PIC12F609-E/MS - 1.75KB Flash 8-Bit MCU | Microchip 8-MSOP
부품 번호: PIC12F609-E/MS ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $0.92 | $0.92 |
| 10 | $0.83 | $8.30 |
| 100 | $0.74 | $74.00 |
| 500 | $0.66 | $330.00 |
| 1,000 | $0.59 | $590.00 |
PIC12F609-E/MS 개요
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, working RAM, and peripheral interfaces on one IC. The PIC12F609 belongs to the PIC12F family of mid-range 8-bit microcontrollers (PIC -> microcontroller -> embedded processor -> semiconductor), built on CMOS technology with a RISC instruction set optimized for deterministic execution and low power consumption. This architecture positions it between simple 8-pin PIC10 devices and larger PIC16/PIC18 parts.
Key features of the PIC12F609-E/MS include 1.75 KB self-programmable Flash, an 8-channel 10-bit ADC, one 8-bit and one 16-bit timer, an enhanced PWM module, an analog comparator, and an internal 8 MHz oscillator with calibration. The part also offers a power-on reset, brown-out reset, watchdog timer with its own on-chip RC oscillator, and in-circuit serial programming (ICSP) for field upgrades.
Typical applications include LED lighting control, battery chargers, sensor signal conditioning, low-power remote controls, and automotive body modules. The wide 2.0-5.5 V supply range and small MSOP-8 footprint suit it to coin-cell powered, hand-held, and sealed-environment designs.
When designing with this part, ensure the ICSPDAT/ICSPCLK pins are not held low at power-up to enter programming mode, and keep ADC input source impedance below 10 kohm to preserve 10-bit accuracy. An external decoupling capacitor of 100 nF placed within 5 mm of VDD is recommended for noise immunity.
This page synthesizes real-time distributor pricing, drop-in alternatives in the same MSOP-8 footprint, and engineering design notes not aggregated in the Microchip datasheet alone.
드롭인 대체품: PIC12F609-E/MS — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: PIC12F609-E/MS (동일 폼 팩터 및 풋프린트) — 차이점: Package, Core Architecture, Internal Oscillator, Operating Temperature, Comparators.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
PIC12F609-I/MS
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC12F609T-I/MS
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC12F609-E/MD
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$0.66 / 개
데이터시트 보기 →PIC12F615-I/MS
✅ 드롭인✓ 재고 있음
$0.62 / 개
데이터시트 보기 →PIC12F617-I/MS
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC12F509-E/MS
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$0.82 / 개
데이터시트 보기 →PIC12F609-E/MS 최대 정격 & 전기적 특성
| Core Architecture | 8-bit PIC RISC (mid-range) |
| Program Memory (Flash) | 1.75 KB (1K x 14 words) |
| RAM | 64 bytes |
| EEPROM | 0 bytes (Flash-based emulation) |
| Max CPU Frequency | 20 MHz |
| Supply Voltage (VDD) | 2.0 V to 5.5 V |
| I/O Pins | 6 (5 GPIO + 1 input-only) |
| Internal Oscillator | 8 MHz (factory calibrated) |
| ADC | 8-channel, 10-bit |
| Timers | 1 x 8-bit, 1 x 16-bit |
| PWM | Enhanced CCP, 10-bit resolution |
| Comparators | 1 analog comparator |
| Temperature Grade | -40 C to +125 C (Extended, -E) |
| 패키지 | 8-pin MSOP |
| ICSP | Yes (In-Circuit Serial Programming) |
| Watchdog Timer | Yes, with dedicated WDT oscillator |
| Brown-out Reset | Yes |
| RoHS 상태 | Compliant |
PIC12F609-E/MS 핀 구성
| 핀 1 | VDD — Positive supply voltage (2.0 V to 5.5 V) |
| 핀 2 | GP5/T1CKI/OSC1/CLKIN — GPIO / Timer1 clock / crystal oscillator / external clock input |
| 핀 3 | GP4/AN3/T1G/OSC2/CLKOUT — GPIO / ADC ch3 / Timer1 gate / crystal out / clock out |
| 핀 4 | GP3/MCLR/VPP — GPIO / Master Clear (reset) / ICSP programming voltage |
| 핀 5 | GP2/AN2/T0CKI/INT/COUT/CCP1 — GPIO / ADC ch2 / Timer0 clk / external int / comparator out / CCP1 PWM |
| 핀 6 | GP1/AN1/CIN-/ICSPCLK — GPIO / ADC ch1 / comparator in- / ICSP clock |
| 핀 7 | GP0/AN0/CIN+/ICSPDAT — GPIO / ADC ch0 / comparator in+ / ICSP data |
| 핀 8 | VSS — Ground reference |
일반적인 애플리케이션
PIC12F609-E/MS 적합 용도: 6 애플리케이션s: Battery-Powered Sensor Node, LED Lighting Controller, Automotive Body Electronics, Remote Control / IR Transmitter, Industrial Control / Sensor Conditioning, Home Appliance User Interface.
