ODIN-W260-06B - Dual-Band Wi-Fi + BT4.0 IoT Module | u-blox
부품 번호: ODIN-W260-06B ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $0 | $0.00 |
| 10 | $0 | $0.00 |
| 100 | $0 | $0.00 |
| 500 | $0 | $0.00 |
| 1,000 | $0 | $0.00 |
ODIN-W260-06B 개요
A wireless module is a complete, pre-certified radio subsystem that integrates the radio transceiver, baseband processor, RF front-end, and protocol stack onto a single footprint that a host MCU or processor communicates with over UART, SPI, or USB. Within the system hierarchy, the ODIN-W260-06B belongs to the IoT gateway connectivity layer: module -> wireless connectivity IC -> RF transceiver -> RF & wireless components. Because radio certification is performed at module level, using a module dramatically shortens time-to-market versus a discrete chipset design.
Key features include simultaneous dual-band Wi-Fi and Bluetooth operation from a single main antenna connector, u-blox u-connectXpress firmware enabling serial-to-Wi-Fi/BT bridging without RF firmware development, industrial-grade temperature performance for gateway deployments, and dual U.FL connectors allowing an external antenna pair for Wi-Fi MIMO diversity and Bluetooth. The -06B suffix denotes the u-connectXpress software variant with the B hardware revision.
The module is built on a powerful stand-alone multiradio architecture per the ODIN-W2 series datasheet (UBX-14039949, R25): an embedded processor runs the full TCP/IP and Bluetooth stack independently of the host, so the host simply sends AT commands or data frames. Dual-band 802.11n support enables 5 GHz operation, avoiding congested 2.4 GHz spectrum in factories with dense Wi-Fi and Bluetooth traffic.
Typical applications include industrial IoT gateways aggregating sensor networks to cloud services, building automation controllers, remote monitoring and telematics units, and asset-tracking systems where Wi-Fi backhaul and Bluetooth peripheral connectivity coexist.
Design consideration: since antennas are external via U.FL connectors, allocate PCB area near the module edge for the connectors and follow u-blox layout guidelines for ground-plane clearance to preserve RF performance; the module itself should not be reflowed more than the MSL 4 rating allows.
This page synthesizes distributor availability data, the manufacturer datasheet, and drop-in family alternatives plus practical design notes not found in the datasheet alone.
드롭인 대체품: ODIN-W260-06B — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
ODIN-W262-06B
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ODIN-W260-00B
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
ODIN-W260-03B
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
ODIN-W262-00B
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
ODIN-W262-03B
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
ODIN-W260-06B 사양
| Radio Protocols | Wi-Fi 802.11a/b/g/n, Bluetooth v4.0 + EDR |
| Frequency Bands | 2.4 GHz (2.4-2.5 GHz), 5 GHz (5.18-5.825 GHz) |
| Wi-Fi Standard | Dual-band 802.11a/b/g/n |
| Bluetooth Version | 4.0 + EDR |
| Antenna Type | Not included, external via 2x U.FL (W.FL) connector |
| Antenna Connectors | 2x U.FL, 50 ohm characteristic impedance |
| Main Antenna Function | Supports both Bluetooth and dual-band Wi-Fi |
| 실장 유형 | Surface Mount (SMD, castellated edges) |
| Firmware | u-connectXpress |
| Moisture Sensitivity Level | 4 |
| Peak Reflow Temperature | 245 C |
| Host Interfaces | UART, SPI, USB (per ODIN-W2 series datasheet) |
| Target Application | IoT gateway applications |
ODIN-W260-06B standard 핀 구성 가이드
ODIN-W260-06B(standard 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: ODIN-W260-06B.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
ODIN-W260-06B 적합 용도: 6 애플리케이션s: Industrial IoT Gateways, Building Automation Controllers, Remote Monitoring and Telematics, Asset Tracking Systems, Wireless Sensor-to-Cloud Bridges, Point-of-Sale and Retail IoT Devices.
