P2020NSE2HFC - QorIQ P2 Dual-Core 1.2GHz SoC | NXP Semiconductors
부품 번호: P2020NSE2HFC ✓ 활성P2020NSE2HFC 개요
A QorIQ communications processor is a system-on-chip (SoC) built on the Power Architecture instruction set, targeted at wired/wireless infrastructure and embedded networking where deterministic processing, packet acceleration, and security offload matter more than raw clock speed. The QorIQ P2 family sits between the entry-level P1 single-core parts and the higher-tier P3/P4 multicore processors, optimized for mid-range routers, switches, industrial gateways, and secure access equipment.
Key features of the P2020NSE2HFC include dual e500v2 cores at 1.2 GHz, integrated SEC 3.3 engine for IPsec, SSL, and 3GPP cipher acceleration, dual GbE MACs plus two RGMII interfaces, two PCI Express gen 1.1 controllers, two Serial RapidIO ports, USB 2.0 host/device, four UART, two I2C, SPI, and SDHC interfaces, plus NAND flash controller and GPIO. The -125 °C suffix designates the extended-temperature screening tier.
The P2020 employs a coherent dual-core fabric with on-chip 32 KB I-cache and 32 KB D-cache per core, plus a shared 512 KB L2 cache with ECC. The integrated SEC 3.3 engine offloads AES, 3DES, SHA-1/2, MD5, RSA, and elliptic-curve operations, freeing CPU cycles for application-level packet processing. Built on a 45 nm CMOS process, the device typically dissipates 5–12 W depending on core frequency and peripheral activation, requiring thermal management at the PCB level via the exposed die pad.
Typical applications include enterprise routers and VPN gateways, industrial automation controllers, secure network appliances (firewall/UTM), LTE/4G small-cell baseband, networked storage (NAS/iSCSI), smart grid communications, military/aerospace secure routers, and printer/scanner imaging controllers where deterministic performance, ECC memory integrity, and hardware crypto acceleration are mandatory requirements.
When designing with the P2020NSE2HFC, provision a 4-layer or higher PCB with continuous ground planes beneath the BGA, multiple thermal vias in the exposed-pad land pattern, and a 0.1 µF + 10 µF decoupling network at each core voltage pin. The 689-ball TE-PBGA II demands X-ray or endoscopic inspection of solder joints; reflow profile must match JEDEC J-STD-020 MSL3 conditions.
This page synthesizes NXP QorIQ P2 family positioning, drop-in same-package part numbers (P2020NSE2KFC, P2020NSN2MFC and frequency/temperature siblings), DDR2/DDR3 ECC design notes, and BGA PCB layout considerations not consolidated in the manufacturer datasheet alone.
드롭인 대체품: P2020NSE2HFC — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: P2020NSE2HFC (동일 폼 팩터 및 풋프린트) — 차이점: USB, Operating Temperature, Package, RoHS Status, Mounting Type.
P2020NSE2KFC
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
P2020NSN2MFC
✅ 드롭인가격 문의
데이터시트 보기 →P2020NSE2MFC
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
P2010NSE2HFC
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →P2020NSE2HFB
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
P2020NSE2HFC 최대 정격 & 전기적 특성
| Family | QorIQ P2 |
| Core Architecture | PowerPC e500v2 |
| Number of Cores | 2 |
| 데이터 버스 폭 | 32-bit |
| Maximum Core Frequency | 1.2 GHz |
| 동작 온도 범위 | 0 °C to +125 °C |
| Memory Controller | DDR2/DDR3 with ECC |
| Co-Processor / Security Engine | SEC 3.3 (IPsec/SSL/3GPP) |
| Ethernet Interfaces | 10/100/1000 Mbps (RGMII), dual GbE |
| PCI Express | PCIe Gen 1.1 x1/x2/x4 controllers |
| Serial RapidIO | 2x SRIO ports |
| USB | USB 2.0 Host/Device |
| UART | 4x UART |
| I2C / SPI / SDHC | Yes (2x I2C, SPI, SDHC) |
| NAND Flash Controller | Yes |
| L1 Cache (per core) | 32 KB I-cache + 32 KB D-cache |
| L2 Cache (shared) | 512 KB |
| 패키지 | 689-TEPBGA II 31x31 mm with exposed pad |
| RoHS 상태 | Compliant |
P2020NSE2HFC 689-tepbga ii 31x31 mm with exposed pad 핀 구성 가이드
P2020NSE2HFC(689-tepbga ii 31x31 mm with exposed pad 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: P2020NSE2HFC.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
P2020NSE2HFC 적합 용도: 6 애플리케이션s: Enterprise Router / VPN Gateway, Industrial Automation Controller, Secure Network Appliance (Firewall / UTM), LTE / 4G Small-Cell Baseband, Networked Storage (NAS / iSCSI), Smart Grid Communications / Substation Router.
