OPA129UB - 1MHz Ultra-Low Bias Op Amp | Texas Instruments
부품 번호: OPA129UB ✗ 단종OPA129UB 개요
An operational amplifier is a high-gain analog amplifier used in feedback systems to amplify voltage differences with very high input impedance and low output impedance. The OPA129UB belongs to the voltage-feedback operational-amplifier hierarchy and can serve as an inverting amplifier, non-inverting amplifier, voltage follower, comparator in an open-loop circuit, or the active element in an instrumentation amplifier. Its defining role is signal conditioning rather than power conversion.
The main features of the OPA129UB include input bias current as low as 100 fA maximum, a 1 MHz gain-bandwidth product, a 2.5 V/µs slew rate, and operation from 10 V to 36 V. These characteristics support applications where the source impedance is high and amplifier input current could create an unwanted voltage error. A conventional precision bipolar-input amplifier may draw substantially more input current, whereas the OPA129UB's Difet input stage reduces that loading effect.
Its 8-pin SOIC implementation provides a standard surface-mount footprint and operates from dual positive and negative rails as well as a compatible single-supply arrangement within the stated supply limits. The 1 MHz bandwidth makes the device suitable for lower-frequency precision loops, sensor interfaces, photodiode amplifiers, and measurement front ends. The 2.5 V/µs slew rate also allows larger input signals to transition without requiring a much faster amplifier.
Typical applications include pH and electrochemical sensing, photodiode and optical-sensor amplification, high-impedance instrumentation, capacitive-sensor measurement, laboratory instrumentation, and precision current-to-voltage conversion. In these circuits, low input bias current helps preserve the integrity of weak source signals, while the 1 MHz bandwidth and 2.5 V/µs slew rate provide useful bandwidth for general instrumentation.
The primary design consideration is the unusually low input bias current. Board leakage, contamination, protective-diode leakage, and insufficient guarding around high-impedance nodes can become significant when the amplifier bias current is below 100 fA. Use short traces, clean insulating surfaces, and guarded input routes to prevent PCB contamination from degrading the measured signal.
This product record combines the OPA129UB's published operating characteristics with same-family replacement guidance and practical high-impedance layout advice. It is intended to help engineers identify the appropriate package, assess legacy availability, compare pin-compatible options, and plan laboratory or instrumentation designs without changing the PCB footprint unnecessarily.
드롭인 대체품: OPA129UB — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: OPA129UB (동일 폼 팩터 및 풋프린트) — 차이점: Amplifier Type, Gain-Bandwidth Product, Maximum Input Bias Current, Package, Slew Rate.
OPA129UBE4
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
OPA129UE4
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
OPA129UB 최대 정격 & 전기적 특성
| Amplifier Type | Single general-purpose operational amplifier |
| Number of Circuits | 1 circuit |
| Input Stage | Difet dielectrically isolated FET input |
| Maximum Input Bias Current | 100 fA |
| Typical Input Bias Current | 0.03 pA |
| Gain-Bandwidth Product | 1 MHz |
| Slew Rate | 2.5 V/µs |
| Minimum Total Supply Voltage | 10 V |
| Maximum Total Supply Voltage | 36 V |
| Nominal Positive and Negative Supply | ±18 V |
| 패키지 | 8-pin SOIC, 0.154 inch width (3.90 mm) |
| 실장 유형 | Surface mount |
| 핀 수 | 8 pins |
| Datasheet Page Count | 14 pages |
OPA129UB 8-pin soic, 0.154 inch width (3.90 mm) 핀 구성 가이드
OPA129UB(8-pin soic, 0.154 inch width (3.90 mm) 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: OPA129UB.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
OPA129UB 적합 용도: 6 애플리케이션s: High-Impedance Sensor Conditioning, Photodiode Signal Detection, Electrochemical Measurement Front End, Laboratory Instrumentation, Precision Current-to-Voltage Conversion, Capacitive Sensor Interface.
High-Impedance Sensor Conditioning
OPA129UB fits high-impedance sensor conditioning because its Difet input stage can reduce input bias current to as low as 100 fA. When the source impedance is high, amplifier bias current creates a signal-dependent voltage error that can obscure the sensor output. A practical circuit places the amplifier close to the sensor and uses a feedback network suited to the required gain. The 1 MHz gain-bandwidth product and 2.5 V/µs slew rate permit reasonable response speed, although layout cleanliness and guarding are essential when PCB leakage is comparable to the bias current.
추천
Photodiode Signal Detection
OPA129UB is appropriate for photodiode signal detection because photodiode currents are small and the amplifier input must contribute minimal bias-current error. Its 100 fA maximum input bias current helps preserve weak photocurrent information that could otherwise be lost across the feedback impedance. A transimpedance implementation can use the amplifier in an inverting configuration, but compensation must be selected for the photodiode capacitance. The 1 MHz bandwidth supports moderate-speed detection rather than the highest-rate optical receivers.