Industrial IoT Gateways
The ODIN-W260-06B is purpose-built for IoT gateway applications per the u-blox ODIN-W2 datasheet. Its stand-alone multiradio processor runs the full TCP/IP, Wi-Fi, and Bluetooth stacks independently of the host MCU, so a low-power host controller can manage sensor aggregation via UART or SPI while the module handles all networking. Dual-band 802.11n support lets the gateway use the 5.18-5.825 GHz band to escape the congested 2.4 GHz spectrum typical of factories, while Bluetooth 4.0 + EDR enables local BLE sensor provisioning and diagnostics. The dual U.FL connectors allow separated antennas for Wi-Fi and BT, improving coexistence performance in dense RF environments. Expected benefit: reduced gateway BOM complexity and faster certification since radio regulatory approval is completed at module level.
추천
Building Automation Controllers
In building automation, controllers must bridge field devices to IT backbones over Wi-Fi while supporting Bluetooth-based commissioning tools. The ODIN-W260-06B fits because one module provides both radios concurrently: 802.11a/b/g/n over 2.4-2.5 GHz and 5.18-5.825 GHz for BMS cloud connectivity, and Bluetooth v4.0 + EDR for technician setup apps. The u-connectXpress firmware exposes AT commands, so legacy controller firmware only needs a serial driver rather than a network stack. Its castellated surface-mount pads allow assembly on standard reflow lines, and MSL 4 handling is routine for building-product manufacturers. Using an external antenna via the 50-ohm U.FL connector keeps the metal controller enclosure from detuning the radio, a common failure mode with PCB-antenna modules in wall-mounted enclosures.
추천
Remote Monitoring and Telematics
Remote monitoring units - pump stations, utility cabinets, cold-chain loggers - need dependable Wi-Fi backhaul plus local Bluetooth service access. The ODIN-W260-06B provides 2.4/5 GHz dual-band 802.11n for connection to whatever access point infrastructure exists on site, while Bluetooth 4.0 + EDR lets field technicians pull diagnostic data with a tablet without opening the enclosure. The stand-alone architecture keeps the network connection alive even if the host application processor reboots, since the module maintains the TCP/IP stack autonomously. External U.FL antennas can be routed to the enclosure exterior for maximum link margin across long distances to the nearest AP. Per datasheet UBX-14039949, the module is designed for exactly this class of stand-alone gateway product.
추천
Asset Tracking Systems
Asset trackers installed in warehouses and yards benefit from the ODIN-W260-06B's dual-radio design: Wi-Fi positioning can use received access-point identifiers across both the 2.4-2.5 GHz and 5.18-5.825 GHz bands for indoor location estimation, while Bluetooth 4.0 + EDR scans for BLE beacons attached to individual items. The module's stand-alone operation allows the tracker MCU to sleep between reporting intervals while the module buffers data. Because the radios use external U.FL antennas, tracker enclosures can be fully sealed for washdown environments without sacrificing RF performance. Integrators should budget for the MSL 4 moisture sensitivity during high-volume reflow assembly. Regulatory certification at the module level shortens approvals when deploying trackers across multiple regions.
추천
Wireless Sensor-to-Cloud Bridges
A common architecture pairs a low-power sub-GHz or wired sensor network with a Wi-Fi uplink; the ODIN-W260-06B serves as that uplink bridge. Its u-connectXpress firmware supports serial-to-Wi-Fi transparent mode, meaning sensor data arriving on the UART is forwarded over 802.11n TCP or UDP with no host stack development. Dual-band operation lets the bridge select whichever band the facility's WLAN provides, improving deployment flexibility. Bluetooth 4.0 + EDR adds a second channel for configuration tools or short-range beacon reception. The 50-ohm U.FL antenna connectors permit high-gain directional antennas for long outdoor links between buildings. Estimated benefit: weeks of firmware development saved compared with porting a TCP/IP stack onto a bare Wi-Fi chipset, based on the module's stand-alone design per UBX-14039949.
추천
Point-of-Sale and Retail IoT Devices
Retail peripherals such as price-label bases, kiosks, and payment terminals need reliable Wi-Fi plus Bluetooth for customer or staff smartphones. The ODIN-W260-06B delivers both: dual-band 802.11a/b/g/n for store WLANs (5 GHz reduces interference from dense customer-device traffic), and Bluetooth v4.0 + EDR for pairing flows. The stand-alone module architecture isolates payment-transaction networking from application bugs, since the module autonomously maintains connectivity. Castellated SMD mounting supports the compact two-layer carrier PCBs typical of retail hardware, and the external antenna interface allows antennas positioned to survive metal shelving environments. Per the ODIN-W2 datasheet, this gateway-class module is equally suited to compact connected endpoints.
