OPA2228P - Dual 33MHz Low-Noise Precision Op Amp | Texas Instruments
부품 번호: OPA2228P ✓ 활성OPA2228P 개요
An operational amplifier, or op amp, is a voltage-feedback amplifier that increases the voltage difference between its differential inputs. It belongs to the amplifier IC hierarchy, where precision amplifiers combine accurate DC behavior, low input offset voltage, high common-mode rejection, and low noise. The OPA2228 family combines those precision characteristics with wide bandwidth, making it suitable for instrumentation, signal conditioning, data acquisition, and analog control systems rather than only low-frequency reference circuits.
The OPA2228P's 3 nV/√Hz input-noise density is its central low-noise specification and is especially useful when the circuit must preserve small signals. Its 33 MHz gain-bandwidth product supports higher closed-loop bandwidth than a conventional precision amplifier, while the 11 V/µs slew rate allows large-signal transitions to occur quickly. The listed 138 dB CMRR helps reject common-mode interference, and the 5 µs settling time supports higher-throughput precision measurement systems.
The device contains two independent amplifiers in one 8-pin DIP package, reducing board area compared with two separate single-channel amplifiers. Voltage-feedback topology provides a familiar implementation model for non-inverting, inverting, summing, filtering, and current-feedback conversion circuits. Operation from ±2.5 V to ±18 V permits use with conventional dual supplies in laboratory and industrial equipment as well as lower-voltage bipolar rails where the signal range permits.
Typical uses include precision instrumentation front ends, low-level sensor signal conditioning, active filters, data-conversion input stages, audio and communication signal paths, and laboratory measurement equipment. In a current-to-voltage converter, low noise reduces the input-referred error introduced by the transducer. In an active filter, the wide bandwidth and fast slew rate preserve signal amplitude and phase margins. For high-gain DC measurement, CMRR and precision are more important than maximum bandwidth.
When laying out the OPA2228P, keep feedback components and sensitive input traces short, provide local supply bypassing, and maintain a quiet return path. Compensation values and noise-gain settings must be checked against the intended closed-loop bandwidth. Stable operation also depends on keeping the circuit within the device's electrical limits and considering load capacitance at the output.
This product record combines the manufacturer's device description with distributor package information, focused application analysis, design guidance, and a conservative drop-in comparison. It distinguishes confirmed OPA2228P characteristics from specifications that require confirmation in the complete Texas Instruments datasheet before precision design release.
드롭인 대체품: OPA2228P — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: OPA2228P (동일 폼 팩터 및 풋프린트) — 차이점: Amplifier Type, Package, Slew Rate.
OPA2228PG4
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
OPA2228P 최대 정격 & 전기적 특성
| Amplifier Type | Dual voltage-feedback operational amplifier |
| Number of Channels | 2 channels |
| Gain-Bandwidth Product | 33 MHz |
| Slew Rate | 11 V/µs |
| Input Noise Density | 3 nV/√Hz |
| Common-Mode Rejection Ratio | 138 dB |
| Settling Time | 5 µs |
| Supply Voltage Range | ±2.5 V to ±18 V |
| Total Supply Voltage Range | 5 V to 36 V |
| 패키지 | 8-pin DIP |
| 실장 유형 | Through-hole |
OPA2228P 8-pin dip 핀 구성 가이드
OPA2228P(8-pin dip 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: OPA2228P.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
OPA2228P 적합 용도: 8 애플리케이션s: Precision Instrumentation Front End, Low-Level Sensor Signal Conditioning, Active Analog Filters, Data Acquisition Input Stage, Laboratory Voltage Buffer, Audio and Communications Signal Path, Current-to-Voltage Conversion, Precision Control and Servo Loops.
Precision Instrumentation Front End
The OPA2228P suits precision instrumentation because it combines a 3 nV/√Hz input-noise density with 138 dB common-mode rejection and high-precision DC behavior. Two channels can condition complementary sensor outputs or support gain and filtering stages without using two separate packages. Its 33 MHz gain-bandwidth product also permits closed-loop bandwidth beyond very low-frequency precision-amplifier designs. In a practical front end, the amplifier gain, noise gain, biasing, and compensation must be selected together so that stability, output swing, and input common-mode range satisfy the actual sensor and supply conditions.
Low-Level Sensor Signal Conditioning
Low-level sensor signals benefit from the OPA2228P's 3 nV/√Hz noise density because amplifier input noise establishes a practical floor on the smallest recoverable signal. The 138 dB CMRR helps suppress common-mode voltage present on sensor wiring, while the fast 11 V/µs slew rate supports signals beyond the narrow bandwidth of many precision-only amplifiers. Use one channel for amplification and the second for filtering, buffering, or offset handling. Confirm the sensor output range, input bias current, input offset, and supply headroom before fixing the gain because those characteristics determine the usable accuracy of the complete measurement chain.
Active Analog Filters
The OPA2228P is appropriate for active filters that require low noise and more bandwidth than a conventional precision operational amplifier. Its 33 MHz gain-bandwidth product provides closed-loop bandwidth headroom, while the 11 V/µs slew rate helps maintain low distortion when the filter passes larger signals. The two channels can implement a second-order section or independent signal paths, such as a reconstruction filter and a separate anti-alias filter. Component tolerances and the amplifier's finite gain-bandwidth product affect the realized pole and stopband response, so simulation should include the intended gain, load, and supply rails.
