its 92 KB Flash supports a substantial firmware image and calibration data, while 8 KB SRAM accommodates working buffers. Precision results depend on analog reference quality, layout symmetry, calibration, and the external measurement chain; use the manufacturer’s application guidance when developing precision timing or acquisition paths.
추천
Actuator Control
The MSP430F2617TPN fits actuator-control subsystems that need local analog output, sensor feedback, and serial coordination. The dual 12-bit DACs can create controllable setpoints or drive external analog stages, while the 12-bit ADC monitors feedback from a sensor. I2C and SPI support local peripheral access, and UART can carry supervisory commands. The controller’s five low-power modes can reduce consumption when the actuator is idle, although power-stage losses, driver topology, and protection requirements may dominate system consumption. Validate settling time, output range, and fault response together with the external driver circuitry.
추천
Low-Power Embedded Control
The MSP430F2617TPN is appropriate for embedded controllers where periodic sensing, computation, and communication must coexist with low standby consumption. Its 16-bit RISC core, hardware multiplier, DMA support, and five low-power modes provide a practical balance between throughput and energy use. The 80-pin LQFP exposes the analog and serial resources needed for a compact mixed-signal design. Firmware should use the device’s recommended idle and shutdown procedures, disable unused peripherals, and schedule conversion and serial activity carefully. Real battery-current measurements are essential because analog sensor bias, pull resistors, LEDs, regulators, and leakage outside the MCU can dominate total consumption.
추천
추천 제품 요약
엔지니어링 참조 데이터: MSP430F2617TPN — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MSP430F2616TPN | MSP430F2417TPN |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 80-LQFP (12x12) | 80-LQFP (12x12) | 80-LQFP (12x12) |
| Flash Memory | 92 KB (92K x 8 + 256 B) | 92 KB per cross-reference listing | 92 KB per cross-reference listing |
주요 차별점
- Integrated dual DAC capability (vs MSP430F2616TPN)
- Higher-memory mixed-signal integration (vs MSP430F2417TPN)
- Dedicated high-speed data movement (vs MSP430F2417TPN)
설계 노트
Use the Texas Instruments MSP430F2617 datasheet for the complete 80-pin LQFP footprint, pin assignments, and recommended decoupling network. Place required supply capacitors at the associated power pins with short, low-inductance traces, and route analog inputs away from digital clocks and switching nodes. Do not reuse a 64-pin LQFP land pattern because the TPN package has a different pin count and lead arrangement.
Separate analog and digital return paths as far as practical, provide a quiet ground reference for the ADC and DACs, and keep sensor traces away from high-current switching nodes. Verify reference-voltage stability and source impedance because converter accuracy can be affected by acquisition timing and external filtering. The dual 12-bit DAC outputs should be routed according to the manufacturer’s output-capacitance and stability guidance.
The MSP430 architecture can reduce consumption through its five low-power modes, but effective battery life depends on firmware and board behavior. Disable unused peripherals, control sensor bias current, and avoid keeping GPIO states that create static leakage paths. Measure average current across acquisition, processing, communication, and idle phases because the 16 MHz CPU may increase current while active.
Configure the 12-bit ADC for the required source impedance and acquisition time, and validate the resulting noise and linearity with the final sensor network. DMA can improve sample throughput and reduce CPU jitter, but buffer overruns or incorrectly programmed triggers can still corrupt captured data. Confirm peripheral clocks, trigger routing, and interrupt timing in the MSP430F2617 family user’s guide.
규정 준수 정보
Compliance status was not established in the cited product and distributor information. Use the current Texas Instruments product documentation and applicable declarations for production qualification.