추천
추천 제품 요약
엔지니어링 참조 데이터: ODIN-W260-06B — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | ODIN-W262-06B | ODIN-W260-00B | ODIN-W262-00B | ODIN-W260-03B | ODIN-W262-03B |
|---|---|---|---|---|---|---|
| Package | Castellated SMD module, 2x U.FL connectors | Castellated SMD module, 2x U.FL - same footprint | Castellated SMD module, 2x U.FL - same footprint | Castellated SMD module, 2x U.FL - same footprint | Castellated SMD module, 2x U.FL - same footprint | Castellated SMD module, 2x U.FL - same footprint |
| Brand | u-blox | u-blox | u-blox | u-blox | u-blox | u-blox |
| Bluetooth | Bluetooth v4.0 + EDR | Bluetooth v4.0 + EDR | Bluetooth v4.0 + EDR | Bluetooth v4.0 + EDR | Bluetooth v4.0 + EDR | Bluetooth v4.0 + EDR |
| Firmware | u-connectXpress (-06) | u-connectXpress (-06) | -00 firmware variant | -00 firmware variant | -03 firmware variant | -03 firmware variant |
| Antenna Interface | 2x U.FL (W.FL), 50 ohm, antenna not included | 2x U.FL - same | 2x U.FL - same | 2x U.FL - same | 2x U.FL - same | 2x U.FL - same |
| Primary Use Case | IoT gateway, dual-band Wi-Fi + BT with u-connectXpress | IoT gateway, alternate band configuration | IoT gateway, different software provisioning | IoT gateway, different band and software | IoT gateway, -03 software variant | IoT gateway, -03 software variant |
주요 차별점
- Ships with u-connectXpress AT-command firmware pre-installed (vs ODIN-W260-00B)
- Dual-band (2.4 + 5 GHz) operation for congested RF environments (vs ODIN-W262-00B)
- Shared main antenna for Wi-Fi and Bluetooth (vs ODIN-W262-06B)
설계 노트
Place the two U.FL connectors at the PCB edge with the module shield grounded to a continuous ground plane. Follow the land-pattern and layout guidelines in the ODIN-W2 series datasheet (UBX-14039949), keeping RF feed structures away from switching regulators. Route the UART/SPI host bus away from the antenna feed lines to prevent digital noise coupling into the 2.4/5 GHz receivers. Keep at least the datasheet-specified keep-out clearance around the castellated pads; do not route signals under the module shield.
The ODIN-W260-06B has Moisture Sensitivity Level 4 per distributor data. If the dry bag is opened and floor-life is exceeded, bake the module per the MSL 4 profile before reflow, otherwise moisture outgassing during the 245 C peak can cause delamination of the shield or substrate. Also verify the -06 firmware variant is what your host software expects - ordering the wrong -0X suffix yields a pin-identical module whose AT command set differs.
Wi-Fi transmit bursts draw significant pulsed current from the 3.3 V-class supply; provision low-ESR bulk capacitance (10 uF or more) near the module supply pads plus 100 nF decoupling per the u-blox design-in guidance in datasheet UBX-14039949. Estimated: undersized supply decoupling causes brownout resets during 802.11n TX at maximum power. Verify the exact peak current figure in the datasheet electrical characteristics before sizing your regulator.
When sharing the main U.FL antenna path between Bluetooth and dual-band Wi-Fi (as the module supports), select a dual-band 2.4/5 GHz antenna rated for both bands and verify 50-ohm matching across the full 2.4-2.5 GHz and 5.18-5.825 GHz range. Poor wideband matching degrades BT range first because BT receivers have the least link margin. Keep U.FL pigtail losses under 1 dB where possible; every dB lost at the antenna is a dB lost from link budget.
규정 준수 정보
Compliance declarations not present in the provided verified data; consult the u-blox product page and datasheet UBX-14039949 for official RoHS/REACH declarations. Radio regulatory certification is performed at module level per u-blox.