Data Acquisition Input Stage
OPA2228P-based input stages can provide the low noise and high common-mode rejection needed when a precision converter captures small analog signals. A 3 nV/√Hz input-noise density reduces the amplifier contribution to measurement uncertainty, while 33 MHz bandwidth allows the amplifier to preserve the required signal spectrum and 5 µs settling behavior supports faster acquisition sequences. A practical design may use one channel as a gain stage and the other as an anti-alias or driver stage. Select the closed-loop gain and feedback network carefully, and confirm the ADC input range so the amplifier output swing remains usable under all input conditions.
Laboratory Voltage Buffer
The dual OPA2228P can serve as a laboratory voltage buffer when a source must be isolated from the following measurement stage without adding appreciable noise or common-mode error. The 138 dB CMRR, low input-noise density, and high-precision DC characteristics help preserve small signal integrity, while the wide bandwidth prevents the buffer from becoming the limiting element in moderate-frequency measurements. One channel may buffer the source and the other may provide gain or offset correction. Check output drive, capacitive-load stability, supply rails, and the required output swing because the basic bandwidth specification does not remove those implementation constraints.
Audio and Communications Signal Path
OPA2228P can be used in audio or communications circuitry when low-noise amplification and wideband transient response are both important. Its 3 nV/√Hz noise density supports quiet signal handling, while the 33 MHz gain-bandwidth product and 11 V/µs slew rate provide bandwidth beyond typical audio frequencies. The two channels can form balanced input stages, active filters, or line-level conditioning paths. Stable operation at the intended closed-loop gain remains essential, and the circuit should include appropriate input protection, output loading analysis, and supply bypassing. For high-fidelity audio, additional distortion and output-swing checks should be completed using the complete manufacturer documentation.
Current-to-Voltage Conversion
A current-to-voltage converter is a common use for a low-noise precision amplifier, and the OPA2228P's 3 nV/√Hz input-noise density helps reduce the equivalent input-current uncertainty introduced by the feedback network. The 138 dB CMRR can improve rejection of common-mode voltage on long or noisy sensor connections, while the dual package permits a second channel to provide gain, offset, or filtering. Design the feedback resistor carefully because its Johnson noise and parasitic capacitance affect both signal-to-noise ratio and stability. The complete design must also verify compliance with the amplifier's input common-mode range at the selected supply voltage and feedback gain.
Precision Control and Servo Loops
OPA2228P can support precision control loops that need low offset and low noise but also benefit from the 33 MHz bandwidth and 11 V/µs slew rate. The dual amplifier allows one channel to operate as the forward-path amplifier and the other as an auxiliary buffer, monitor, or feedback element. In servo systems, however, the amplifier's gain-bandwidth product must be considered together with sensor dynamics, compensation components, and loop delay. Simulate the complete loop for stability under expected load and supply variation, and keep output drive and capacitive-load limits in view when selecting the external compensation network.
엔지니어링 참조 데이터: OPA2228P — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | OPA2228PG4 |
|---|---|---|
| Package | 8-pin DIP | 8-pin DIP |
| Brand | Texas Instruments | Texas Instruments |
| Number of Channels | 2 channels | 2 channels |
주요 차별점
- Combines precision, low noise, and wide bandwidth in one dual amplifier (vs OPA2228PG4)
- Two independent amplifier channels reduce package count (vs OPA228P)
- Wide bandwidth for a precision amplifier family (vs OPA228P)
설계 노트
Route the two differential inputs, each output, and each power connection with short traces to reduce parasitic pickup and feedback-loop delay. Place the device where the through-hole DIP can be oriented to keep sensitive input nets away from switching nodes, relay contacts, and high-current return paths. For long sensor connections, use a grounded or properly referenced shield and assess input common-mode range before relying on the 138 dB CMRR figure.
The OPA2228P supports ±2.5 V to ±18 V, or 5 V to 36 V total, but the usable signal range is narrower than the absolute supply limits. Confirm input common-mode voltage and output swing for the selected rail pair at the highest expected load. Place local bypass capacitors close to the power pins and maintain a low-impedance return path so switching noise on the supply does not become additional input-referred error.
Do not treat the 33 MHz gain-bandwidth product as the closed-loop bandwidth at every gain. Higher noise gain or added feedback capacitance reduces bandwidth and can affect stability. Simulate the complete feedback network, including sensor capacitance, cable capacitance, load, and supply impedance, and verify settling against the 5 µs device specification only under the manufacturer's stated test conditions.
Use resistor isolation when driving capacitive loads, and keep the feedback network physically compact to minimize added phase lag. The 11 V/µs slew rate is valuable for large-signal steps, but excessive output capacitance or an aggressive noise gain can still produce ringing or instability. Measure the output with an appropriate probe and bandwidth limit, and compare the observed settling time with the circuit requirement rather than relying on the typical device figure alone.
규정 준수 정보
The available product and distributor descriptions do not explicitly confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status for the exact OPA2228P ordering code. Check the Texas Instruments product page and the compliance record associated with the selected package.