Battery-Powered Sensor Node
The PIC12F609-E/MS is well suited for low-duty-cycle battery-powered sensor nodes where its 2.0-5.5 V supply range supports direct connection to a single Li-Ion or two AA cells. Its 64 B RAM, 6 GPIO, and 8-channel ADC are sufficient to read temperature, voltage, and one analog sensor while driving a sleep-mode quiescent current. Compared with a discrete uC + op-amp solution, the integrated 10-bit ADC and analog comparator eliminate external analog signal-conditioning components, reducing BOM cost and PCB area. The 20 MHz instruction rate allows 8 MHz ADC sampling at full 10-bit resolution while leaving CPU bandwidth for periodic wake-up math.
추천
LED Lighting Controller
In LED driver and lighting-control modules, the PIC12F609-E/MS provides PWM dimming, current sensing via the analog comparator, and button input handling in a single MSOP-8 package. The enhanced CCP module generates 10-bit PWM at up to 20 kHz, eliminating LED flicker while supporting smooth dimming curves stored in the 1.75 KB Flash. Its 2.0 V minimum VDD allows direct drive from a single-cell Li-Ion or two-cell alkaline stack, simplifying the power tree. Pin compatibility with PIC12F617-I/MS enables seamless migration to designs requiring 4-channel PWM for RGB or tunable-white lighting.
추천
Automotive Body Electronics
The -E extended temperature grade (-40 C to +125 C) qualifies the PIC12F609-E/MS for under-hood and cabin automotive body modules such as seat controllers, mirror adjusters, and accessory delay timers. Its 6 GPIO can drive relays and read switches directly, while the internal 8 MHz oscillator removes external crystal cost in vibration-prone mounting locations. Automotive designers value its robust brown-out reset and watchdog timer with dedicated WDT RC oscillator, which guard against supply transients and software lockups. The MSOP-8 footprint simplifies PCB layout behind dashboard clusters where space is severely constrained.
추천
Remote Control / IR Transmitter
For handheld IR/RF remote controls, the PIC12F609-E/MS offers low sleep current, 8 MHz internal oscillator (no external crystal), and 6 GPIO for matrix keypad or capacitive-touch buttons. Its 1.75 KB Flash is enough for RC5/RC6/SIRC IR protocols plus button debouncing and battery-level ADC sampling, while the 20 MHz CPU rate generates 38 kHz / 40 kHz carrier PWM directly without external timing chips. The MSOP-8 package fits inside a slim AAA-battery enclosure with battery contacts on either end. Designers value the ICSP interface for factory firmware updates and the brown-out reset for clean wake-up from battery replacement.
추천
Industrial Control / Sensor Conditioning
In 4-20 mA loop-powered industrial sensor transmitters, the PIC12F609-E/MS digitizes a 0-5 V analog input via its 10-bit ADC and drives a PWM-output DAC or HART modem. The wide 2.0-5.5 V supply range accommodates loop-powered designs with shunt regulators, while the -E temperature grade supports outdoor installations. Its watchdog timer and brown-out reset provide field-grade reliability against EMI-induced resets and supply brownouts. The MSOP-8 footprint simplifies integration inside small IP65 sensor heads where PCB area is only a few square centimeters.
추천
Home Appliance User Interface
White-goods and small home appliances such as coffee makers, irons, and toaster ovens use the PIC12F609-E/MS for tactile-button input, LED status indication, and triac-fired heater control. The internal 8 MHz oscillator and ICSP eliminate external resonator cost, while the analog comparator implements zero-cross detection for triac phase-angle dimming. With 1.75 KB Flash the part holds a small user-interface state machine plus triac-firing logic without external EEPROM. The -E temperature rating supports kitchen-ambient conditions above 85 C near oven-mounted control boards.
추천
추천 제품 요약
엔지니어링 참조 데이터: PIC12F609-E/MS — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | PIC12F609-I/MS | PIC12F615-I/MS | PIC12F617-I/MS | PIC12F509-E/MS |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | MSOP-8 | MSOP-8 - same | MSOP-8 - same | MSOP-8 - same | MSOP-8 - same |
| Flash Memory | 1.75 KB | 1.75 KB - same | 2 KB (+14%) | 2 KB (+14%) | 1.5 KB (-14%) |
| RAM | 64 B | 64 B - same | 64 B - same | 128 B (+100%) | 41 B (-36%) |
| ADC | 8-ch, 10-bit | 8-ch, 10-bit | 8-ch, 10-bit - same | 4-ch, 10-bit | None |
| Max CPU Speed | 20 MHz | 20 MHz - same | 20 MHz - same | 20 MHz - same | 20 MHz - same |
| Temperature Grade | -40 to +125 C (Extended) | -40 to +85 C (Industrial) | -40 to +85 C (Industrial) | -40 to +85 C (Industrial) | -40 to +125 C (Extended) - same |
| PWM Channels | 1 (Enhanced CCP) | 1 (Enhanced CCP) - same | 1 (Enhanced CCP) - same | 3 (Enhanced PWM) | 0 |
| Internal Oscillator | 8 MHz | 8 MHz - same | 8 MHz - same | 8 MHz - same | 4 MHz - slower |
주요 차별점
- Extended -40 to +125 C temperature grade with Flash memory (vs PIC12F509-E/MS)
- Integrated 10-bit ADC for sensor conditioning (vs PIC12F617-I/MS)
- Industry-standard 8-pin MSOP footprint for cross-vendor compatibility (vs PIC12F609-E/SN)
설계 노트
Decouple VDD (pin 1) with a 100 nF X7R ceramic capacitor placed within 5 mm of the IC and tie VSS (pin 8) directly to a low-impedance ground pour. Add a 10 uF bulk tantalum or ceramic capacitor on the same rail to suppress switching transients from relays or PWM-driven triacs. Microchip datasheet DS-41302D specifies brown-out trip thresholds of 2.0 V nominal (BOR at 2.0V setting) so a 3.3 V LDO with 200 mV dropout margin is recommended for battery-powered designs.
Route the ICSPDAT (GP0, pin 7) and ICSPCLK (GP1, pin 6) traces to a 6-pin header with no series resistors and no sharing of long traces with high-current switching nodes. Keep GP3/MCLR (pin 4) pulled to VDD through a 10 kohm resistor with a 100 nF decoupling cap to ground; do NOT tie this pin directly to VDD as that disables in-circuit programming. Use a star-ground topology if the design mixes analog (ADC reference) and digital (ICSP / PWM) return currents.
The 10-bit ADC achieves specified accuracy when the analog source impedance is below 10 kohm per Microchip datasheet DS-41302D. Add an external buffer op-amp (e.g., MCP6001) if higher-impedance sensors are used. Place the AVR_ADC channel near the IC to minimize track capacitance, and avoid running ADC traces parallel to high-frequency switching nodes like PWM outputs.
A common pitfall is configuring GP3 as a digital input while leaving MCLR disabled; this leaves the device unable to reset and can hang the application if a brown-out event occurs. Another is running the CPU at 20 MHz with VDD below 4.5 V, which violates the electrical specification and may cause unstable instruction execution. Finally, do not omit the WDT postscaler setting - Microchip ships the device with WDT enabled by default at the slowest postscaler, which can cause unexpected resets in long-running loops.
규정 준수 정보
RoHS and REACH compliant per Microchip product page. MSOP-8 package is lead-free with matte-tin plating. No AEC-Q100 variant in the -E temperature grade; automotive designers should consult PIC16F or PIC18F Q1 families if functional-safety qualification is required.
