Texas Instruments

OPA2228P - Dual 33MHz Low-Noise Precision Op Amp | Texas Instruments

MPN: OPA2228P ✓ Hoạt động
±2.5 V to ±18 V Vdss 8-pin DIP Package
MOQ: 1 |

OPA2228P Tóm tắt

The Texas Instruments OPA2228P is a dual, wide-bandwidth, high-precision, low-noise operational amplifier with a 33 MHz gain-bandwidth product and an 11 V/µs slew rate, packaged in an 8-pin DIP. Its 3 nV/√Hz noise density, 138 dB common-mode rejection, and 5 µs settling time support applications that require both accurate DC measurement and wideband signal handling. The amplifier accepts supply voltages from ±2.5 V to ±18 V.

An operational amplifier, or op amp, is a voltage-feedback amplifier that increases the voltage difference between its differential inputs. It belongs to the amplifier IC hierarchy, where precision amplifiers combine accurate DC behavior, low input offset voltage, high common-mode rejection, and low noise. The OPA2228 family combines those precision characteristics with wide bandwidth, making it suitable for instrumentation, signal conditioning, data acquisition, and analog control systems rather than only low-frequency reference circuits.

The OPA2228P's 3 nV/√Hz input-noise density is its central low-noise specification and is especially useful when the circuit must preserve small signals. Its 33 MHz gain-bandwidth product supports higher closed-loop bandwidth than a conventional precision amplifier, while the 11 V/µs slew rate allows large-signal transitions to occur quickly. The listed 138 dB CMRR helps reject common-mode interference, and the 5 µs settling time supports higher-throughput precision measurement systems.

The device contains two independent amplifiers in one 8-pin DIP package, reducing board area compared with two separate single-channel amplifiers. Voltage-feedback topology provides a familiar implementation model for non-inverting, inverting, summing, filtering, and current-feedback conversion circuits. Operation from ±2.5 V to ±18 V permits use with conventional dual supplies in laboratory and industrial equipment as well as lower-voltage bipolar rails where the signal range permits.

Typical uses include precision instrumentation front ends, low-level sensor signal conditioning, active filters, data-conversion input stages, audio and communication signal paths, and laboratory measurement equipment. In a current-to-voltage converter, low noise reduces the input-referred error introduced by the transducer. In an active filter, the wide bandwidth and fast slew rate preserve signal amplitude and phase margins. For high-gain DC measurement, CMRR and precision are more important than maximum bandwidth.

When laying out the OPA2228P, keep feedback components and sensitive input traces short, provide local supply bypassing, and maintain a quiet return path. Compensation values and noise-gain settings must be checked against the intended closed-loop bandwidth. Stable operation also depends on keeping the circuit within the device's electrical limits and considering load capacitance at the output.

This product record combines the manufacturer's device description with distributor package information, focused application analysis, design guidance, and a conservative drop-in comparison. It distinguishes confirmed OPA2228P characteristics from specifications that require confirmation in the complete Texas Instruments datasheet before precision design release.

Bộ thay thế dễ dàng lắp đặt cho OPA2228P — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

Các biến thể trong loạt này

Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với OPA2228P (cùng hình factor và footprint) — khác nhau ở Amplifier Type, Package, Slew Rate.

Texas Instruments
Amplifier Type: Dual precision operational amplifier
Package: 8-pin PDIP (P)
Slew Rate: 10 V/µs
So sánh với OPA2228P →

OPA2228PG4

✅ Drop-In
📦 8-pin DIP
Same dual-amplifier device family and 8-pin DIP format; ordering packing code differs by 0% in the confirmed core amplifier parameters

📋 Tham chiếu thay thế (không có trong danh mục)

OPA2228P Tỷ lệ tối đa & tính chất điện

Amplifier Type Dual voltage-feedback operational amplifier
Number of Channels 2 channels
Gain-Bandwidth Product 33 MHz
Slew Rate 11 V/µs
Input Noise Density 3 nV/√Hz
Common-Mode Rejection Ratio 138 dB
Settling Time 5 µs
Supply Voltage Range ±2.5 V to ±18 V
Total Supply Voltage Range 5 V to 36 V
Hộp 8-pin DIP
Kiểu lắp đặt Through-hole

Hướng dẫn cấu hình chân OPA2228P 8-pin dip

Cấu hình chân cho OPA2228P (8-pin dip gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.

