OPA137UA - 36V, 1MHz FET-Input Op Amp | Texas Instruments
부품 번호: OPA137UA ✓ 활성OPA137UA 개요
A FET-input operational amplifier is an operational amplifier that uses field-effect transistors at its input. This input architecture provides very low bias current and high input impedance while preserving the voltage-feedback behavior expected by standard analog signal chains. The OPA137 belongs to the broader hierarchy of operational amplifier, analog amplifier, and semiconductor components used for amplification, filtering, buffering, and instrumentation.
Key characteristics include a 1 MHz gain-bandwidth product, ±10 pA typical input bias current, 120 µA typical quiescent current per channel, and 145 dB typical open-loop gain. Its input common-mode range extends to the positive supply, making the device practical in single-supply systems where the signal can approach the upper rail. The listed JLCPCB record also identifies 1.5 mV offset, 15 µV/°C temperature drift, 3.5 V/µs slew rate, 76 dB channel-separation behavior, and approximately 5 pA bias current for this ordering option.
The JFET input stage provides a practical balance between low noise, very high input impedance, and low supply current. Unlike bipolar-input operational amplifiers, it does not require substantial input bias current to operate. Its 1 MHz bandwidth is appropriate for audio-frequency measurement, transducers, and general-purpose precision analog signal chains, although it is not intended for high-speed video or RF signal paths. The 36 V maximum supply rating also allows operation from substantially higher rails than typical low-voltage amplifier families.
Typical uses include low-leakage current measurement, pH and electrochemical sensing, photodiode and other high-impedance sensor interfaces, precision filtering, and industrial instrumentation. In these applications, the OPA137UA can reduce loading of the sensor while preserving a 1 MHz signal bandwidth. It can also serve as a unity-gain buffer when the source presents limited DC bias current.
Layout should keep the input traces short and guard sensitive nodes from leakage and capacitive pickup. Place the bypass capacitor close to the positive-supply pin, maintain a low-impedance ground return, and provide adequate copper around the SOIC for stable thermal performance. Because the device is intended for low-bias operation, board contamination, flux residue, and moisture around high-impedance inputs can materially degrade practical input bias performance.
This product page combines the manufacturer specifications with package, application, lifecycle, sourcing, and drop-in replacement guidance. The comparison and design notes clarify where the OPA137UA is appropriate, what parameters matter when substituting an amplifier, and which circuit-level issues should be checked before production release.
드롭인 대체품: OPA137UA — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: OPA137UA (동일 폼 팩터 및 풋프린트) — 차이점: Package, Gain-Bandwidth Product, Amplifier Type, Input Bias Current, Input Common-Mode Range.
OPA131UJ
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
OPA137UA 최대 정격 & 전기적 특성
| Amplifier Type | Single FET-input operational amplifier |
| Number of Channels | 1 channel |
| Maximum Supply Voltage | 36 V |
| Gain-Bandwidth Product | 1 MHz |
| Input Common-Mode Range | Rail-to-rail to the positive supply |
| Typical Input Bias Current | ±10 pA |
| Listed Input Bias Current | 5 pA |
| Typical Quiescent Current | 120 µA per channel |
| Listed Quiescent Current | 220 µA |
| Typical Open-Loop Gain | 145 dB |
| Input Offset Voltage | 1.5 mV |
| Input Offset Voltage Temperature Drift | 15 µV/°C |
| Slew Rate | 3.5 V/µs |
| Channel Separation | 76 dB |
| Protection Features | Short-circuit protection and ESD protection |
| 패키지 | 8-SOIC, 0.154 in (3.90 mm) width |
| RoHS 상태 | RoHS compliant |
OPA137UA 핀 구성
| 핀 1 | NC — Not connected |
| 핀 2 | IN- — Inverting input |
| 핀 3 | IN+ — Non-inverting input |
| 핀 4 | V- — Negative supply |
| 핀 5 | NC — Not connected |
| 핀 6 | OUT — Output |
| 핀 7 | V+ — Positive supply |
| 핀 8 | NC — Not connected |
일반적인 애플리케이션
OPA137UA 적합 용도: 6 애플리케이션s: Precision pH and Electrochemical Sensing, Photodiode Signal Conditioning, Low-Leakage Current Measurement, Audio-Band Sensor Conditioning, Precision Filtering and Buffering, Industrial Instrumentation.
