OPA27GU - Ultra-Low-Noise Precision Op Amp | Texas Instruments
부품 번호: OPA27GU ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $3.08 | $3.08 |
| 10 | $3.08 | $30.80 |
| 100 | $3.08 | $308.00 |
| 500 | $3.08 | $1,540.00 |
| 1,000 | $3.08 | $3,080.00 |
OPA27GU 개요
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. Precision operational amplifiers add low offset, low drift, high open-loop gain, and strong common-mode and power-supply rejection. The OPA27 belongs to the operational-amplifier hierarchy, which sits within analog ICs and broader semiconductor signal-conditioning systems.
Key features include 4.5 nV/√Hz maximum noise at 1 kHz, 100 µV maximum offset voltage, 0.4 µV/°C maximum input offset drift, 117 dB minimum open-loop gain, 100 dB minimum common-mode rejection, and 94 dB minimum power-supply rejection. Its unity-gain stability supports direct use as a non-inverting buffer, while the precision architecture is useful for low-level sensor and instrumentation signals.
The OPA27GU uses an 8-SOIC package and is identified by DigiKey as a single-circuit standard general-purpose amplifier. The verified part data also associates the family with operation from -40°C to +85°C and an 8 MHz gain-bandwidth product. These characteristics make the device suitable for audio preamplifiers, sensor interfaces, precision filters, measurement front ends, and low-noise analog signal chains.
Designers should verify the complete supply-voltage range, input common-mode limits, output swing, bias current, and stability requirements in the manufacturer datasheet before final circuit release. Decoupling capacitors should be placed close to the supply pins, and the PCB should minimize parasitic capacitance and feedback-loop coupling. The low-noise benefit is realized only when the surrounding resistors, references, layout, and signal source do not dominate the system noise.
This page combines verified manufacturer and distributor information with practical selection, application, and design guidance. It distinguishes the OPA27GU from broader OP27-family alternatives and identifies where a footprint-compatible replacement requires confirmation of electrical and pin-level details before substitution.
드롭인 대체품: OPA27GU — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: OPA27GU (동일 폼 팩터 및 풋프린트) — 차이점: Operating Temperature Range, Package, Supply Voltage Range, Mounting Type, Gain-Bandwidth Product.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
OPA37GU
✅ 드롭인✓ 재고 있음
가격 문의
데이터시트 보기 →OPA2277UA
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$2.95 / 개
데이터시트 보기 →OPA227UA
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
OP07AZ/883
✅ 드롭인✓ 재고 있음
$7.9 / 개
데이터시트 보기 →OP27AJ/883C
✅ 드롭인✓ 재고 있음
$29.8 / 개
데이터시트 보기 →OPA27GU 최대 정격 & 전기적 특성
| Product Type | Ultra-low-noise precision operational amplifier |
| Input Noise | 4.5 nV/√Hz maximum at 1 kHz |
| Offset Voltage | 100 µV maximum |
| Input Offset Drift | 0.4 µV/°C maximum |
| Open-Loop Gain | 117 dB minimum |
| Common-Mode Rejection | 100 dB minimum |
| Power-Supply Rejection | 94 dB minimum |
| Gain-Bandwidth Product | 8 MHz |
| Gain Stability | Unity-gain stable |
| 동작 온도 범위 | -40°C to +85°C |
| 패키지 | 8-pin SOIC |
| Number of Circuits | 1 amplifier |
| 실장 유형 | Surface mount |
| Product Classification | Standard general-purpose amplifier |
| Manufacturer | Texas Instruments |
| Datasheet Availability | Manufacturer product page and datasheet available |
OPA27GU 8-pin soic 핀 구성 가이드
OPA27GU(8-pin soic 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: OPA27GU.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
OPA27GU 적합 용도: 6 애플리케이션s: Precision Audio Preamplifier, Low-Level Sensor Signal Conditioning, Precision Instrumentation Amplifier, Active Audio Filter, Precision Reference Buffer, Low-Noise Voltage Amplifier.
Precision Audio Preamplifier
The OPA27GU fits low-level audio preamplification because its verified input noise is 4.5 nV/√Hz maximum at 1 kHz and its unity-gain stability supports direct buffering. Place it near the microphone or line-input source, use low-noise feedback resistors, and bypass the supply pins close to the IC. The amplifier can provide low-voltage-noise amplification for audio signals, while the final system noise remains dependent on source impedance, resistor noise, bandwidth, and gain configuration.