Enterprise Router / VPN Gateway
The P2020NSE2HFC's dual 1.2 GHz e500v2 cores plus the integrated SEC 3.3 engine make it a strong fit for mid-range enterprise routers and IPsec/SSL VPN gateways. The crypto offload sustains multi-gigabit IPsec throughput while the CPU cores handle routing-table lookup, NAT, and QoS queueing — a workload that would saturate a single-core P2010. Place the part on a 4-layer board with continuous GND planes beneath the 689-ball TE-PBGA II and tie the exposed die pad to a thermal via array sized to dissipate the 10-12 W typical draw under full dual-core / GbE / SEC load.
추천
Industrial Automation Controller
In industrial automation, the P2020NSE2HFC delivers deterministic dual-core PowerPC processing with ECC-protected DDR2/3 memory, dual GbE (RGMII) for ring-topology fieldbus backbones, and the -125 °C temperature rating required for outdoor cabinets and factory floors. The integrated 4 UART + 2 I2C + SPI interfaces attach directly to industrial sensors and motor drives without external glue logic. Use ECC-enabled registered DIMMs to guard against soft errors in radiation-prone industrial environments, and add 0.1 µF + 10 µF decoupling networks at every core/IO voltage pin.
추천
Secure Network Appliance (Firewall / UTM)
Unified Threat Management appliances require deep-packet inspection, anti-virus scanning, and IPsec/SSL decryption without line-rate loss. The P2020NSE2HFC's SEC 3.3 engine accelerates AES-NI, RSA, and ECC operations while its dual e500v2 cores handle concurrent control-plane and data-plane threads. The four RGMII-capable SerDes lanes enable multi-GbE uplink configurations (using external PHY MUXes), and the two PCIe Gen 1.1 controllers attach crypto or SSL-accelerator cards for compliance-bound deployments. Expect roughly 4-6 Gbps of IPsec throughput with SEC offload enabled.
추천
LTE / 4G Small-Cell Baseband
Small-cell baseband processing benefits from the P2020NSE2HFC's dual-core architecture, where one core runs the L1 PHY and the second handles L2/L3 protocol stacks over the SRIO interconnect to companion RFICs. The SEC 3.3 engine offloads Kasumi/Snow-3G for LTE ciphering, and the DDR2/DDR3-1066 controller with ECC sustains multi-carrier baseband sample buffering. The 0 to 125 °C range supports outdoor micro/pico-cell deployments, though designers should validate thermal management given the 10-12 W typical draw under simultaneous LTE-A processing.
추천
Networked Storage (NAS / iSCSI)
The P2020NSE2HFC drives entry-to-mid-range NAS and iSCSI SAN appliances, where its dual-core architecture splits iSCSI protocol processing from the RAID/filesystem stack without sacrificing throughput. Dual GbE ports enable link-aggregation or MPIO failover to a second network, while the DDR2/3 controller with ECC protects against silent data corruption in terabyte-scale storage pools. Designers should pair the part with a SATA/SAS controller over PCIe Gen 1.1 and provision 4 GB or more of registered ECC memory for ZFS/cache workloads.