Precision pH and Electrochemical Sensing
The OPA137UA is appropriate for buffering electrochemical and pH-style sensors because its JFET input stage provides ±10 pA typical bias current, reducing measurement error caused by input loading. The sensor can connect near the amplifier input while the 1 MHz bandwidth preserves useful response through low-frequency sensor dynamics. Keep the high-impedance input traces short, clean, and separated from noisy power paths. A practical design should also account for input offset voltage, drift, electrode leakage, guard-ring techniques, and the output-swing limits of the selected supply voltage.
추천
Photodiode Signal Conditioning
The OPA137UA can serve as a transimpedance or input-buffer stage for photodiode signals because its low bias current avoids developing large error voltages across high-value feedback or bias resistors. Its 1 MHz bandwidth supports moderate-speed optical measurements without requiring the higher current of a conventional bipolar-input amplifier. The trade-off is that the 1.5 mV listed input offset and 15 µV/°C drift become important at high gain, so dark-current calibration and temperature compensation may be required.
추천
Low-Leakage Current Measurement
For precision current measurement, the OPA137UA's ±10 pA typical input bias current helps prevent the amplifier input from materially altering a microampere-level or picoampere-level sensing path. Its 1 MHz bandwidth is sufficient for many laboratory and industrial monitoring loops while its rail-to-rail-to-positive input range simplifies single-supply instrumentation. Validate leakage from PCB coatings, connectors, humidity, and nearby humidity-sensitive components because practical board-level contamination can exceed the amplifier's specified input current.
추천
Audio-Band Sensor Conditioning
The OPA137UA fits audio-frequency sensor conditioning, including microphone, audio transducer, and instrumentation preamplifier stages requiring very low input bias current. Its 1 MHz gain-bandwidth product supports signal bandwidth well beyond typical audio content, while the low quiescent current of 120 µA per channel is beneficial in portable equipment. The 36 V rating provides headroom for higher-voltage signal paths. Check capacitive-load stability and output-current requirements when driving long cables or unusually large feedback resistors.
추천
Precision Filtering and Buffering
The OPA137UA can implement active filters and unity-gain buffers when the source presents high impedance and the circuit needs low input loading. Its 145 dB typical open-loop gain supports accurate closed-loop gain, and the 1 MHz bandwidth is adequate for low-frequency measurement filters. At high noise gain, verify the gain-bandwidth, output-swing, and capacitive-stability limits in the manufacturer datasheet. Component tolerances and leakage in the feedback network may dominate actual filter accuracy.
추천
Industrial Instrumentation
OPA137UA is suitable for industrial measurement front ends that operate from higher supply voltages and interface with high-impedance transducers. The 36 V maximum supply rating is useful where sensor excitation and signal levels exceed low-voltage amplifier limits, while rail-to-rail input operation to the positive supply improves input-range utilization. Because industrial environments introduce leakage, humidity, surge, and EMI risks, use guarding, appropriate protection, clean board materials, and verified bypass-capacitor placement around the amplifier.
추천
엔지니어링 참조 데이터: OPA137UA — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | OPA131UJ |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 8-SOIC | 8-SOIC |
| Amplifier Type | Single FET-input operational amplifier | FET-input operational amplifier |
| Number of Channels | 1 channel | 1 channel |
| Gain-Bandwidth Product | 1 MHz | Approximately 1 MHz |
주요 차별점
- High-voltage low-bias input stage (vs OPA131UJ)
- Low-power precision operation (vs OPA131UJ)
- Single-supply input headroom (vs OPA131UJ)
설계 노트
Place the supply bypass capacitor immediately next to pin 7, and connect pin 4 to the ground or negative-supply return with a short, low-impedance path. Keep pins 2 and 3 away from switching nodes, inductors, and high-current return paths. Because the OPA137UA is designed for very low bias current, remove flux residue and avoid exposed leakage paths around the input pins.
Protect the high-impedance input stage with guarding when humidity, contamination, or long PCB traces could create leakage paths. A guard surrounding the input can be driven by a low-impedance copy of the input potential, reducing leakage without loading the source. Keep guarding geometry well away from the sensitive input itself, and test the assembled board because connector and coating leakage can dominate the amplifier's input-current specification.
Do not assume that pin compatibility guarantees identical noise, drift, output drive, or stability. Before substituting OPA131UJ for OPA137UA, compare the full datasheets for common-mode range, output swing, gain-bandwidth behavior, capacitive-load limits, input bias current, offset voltage, and temperature drift. Recheck the feedback network and decoupling after any substitution, especially in high-gain or high-noise-gain circuits.
규정 준수 정보
The JLCPCB product record identifies OPA137UA as RoHS compliant. No separate REACH, halogen-free, conflict-minerals, or automotive-qualification declaration is established here.