Bảng cấu hình chân 8-pin dip cho OPA2228P

Không có dữ liệu chân cụ thể sẵn có cho OPA2228P.

Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.

Ứng dụng tiêu biểu

OPA2228P phù hợp cho 8 Áp dụngs: Precision Instrumentation Front End, Low-Level Sensor Signal Conditioning, Active Analog Filters, Data Acquisition Input Stage, Laboratory Voltage Buffer, Audio and Communications Signal Path, Current-to-Voltage Conversion, Precision Control and Servo Loops.

🏭

Precision Instrumentation Front End

The OPA2228P suits precision instrumentation because it combines a 3 nV/√Hz input-noise density with 138 dB common-mode rejection and high-precision DC behavior. Two channels can condition complementary sensor outputs or support gain and filtering stages without using two separate packages. Its 33 MHz gain-bandwidth product also permits closed-loop bandwidth beyond very low-frequency precision-amplifier designs. In a practical front end, the amplifier gain, noise gain, biasing, and compensation must be selected together so that stability, output swing, and input common-mode range satisfy the actual sensor and supply conditions.

🧩

Low-Level Sensor Signal Conditioning

Low-level sensor signals benefit from the OPA2228P's 3 nV/√Hz noise density because amplifier input noise establishes a practical floor on the smallest recoverable signal. The 138 dB CMRR helps suppress common-mode voltage present on sensor wiring, while the fast 11 V/µs slew rate supports signals beyond the narrow bandwidth of many precision-only amplifiers. Use one channel for amplification and the second for filtering, buffering, or offset handling. Confirm the sensor output range, input bias current, input offset, and supply headroom before fixing the gain because those characteristics determine the usable accuracy of the complete measurement chain.

🌐

Active Analog Filters

The OPA2228P is appropriate for active filters that require low noise and more bandwidth than a conventional precision operational amplifier. Its 33 MHz gain-bandwidth product provides closed-loop bandwidth headroom, while the 11 V/µs slew rate helps maintain low distortion when the filter passes larger signals. The two channels can implement a second-order section or independent signal paths, such as a reconstruction filter and a separate anti-alias filter. Component tolerances and the amplifier's finite gain-bandwidth product affect the realized pole and stopband response, so simulation should include the intended gain, load, and supply rails.

📊

Data Acquisition Input Stage

OPA2228P-based input stages can provide the low noise and high common-mode rejection needed when a precision converter captures small analog signals. A 3 nV/√Hz input-noise density reduces the amplifier contribution to measurement uncertainty, while 33 MHz bandwidth allows the amplifier to preserve the required signal spectrum and 5 µs settling behavior supports faster acquisition sequences. A practical design may use one channel as a gain stage and the other as an anti-alias or driver stage. Select the closed-loop gain and feedback network carefully, and confirm the ADC input range so the amplifier output swing remains usable under all input conditions.

🔧

Laboratory Voltage Buffer

The dual OPA2228P can serve as a laboratory voltage buffer when a source must be isolated from the following measurement stage without adding appreciable noise or common-mode error. The 138 dB CMRR, low input-noise density, and high-precision DC characteristics help preserve small signal integrity, while the wide bandwidth prevents the buffer from becoming the limiting element in moderate-frequency measurements. One channel may buffer the source and the other may provide gain or offset correction. Check output drive, capacitive-load stability, supply rails, and the required output swing because the basic bandwidth specification does not remove those implementation constraints.

🎧

Audio and Communications Signal Path

OPA2228P can be used in audio or communications circuitry when low-noise amplification and wideband transient response are both important. Its 3 nV/√Hz noise density supports quiet signal handling, while the 33 MHz gain-bandwidth product and 11 V/µs slew rate provide bandwidth beyond typical audio frequencies. The two channels can form balanced input stages, active filters, or line-level conditioning paths. Stable operation at the intended closed-loop gain remains essential, and the circuit should include appropriate input protection, output loading analysis, and supply bypassing. For high-fidelity audio, additional distortion and output-swing checks should be completed using the complete manufacturer documentation.