추천
Electrochemical Measurement Front End
OPA129UB suits electrochemical measurement front ends where the sensor presents a high source impedance and the useful output is a small current or voltage. Ultra-low bias current reduces excitation errors and improves the integrity of the measurement, while the 1 MHz bandwidth can support signals extending well beyond the slow DC region. The implementation should use guarded input nodes, low-contamination PCB materials, and careful separation between sensitive input traces and switching or digital circuitry. Supply headroom and output swing must be checked against the sensor operating range.
추천
Laboratory Instrumentation
OPA129UB can be used in laboratory instrumentation as a general-purpose precision front end for weak, high-impedance sources. The 10 V to 36 V total supply range supports traditional dual-rail laboratory architectures, and the 2.5 V/µs slew rate provides adequate response for many low-frequency measurements. Its ultra-low input bias current helps when the instrument connects to resistive dividers, probes, or sensors with leakage-sensitive impedances. Stable operation still depends on suitable feedback compensation and careful grounding of the measurement return path.
추천
Precision Current-to-Voltage Conversion
OPA129UB is useful in precision current-to-voltage conversion when the incoming current is very small and the feedback resistor is large. Because input bias current of up to 100 fA produces a much smaller error than in a conventional bipolar-input amplifier, the circuit can preserve more of the measured signal. The 1 MHz gain-bandwidth product supports useful closed-loop bandwidth, while the 2.5 V/µs slew rate handles output transitions. Resistor leakage, contamination, and stray capacitance should be controlled because they can otherwise dominate the performance of the measurement.
추천
Capacitive Sensor Interface
OPA129UB can form the active element of a capacitive-sensor interface when the sensor and feedback network have high impedance. The ultra-low bias current reduces unwanted charge injection at the input, and the 1 MHz bandwidth provides a practical operating range for many non-contact, capacitive, or proximity measurements. However, the high-impedance node makes stability sensitive to parasitic capacitance, so the compensation network and physical trace length require evaluation. Keep the sensitive input path short, guard it where practical, and verify stability with the complete sensor and cable assembly.
추천
추천 제품 요약
엔지니어링 참조 데이터: OPA129UB — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | OPA129UBE4 | OPA129UE4 |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Amplifier Type | General-purpose operational amplifier | Ultra-low-bias-current Difet operational amplifier | Ultra-low-bias-current Difet operational amplifier |
| Number of Circuits | 1 circuit | 1 circuit | 1 circuit |
| Gain-Bandwidth Product | 1 MHz | 1 MHz | 1 MHz |
| Slew Rate | 2.5 V/µs | 2.5 V/µs | 2.5 V/µs |
| Total Supply Voltage Range | 10 V to 36 V | 10 V to 36 V | 10 V to 36 V |
| Maximum Input Bias Current | 100 fA | 100 fA | 100 fA |
주요 차별점
- Ultra-low input bias current for high-impedance sources (vs OPA129UBE4)
- Same-family continuity with an 8-pin SOIC footprint (vs OPA129UE4)
- Adequate bandwidth and slew rate for precision instrumentation (vs OPA129UBE4)
설계 노트
Treat the OPA129UB input as a leakage-sensitive node. Keep input and feedback traces short, avoid exposed conductive contamination, and route a guard around the input where the amplifier configuration permits it. With maximum input bias current of 100 fA, PCB surface leakage and humidity can become comparable to the amplifier's own error. Do not route switching-regulator traces, high-impedance digital nets, or relay contacts near the sensitive input path.
Do not substitute a generic precision op amp solely because it fits an 8-pin SOIC outline. Confirm the pin assignment, input bias current, offset voltage, input noise, common-mode range, supply range, and stability with the actual gain and feedback values. A footprint match is not sufficient when the circuit depends on picoampere-level input current, because the alternative's input bias current may create an unacceptable offset.
Evaluate feedback compensation with the complete source impedance and any sensor or cable capacitance attached. The OPA129UB's 1 MHz gain-bandwidth product and 2.5 V/µs slew rate are useful for general instrumentation, but very high transimpedance gains can still require explicit noise-gain compensation. Check stability in both time and frequency domains, and keep sensitive nodes physically separated from fast-changing nodes to minimize capacitive feedthrough.
The OPA129UB operates from 10 V to 36 V total supply, so confirm the complete rail arrangement before designing the power subsystem. The 10 V figure applies across the supply terminals and does not mean that a 10 V single supply automatically provides the required input or output common-mode range. Use decoupling appropriate for the amplifier package and verify output swing, startup, and supply sequencing against the sensor's operating range.
규정 준수 정보
The available product information identifies the OPA129UB as obsolete but does not expose specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations.