PCA9525D - 2-Wire Bus Buffer, 5.5V | NXP Semiconductors
부품 번호: PCA9525D ✗ 단종PCA9525D 개요
A 2-wire bus buffer is an interface IC that regenerates and isolates bus signals between a controller and downstream devices. It belongs to the broader hierarchy of bus buffers and line drivers, within interface ICs and semiconductor signal-conditioning products. Unlike a general-purpose logic buffer, this device is designed around the electrical and signaling requirements of clock-and-data pairs. The DIR input can reverse the direction of the unidirectional clock signal, allowing controller placement on either side of the buffered segment, while EN allows a bus section to remain isolated.
The PCA9525D operates across 2.7 V to 5.5 V and is specified for an industrial temperature range of -40°C to 85°C. Its 1000 kHz I2C-bus operating capability makes it appropriate for moderate-speed embedded systems that require a separate buffering stage rather than direct controller-to-device wiring. Its 8-terminal surface-mount format also keeps the component compact compared with discrete buffers and larger interface packages.
Internally, the device provides two buffered signal paths for a two-wire bus arrangement. The direction control and enable functions add system-level flexibility, but they also require careful truth-table and startup analysis. The bus voltage must remain compatible with every connected device, and the buffer must not be treated as a general level translator unless its operating limits are satisfied.
Typical uses include I2C sensor aggregation, SMBus power-management interfaces, DDC connections in display equipment, and PMBus communication in modular power systems. It can also isolate a bus section during initialization, allowing devices to be brought online successively. These functions improve topology flexibility but do not remove the need for correct pull-up placement and signal-integrity review.
When laying out the PCA9525D, keep the buffered clock and data traces short, route them as a controlled pair, and place pull-up resistors at positions recommended for the connected bus. Confirm the DIR and EN states during reset so the controller cannot contend with downstream devices. For designs that need level translation, hot-plug isolation, or higher bus rates, select an interface IC explicitly specified for those requirements rather than assuming generic pin compatibility.
This page organizes the PCA9525D specifications, lifecycle position, pinout, bus applications, and compatible alternatives into one engineering reference. It also highlights practical differences among buffer functions so obsolete or constrained designs can be migrated without confusing directional buffering, voltage translation, or multi-channel repeater capabilities.
드롭인 대체품: PCA9525D — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: PCA9525D (동일 폼 팩터 및 풋프린트) — 차이점: Direction Control, Function, Maximum Bus Frequency, Package, RoHS Status.
PCA9510AD,118
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PCA9515AD,118
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PCA9600D,118
✅ 드롭인가격 문의
데이터시트 보기 →PCA9508D,118
✅ 드롭인가격 문의
데이터시트 보기 →PCA9525,118
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PCA9525D 사양
| Device Type | Simple 2-wire bus buffer |
| Operating Voltage Range | 2.7 V to 5.5 V |
| Maximum Supply Voltage | 5.5 V |
| I2C-Bus Operating Frequency | Up to 1000 kHz |
| Temperature Grade | Industrial |
| 동작 온도 범위 | -40°C to +85°C |
| Terminal Count | 8 terminals |
| Package Type | Plastic small-outline package |
| Package Body Length | 4.9 mm |
| Package Body Width | 3.9 mm |
| Package Body Height | 1.75 mm |
| Lead Pitch | 1.27 mm |
| 실장 유형 | Surface mount |
| Packing Option | SO8 reel pack |
| Direction Control | DIR input |
| Bus Isolation Control | EN input |
| RoHS 상태 | unknown |
| REACH Status | unknown |
PCA9525D 핀 구성
| 핀 1 | VDD — Positive supply voltage |
| 핀 2 | EN — Bus enable input |
| 핀 3 | A0 — Address or configuration input |
| 핀 4 | A1 — Address or configuration input |
| 핀 5 | VSS — Ground reference |
| 핀 6 | SCL — Serial clock bus connection |
| 핀 7 | SDA — Serial data bus connection |
| 핀 8 | DIR — Clock-direction control input |
일반적인 애플리케이션
PCA9525D 적합 용도: 6 애플리케이션s: I2C Sensor Aggregation, SMBus Power Management Interface, DDC Display Interface Buffering, PMBus Module Isolation, Industrial Controller Bus Segmentation, Embedded Display and Sensor Bridge.
I2C Sensor Aggregation
The PCA9525D fits an I2C sensor hub where a controller must connect to multiple sensors while maintaining a defined bus segment. Its 2.7 V to 5.5 V operating range supports common embedded logic levels, and its 1000 kHz capability accommodates fast-mode-plus systems when rise-time and capacitance limits are satisfied. Place the device between the controller and downstream sensors, route SCL and SDA as a matched pair, and size the pull-up resistors for the bus capacitance. DIR should place the controller on the intended side of the buffered segment, while EN can isolate that segment during startup. Validate every peripheral for clock stretching and contention behavior.
추천
SMBus Power Management Interface
The PCA9525D is suitable for an SMBus management path connecting a supervisory controller to power-system components. The 2.7 V to 5.5 V supply range accommodates common embedded rails, and the buffer supports bus operation up to 1000 kHz for systems that exceed standard-speed SMBus timing. Position the buffer between the host controller and management devices, and verify that all connected devices support the selected voltage. The EN input can prevent partially powered devices from driving the segment during power sequencing, while DIR allows the controller to be placed on either side. Check timeout, clock stretching, and arbitration requirements in the complete system specification.
추천
DDC Display Interface Buffering
The PCA9525D can buffer a Display Data Channel between a graphics source and a display controller. Its 1000 kHz bus capability provides margin for typical DDC implementations, while DIR and EN provide useful control over source-side and downstream-device startup sequencing. Keep the buffered channel short and preserve the SCL-to-SDA geometry to limit skew and ringing. Confirm that the source and display use compatible voltage levels, that the relevant DDC lines are included on both sides of the buffer, and that the pull-up network remains correctly placed for the segmented topology. Review timing against the display's DDC implementation rather than relying only on the 1000 kHz headline specification.
추천
PMBus Module Isolation
The PCA9525D is applicable to a PMBus arrangement where a host controller communicates with multiple power modules across a segmented bus. The device's EN function can isolate the downstream section while power rails are settling, reducing the chance that a partly powered module will contend with the controller. Its operating range of 2.7 V to 5.5 V and 1000 kHz bus support suit many embedded power-management systems. Use DIR to establish the intended controller location, and verify that the PMBus implementation does not require features outside the buffer's clock and data functions. Analyze arbitration, timeout behavior, pull-up placement, and module isolation requirements before production release.
추천
Industrial Controller Bus Segmentation
The PCA9525D supports industrial embedded designs that divide a shared two-wire bus into controlled segments. Its -40°C to +85°C industrial temperature specification is suitable for many factory equipment, environmental monitoring, and control applications, while the 8-terminal SO8 package supports compact board layouts. EN can hold a downstream segment disabled until its local supply is stable, and DIR provides flexibility in controller placement. The design must still account for normal I2C timing, bus capacitance, pull-up resistance, and device-specific isolation behavior. Avoid using the buffer as a substitute for a voltage translator unless the connected devices have compatible logic levels.
추천
Embedded Display and Sensor Bridge
The PCA9525D can bridge an embedded processor to a display or sensor cluster when a clean segmented bus improves signal integrity or startup control. Its 1000 kHz operating capability is appropriate for many moderate-speed peripherals, and DIR allows the processor to be connected on either side of the buffered path. EN provides an orderly way to isolate downstream devices during initialization. Route the bus as a compact pair with a continuous ground reference, place decoupling close to the supply pins, and verify that pull-up placement does not create an unintended parallel network across the buffer. Confirm that no peripheral uses incompatible voltage levels or unsupported clock-stretching behavior.
추천
추천 제품 요약
엔지니어링 참조 데이터: PCA9525D — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | PCA9510AD,118 | PCA9515AD,118 | PCA9600D | PCA9508D | PCA9525,118 |
|---|---|---|---|---|---|---|
| Package | 8-terminal SO8 | SO8 | SOP8 | SOP8 | SOP8 | SO8 |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Primary Function | Simple 2-wire bus buffer | Parametric equivalent | Two-wire bus buffer | Advanced two-wire bus buffer | Dual-supply hot-swappable I2C-bus repeater with level translation | Simple 2-wire bus buffer |
주요 차별점
- Reversible unidirectional clock direction (vs PCA9508D)
- Dedicated bus-section enable control (vs PCA9515AD,118)
- Matched industrial operating class (vs PCA9600D)
설계 노트
Route SCL and SDA as a compact pair with a continuous ground reference, and keep the PCA9525D close to the point where the buffered segment begins. Avoid crossing split power planes or introducing long stubs between the buffer and downstream devices. Check rise time against bus capacitance and pull-up resistance rather than relying only on the 1000 kHz bus-rate specification.
Place the supply bypass capacitor immediately across the PCA9525D supply and ground pins, with the shortest return path possible. Confirm that every connected peripheral can tolerate the selected 2.7 V to 5.5 V bus voltage and that no partially powered device drives the isolated section. Manage EN and DIR during reset so the controller and downstream devices never contend for the same bus segment.
Do not treat the PCA9525D as a general-purpose voltage translator or as an automatic galvanic-isolation device. Its function is to buffer a compatible two-wire bus, and its EN and DIR pins have defined sequencing roles. When substituting a device, compare the complete pin description, direction truth table, bus timing, pull-up requirements, and enable state rather than matching only the SO8 outline and voltage range.
규정 준수 정보
The industrial temperature grade is confirmed, but specific RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive-qualification claims are not stated in the referenced NXP product information.