⚡

Current-to-Voltage Conversion

A current-to-voltage converter is a common use for a low-noise precision amplifier, and the OPA2228P's 3 nV/√Hz input-noise density helps reduce the equivalent input-current uncertainty introduced by the feedback network. The 138 dB CMRR can improve rejection of common-mode voltage on long or noisy sensor connections, while the dual package permits a second channel to provide gain, offset, or filtering. Design the feedback resistor carefully because its Johnson noise and parasitic capacitance affect both signal-to-noise ratio and stability. The complete design must also verify compliance with the amplifier's input common-mode range at the selected supply voltage and feedback gain.

🏭

Precision Control and Servo Loops

OPA2228P can support precision control loops that need low offset and low noise but also benefit from the 33 MHz bandwidth and 11 V/µs slew rate. The dual amplifier allows one channel to operate as the forward-path amplifier and the other as an auxiliary buffer, monitor, or feedback element. In servo systems, however, the amplifier's gain-bandwidth product must be considered together with sensor dynamics, compensation components, and loop delay. Simulate the complete loop for stability under expected load and supply variation, and keep output drive and capacitive-load limits in view when selecting the external compensation network.

What is the OPA2228P?
The OPA2228P is a Texas Instruments dual operational amplifier combining low noise, wide bandwidth, and high precision. According to the Texas Instruments product page, it is a dual, wide-bandwidth, high-precision, low-noise amplifier, while distributor records identify the OPA2228P package as an 8-pin DIP. The device is intended for instrumentation and signal-conditioning circuits that require accurate DC performance as well as useful AC bandwidth.
What are the key specifications of OPA2228P that engineers should know?
The OPA2228P provides two amplifier channels in an 8-pin DIP, a 33 MHz gain-bandwidth product, an 11 V/µs slew rate, and a 3 nV/√Hz input-noise density. The Texas Instruments device description also identifies high precision and low noise as primary characteristics, while the listed specifications include 138 dB CMRR and a 5 µs settling time. These parameters make the device applicable to precision measurement and wideband analog signal conditioning.
What is the operating voltage range of OPA2228P?
The OPA2228P operates from ±2.5 V to ±18 V, corresponding to a total supply range of 5 V to 36 V. This range allows the dual amplifier to work with lower-voltage bipolar rails and conventional laboratory or industrial supplies. The Texas Instruments product page should be used as the controlling source for supply-current, absolute-maximum, and rail-to-rail operating details before final circuit design.
Where can I download the OPA2228P datasheet PDF?
The official OPA2228 datasheet and ordering information is available on the Texas Instruments product page at https://www.ti.com/product/OPA2228. That page provides manufacturer documentation, package options, and orderable part information for the OPA2228 family. Use the OPA2228P ordering designation to confirm that the selected package and temperature or packing options correspond to the required production configuration.
Where can I find the OPA2228P pinout?
The OPA2228P pinout must be taken from the pin-configuration diagram in the Texas Instruments OPA2228 datasheet because each dual amplifier in the 8-pin DIP has separate input, output, power, and biasing connections. The manufacturer product page is the official starting point for that document. Assign PCB connections from its package drawing and pin table rather than inferring an equivalent pin arrangement from another package in the OPA2228 family.
What is the noise density of OPA2228P?
The OPA2228P input-noise density is 3 nV/√Hz. According to the Texas Instruments OPA2228 documentation, this low-noise figure is paired with 138 dB common-mode rejection and a 5 µs settling time. The specification is particularly relevant when amplifying low-level sensor signals, because amplifier noise contributes directly to the smallest usable input voltage and therefore affects the circuit's achievable signal-to-noise ratio.
OPA2228P vs OPA2228PG4: which package should I choose?
Both OPA2228P and OPA2228PG4 are listed as dual amplifiers in 8-pin DIP packages. The distinguishing factor is the orderable packaging code rather than a change in the basic amplifier function. For PCB interchange, engineers should still verify the complete pin arrangement, temperature range, production packing method, and manufacturer ordering information in the OPA2228 datasheet before treating one MPN as a direct substitute for the other.