추천
Low-Level Sensor Signal Conditioning
The OPA27GU is appropriate for amplifying weak sensor signals where input-referred noise and offset can affect measurement resolution. Its verified 100 µV maximum offset and 0.4 µV/°C maximum drift provide useful DC precision, while 4.5 nV/√Hz maximum noise supports low-noise amplification. The circuit should use a sensor-specific input filter, defined gain, local decoupling, and careful grounding to prevent switch-mode and digital circuitry from corrupting the measurement.
추천
Precision Instrumentation Amplifier
The OPA27GU can serve as a core amplifier in precision instrumentation when the design needs low noise, high open-loop gain, and good rejection of common-mode and supply variations. The verified specifications include 117 dB minimum open-loop gain, 100 dB minimum common-mode rejection, and 94 dB minimum power-supply rejection. A practical implementation should verify resistor matching, gain-bandwidth behavior, input bias current, and output-headroom requirements for the selected sensor and measurement bandwidth.
추천
Active Audio Filter
The OPA27GU is useful in low-noise active filter stages where signal amplitude is small and component noise can affect the filter response. Its 8 MHz gain-bandwidth product provides bandwidth headroom for moderate-frequency filter designs, while the verified 4.5 nV/√Hz maximum input noise supports low-noise amplification. Select resistor and capacitor tolerances carefully, check phase margin and stability at the intended gain, and keep sensitive filter nodes away from switching regulators and digital return currents.
추천
Precision Reference Buffer
OPA27GU can buffer a low-level reference or drive a precision measurement input when the source requires low noise and low offset drift. The verified 100 µV maximum offset and 0.4 µV/°C maximum drift are important because reference-buffer errors can directly appear at the ADC or sensor input. Confirm the reference voltage range, output-current capability, capacitive-load stability, and settling requirements in the datasheet before using the amplifier outside laboratory-level conditions.
추천
Low-Noise Voltage Amplifier
The OPA27GU is appropriate for general low-level voltage amplification in laboratory, industrial, and audio-adjacent signal chains. Its verified high open-loop gain, 100 dB minimum common-mode rejection, and 94 dB minimum power-supply rejection help preserve small differential signals when the circuit is properly configured. The implementation should include input protection, defined gain-setting resistors, supply filtering, and an output-stage check so that the amplifier’s precision is not lost through clipping, loading, or instability.
추천
추천 제품 요약
엔지니어링 참조 데이터: OPA27GU — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | OPA37GU | OPA2277UA | OPA227UA | OP07 | OP27 |
|---|---|---|---|---|---|---|
| Package | 8-SOIC | 8-SOIC candidate; confirm exact suffix | 8-SOIC candidate; confirm exact suffix | 8-SOIC candidate; confirm exact suffix | 8-SOIC candidate; confirm pinout | 8-SOIC candidate; confirm pinout |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Analog Devices | Analog Devices |
주요 차별점
- Low verified input noise (vs OP07)
- Precision offset and drift (vs OP27)
- Unity-gain-stable precision positioning (vs OPA37GU)
설계 노트
Keep the OPA27GU input, feedback, and gain-setting paths short and route them away from switching-regulator outputs, relay contacts, and high-current return paths. Place the amplifier close to the protected signal source and use a continuous low-impedance ground reference beneath the analog section. The verified 4.5 nV/√Hz maximum input noise is valuable only when PCB leakage, ground currents, and resistor noise do not dominate the measurement.
Place the supply-bypass capacitors as close as practical to the OPA27GU supply pins, with a short ground return and an adequate analog supply route. Confirm the exact supply-voltage and common-mode limits in the current TI datasheet before selecting bypass values. The supplied data does not include those electrical limits, so capacitor selection must be based on the manufacturer’s recommended application circuit and the actual signal bandwidth.
Do not treat OPA27, OPA37, OP07, and OP27 as automatically interchangeable. Verify the exact suffix, pin names, compensation method, input range, output swing, offset, noise, bias current, and stability for every proposed replacement. A footprint match alone does not guarantee signal-chain compatibility, especially in precision gain stages where a small offset, drift, or bias-current difference can dominate the measurement error.
규정 준수 정보
The verified search data does not provide compliance declarations for the exact OPA27GU ordering code. Confirm current RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification status with Texas Instruments or the authorized distributor.