추천
Smart Grid Communications / Substation Router
Smart-grid substation routers must sustain -25 to +85 °C ambient operation, IEC 61850-3 EMI levels, and zero-downtime IPsec tunnels to control centers. The P2020NSE2HFC's 0 to 125 °C operating range, hardware SEC 3.3 for IPsec/GRE/MACsec, dual GbE with hardware timestamping (via the e500v2 TMR), and the rugged BGA-II footprint with proper underfill all meet IEC 61850-3 hardware expectations. ECC memory is mandatory per IEEE 1613 substation hardening; add 1 µF + 10 µF + 100 µF bulk decoupling near the BGA exposed pad for conducted-noise immunity.
추천
추천 제품 요약
엔지니어링 참조 데이터: P2020NSE2HFC — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | P2020NSE2KFC | P2020NSN2MFC | P2020NSE2MFC | P2010NSE2HFC | P2020NSE2HFB |
|---|---|---|---|---|---|---|
| Package | 689-TEPBGA II 31x31 mm | 689-TEPBGA II 31x31 mm — identical | 689-TEPBGA II 31x31 mm — identical | 689-TEPBGA II 31x31 mm — identical | 689-TEPBGA II 31x31 mm — identical | 689-TEPBGA II 31x31 mm — identical |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core Architecture | PowerPC e500v2 (dual-core) | PowerPC e500v2 (dual-core) — same | PowerPC e500v2 (dual-core) — same | PowerPC e500v2 (dual-core) — same | PowerPC e500v2 (single-core) | PowerPC e500v2 (dual-core) |
| Maximum Core Frequency | 1.2 GHz | 1.2 GHz | 1.0 GHz | 1.0 GHz | 1.2 GHz | 1.2 GHz |
| Security Engine | SEC 3.3 | SEC 3.3 | SEC 3.x (different stepping) | SEC 3.3 | SEC 3.3 | SEC 3.3 |
| Number of Cores | 2 | 2 | 2 | 2 | 1 (-50%) | 2 |
주요 차별점
- Dual 1.2 GHz e500v2 cores with symmetric hardware threading (vs P2010NSE2HFC)
- Hardware SEC 3.3 with Kasumi/Snow-3G acceleration (vs P2020NSN2MFC)
- Extended-temperature HFC suffix screening (vs P2020NSE2KFC)
설계 노트
Estimated: the P2020NSE2HFC's 689-ball TE-PBGA II at 1.0 mm pitch requires a 4-layer PCB minimum with 0.5/0.5 oz copper, microvia-in-pad for breakout, and 0.8 mm drill-to-copper spacing on the outermost BGA row. Place 0.1 µF X7R 0402 capacitors on every power pin (eight GVDD groups per the QorIQ hardware spec) plus two 10 µF X5R 0805 bulk caps per rail within 50 mm of the BGA. The exposed die pad must be soldered down to a 6 x 6 or 8 x 8 thermal via array (0.3 mm vias, 1.0 mm pitch) tied to internal GND planes — without this, TJ may exceed the 125 °C limit at full load.
Estimated: at the typical 10-12 W dissipation under dual-core + GbE + SEC workloads, the exposed-pad BGA-II provides a θJA of roughly 15 °C/W with proper via-array heatsinking, giving a TJ rise of about 180 °C above a 25 °C ambient — meaning at 125 °C ambient the junction approaches or exceeds the operating limit. Add a top-side 1 mm copper spreader and (in production) a finned heatsink rated 8 °C/W or lower. Confirm by measured Tc on a thermal-coupon board before qualification.
Do not route DDR2/DDR3 signals across BGA gaps longer than 25 mm; the controller supports trace-matched routing to 50 Ω ±10 percent with 30 ps skew tolerance per byte lane. Skip 90-degree bends in DDR traces, which cause impedance discontinuities at the 1 Gbps data rate. For PCIe, place AC coupling capacitors within 25 mm of the device-side balls, even if the design appears to work without them in simulation — the PCIe Gen 1.1 transmitter compliance test will fail otherwise.
규정 준수 정보
RoHS compliant per NXP product page; lead-free in line with EU 2011/65/EU. REACH compliance status confirmed per NXP material declaration. AEC-Q100 not applicable — QorIQ P2 is not an automotive-qualified part line; use QorIQ automotive variants if required. Halogen-free status to verify against latest NXP material disclosure.