When should I choose OPA2228P over a lower-bandwidth precision op amp?
Choose the OPA2228P when the circuit needs both precision and substantially wider signal bandwidth. Its 33 MHz gain-bandwidth product and 11 V/µs slew rate provide more headroom than a conventional low-bandwidth precision amplifier, while its 3 nV/√Hz noise density and 138 dB CMRR support accurate low-level measurements. The trade-off is greater power and bandwidth than a deliberately narrow-band precision alternative.
Is OPA2228P suitable for low-level sensor signal conditioning?
Yes, the OPA2228P is suitable for many low-level sensor front ends because it combines 3 nV/√Hz input noise, 138 dB CMRR, and high-precision DC behavior. These characteristics reduce input-referred noise and common-mode interference in instrumentation circuits. The actual usable signal range also depends on sensor output, input offset, bias current, supply rails, and the chosen closed-loop gain, which must be checked against the complete datasheet.
What can replace OPA2228P in an existing design?
OPA2228PG4 is the closest identified same-package option because it is also a dual amplifier in an 8-pin DIP, but it should not be treated as an unconditional substitute without checking package dimensions, pinout, temperature grade, and production packing. The available cross-reference results did not identify five qualified drop-in replacements. Validate any candidate against the Texas Instruments OPA2228 datasheet and your circuit's noise, bandwidth, supply, and stability requirements.
Is there an equivalent OPA2228P from another manufacturer?
No cross-manufacturer drop-in equivalent was confirmed by the available substitution results. A functionally similar precision amplifier is not automatically a drop-in replacement because pin assignment, biasing, common-mode range, input-noise behavior, output drive, and stability can differ. Request a specific candidate for engineering review, then compare its 8-pin DIP pinout and electrical limits against the OPA2228P before approving it for an existing board.
Where to buy OPA2228P online?
Use the Request a Quote form on this page to request OPA2228P pricing, stock confirmation, and current lead time. The product is identified as an active dual, 8-pin DIP operational amplifier, but current commercial availability can change by package, quantity, and manufacturing condition. Share the exact MPN, target quantity, and required delivery date with the quote team to obtain the appropriate purchasing response.
What is the price of OPA2228P?
Current OPA2228P commercial pricing should be obtained through the Request a Quote form on this page rather than from a static listing value. The form can confirm unit cost, quantity breaks, stock status, and lead time for the exact 8-pin DIP ordering code. The archived catalog price retained for reference is not a live quotation and should not be treated as current availability or a firm order commitment.
What is the lead time for OPA2228P?
The current lead time for OPA2228P should be requested through the Request a Quote form on this page. Lead time can depend on order quantity, package configuration, stock position, and whether the requirement is for an authorized-channel order or another sourcing route. Provide the required quantity and target delivery date so the quote team can return a schedule tied to the requested configuration.
Is OPA2228P in stock?
Use the Request a Quote form on this page for current OPA2228P stock confirmation. A distributor landing page does not by itself establish that inventory is immediately available, particularly when the desired package, quantity, or shipping destination is specified. The quote team can check the exact OPA2228P ordering code and respond with current availability, lead time, and any minimum-order requirements.
How is OPA2228P different from OPA228P?
The OPA2228P contains two amplifier channels in one 8-pin DIP, whereas the OPA228P is identified in the comparison result as a single-amplifier 8-pin DIP device. Consequently, OPA228P is not a pin-for-pin drop-in replacement for a dual-amplifier OPA2228P circuit. The OPA2228P should be selected when two independent precision amplifier functions share the package, and OPA228P may be considered only for a redesigned single-channel position.
Does OPA2228P comply with RoHS and REACH?
The RoHS and REACH status of the exact OPA2228P ordering code must be confirmed in the Texas Instruments product documentation or the distributor compliance record for that MPN. The manufacturer product page at https://www.ti.com/product/OPA2228 is the appropriate official reference for material-composition and environmental declarations. Do not infer compliance for a production order solely from the family name or from another OPA2228 package variant.

Dữ liệu tham khảo kỹ thuật cho OPA2228P — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose the OPA2228P when a design needs two precision amplifier channels, low input noise, and substantially more bandwidth than a conventional DC-only precision amplifier. Its confirmed 3 nV/√Hz noise density, 138 dB CMRR, 33 MHz gain-bandwidth product, and 11 V/µs slew rate make it appropriate for instrumentation, sensor conditioning, active filtering, and data-acquisition input stages. OPA2228PG4 is the closest identified same-package ordering alternative and may fit where only the production packing code differs. OPA228P should be considered only for a single-channel position because it is not a dual-amplifier substitute. For final selection, verify the complete pinout, temperature range, electrical limits, and stability in the manufacturer datasheet, especially when replacing an existing OPA2228P without changing the PCB.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này OPA2228PG4
Package 8-pin DIP 8-pin DIP
Brand Texas Instruments Texas Instruments
Number of Channels 2 channels 2 channels

Bảo phân biệt quan trọng

  • Combines precision, low noise, and wide bandwidth in one dual amplifier (vsOPA2228PG4)
  • Two independent amplifier channels reduce package count (vsOPA228P)
  • Wide bandwidth for a precision amplifier family (vsOPA228P)

Ghi chú thiết kế

Route the two differential inputs, each output, and each power connection with short traces to reduce parasitic pickup and feedback-loop delay. Place the device where the through-hole DIP can be oriented to keep sensitive input nets away from switching nodes, relay contacts, and high-current return paths. For long sensor connections, use a grounded or properly referenced shield and assess input common-mode range before relying on the 138 dB CMRR figure.

The OPA2228P supports ±2.5 V to ±18 V, or 5 V to 36 V total, but the usable signal range is narrower than the absolute supply limits. Confirm input common-mode voltage and output swing for the selected rail pair at the highest expected load. Place local bypass capacitors close to the power pins and maintain a low-impedance return path so switching noise on the supply does not become additional input-referred error.

Do not treat the 33 MHz gain-bandwidth product as the closed-loop bandwidth at every gain. Higher noise gain or added feedback capacitance reduces bandwidth and can affect stability. Simulate the complete feedback network, including sensor capacitance, cable capacitance, load, and supply impedance, and verify settling against the 5 µs device specification only under the manufacturer's stated test conditions.

Use resistor isolation when driving capacitive loads, and keep the feedback network physically compact to minimize added phase lag. The 11 V/µs slew rate is valuable for large-signal steps, but excessive output capacitance or an aggressive noise gain can still produce ringing or instability. Measure the output with an appropriate probe and bandwidth limit, and compare the observed settling time with the circuit requirement rather than relying on the typical device figure alone.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

The available product and distributor descriptions do not explicitly confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status for the exact OPA2228P ordering code. Check the Texas Instruments product page and the compliance record associated with the selected package.

Tìm kiếm liên quan

OPA2228P datasheet OPA2228P pinout OPA2228P datasheet pdf OPA2228P specifications OPA2228P 8-pin DIP OPA2228P noise density OPA2228P gain bandwidth OPA2228P replacement OPA2228P equivalent OPA2228P vs OPA228P OPA2228P vs OPA2228PG4 Texas Instruments OPA2228P OPA2228P price OPA2228P stock OPA2228P application circuit

Các bộ phận và thuật ngữ liên quan

Texas Instruments OPA2228P OPA2228PG4 OPA228P dual operational amplifier voltage-feedback amplifier precision amplifier amplifier IC semiconductor low-noise amplifier 3 nV/√Hz noise density 33 MHz gain-bandwidth product 11 V/µs slew rate 138 dB CMRR 5 µs settling time 8-pin DIP through-hole package sensor signal conditioning active filter data acquisition current-to-voltage conversion precision instrumentation power supply rejection input offset voltage
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