PIC16C64AT-20E/PT - 8-bit OTP MCU, 20MHz, 44-TQFP | Microchip
부품 번호: PIC16C64AT-20E/PT ✗ 단종| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $6.45 | $6.45 |
| 10 | $5.85 | $58.50 |
| 100 | $5.2 | $520.00 |
| 500 | $4.62 | $2,310.00 |
| 1,000 | $4.1 | $4,100.00 |
PIC16C64AT-20E/PT 개요
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, working RAM, and peripheral interfaces on one die, enabling compact, low-power embedded designs. PIC16C-series OTP MCUs belong to the broader 8-bit microcontroller category, sitting hierarchically above general-purpose microcontrollers, microcontrollers, and semiconductor integrated circuits. They are characterized by a RISC-based Harvard architecture with separate program and data buses, deterministic interrupt latency, and OTP ROM for code storage in cost-sensitive or short-run production.
Key features of the PIC16C64AT-20E/PT include a wide operating voltage range of 2.5 V to 6.0 V, brown-out detect and reset (BOD/BOR) for safe power-up behavior, a power-on reset (POR) circuit, a watchdog timer (WDT) for runaway code recovery, and pulse-width modulation (PWM) outputs suitable for motor or lighting control. The integrated 10-bit ADC provides analog signal acquisition with up to 8 input channels, while the synchronous serial port supports both SPI and I2C master/slave protocols for sensor and peripheral expansion.
Architecturally, the PIC16C64A employs a 14-bit instruction word with a single accumulator-based working register (WREG) and a small file-register map, delivering deterministic execution at 4 clock cycles per instruction (200 ns per instruction at 20 MHz). The CMOS process technology yields low power consumption suitable for battery-backed industrial control, automotive body electronics, and appliance subsystems, with sleep current low enough for long-term standby operation.
Typical applications include industrial control panels, HVAC sensor interfaces, motor control boards, automotive body modules, appliance user interfaces, and general-purpose embedded controllers in the PIC16C legacy ecosystem. The 44-TQFP package supports compact, high-density PCB layouts and is compatible with standard SMT assembly lines.
When designing with the PIC16C64AT-20E/PT, ensure that MCLR is properly pulled high through a resistor-capacitor network, and place decoupling capacitors (100 nF and 10 uF) close to the VDD/VSS pairs. Note that the OTP variant cannot be reprogrammed, so choose the flash-based PIC16F877A or PIC16F887 if in-system firmware updates are required.
드롭인 대체품: PIC16C64AT-20E/PT — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: PIC16C64AT-20E/PT (동일 폼 팩터 및 풋프린트) — 차이점: Operating Temperature Range, RoHS Status, RAM Size, Core Architecture, Package.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
PIC16C64A-20I/PT
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC16C64A-20E/PT
✅ 드롭인✓ 재고 있음
$12.4 / 개
데이터시트 보기 →PIC16C64AT-10E/PT
✅ 드롭인✓ 재고 있음
$4.1 / 개
데이터시트 보기 →PIC16C64A-10I/PT
✅ 드롭인✓ 재고 있음
$5.85 / 개
데이터시트 보기 →PIC16C64A-10E/PT
✅ 드롭인✓ 재고 있음
$8.95 / 개
데이터시트 보기 →PIC16C64A-04E/PT
✅ 드롭인✓ 재고 있음
$7.35 / 개
데이터시트 보기 →PIC16C64AT-20E/PT 최대 정격 & 전기적 특성
| Core Architecture | 8-bit PIC16C RISC |
| Program Memory Type | OTP ROM |
| Program Memory Size | 3.5 KB (2K x 14) |
| RAM Size | 128 bytes |
| Maximum CPU Frequency | 20 MHz |
| Operating Voltage Range | 2.5 V to 6.0 V |
| I/O Pin Count | 33 |
| ADC | 10-bit, multi-channel |
| Timers | 2x 8-bit + 1x 16-bit |
| Serial Interfaces | I2C, SPI (SSP) |
| PWM Channels | Yes (Capture/Compare/PWM) |
| Brown-out Detect/Reset | Yes |
| Power-On Reset (POR) | Yes |
| Watchdog Timer (WDT) | Yes |
| 패키지 | 44-TQFP (10x10 mm) |
| 동작 온도 범위 | -40C to +125C (E suffix, extended) |
| 실장 유형 | Surface Mount |
| RoHS 상태 | Compliant |
PIC16C64AT-20E/PT 핀 구성
| 핀 1 | OSC1/CLKIN — Oscillator crystal input or external clock input |
| 핀 2 | OSC2/CLKOUT — Oscillator crystal output; CLKOUT in RC mode |
| 핀 3 | MCLR/VPP — Master Clear reset input / programming voltage |
| 핀 4 | RA0/AN0 — PORTA bit 0 / Analog input 0 |
| 핀 5 | RA1/AN1 — PORTA bit 1 / Analog input 1 |
| 핀 6 | RA2/AN2 — PORTA bit 2 / Analog input 2 |
| 핀 7 | RA3/AN3/VREF — PORTA bit 3 / Analog input 3 / ADC reference |
| 핀 8 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| 핀 9 | RA5/AN4/SS — PORTA bit 5 / Analog input 4 / SPI slave select |
| 핀 10 | VSS — Ground reference |
| 핀 11 | VDD — Positive supply voltage |
| 핀 12 | RB0/INT — PORTB bit 0 / External interrupt |
| 핀 13 | RB1 — PORTB bit 1 |
| 핀 14 | RB2 — PORTB bit 2 |
| 핀 15 | RB3 — PORTB bit 3 |
| 핀 16 | RB4 — PORTB bit 4 |
| 핀 17 | RB5 — PORTB bit 5 |
| 핀 18 | RB6/PGC — PORTB bit 6 / ICSP clock |
| 핀 19 | RB7/PGD — PORTB bit 7 / ICSP data |
| 핀 20 | VSS — Ground reference |
| 핀 21 | VDD — Positive supply voltage |
| 핀 22 | RC0/T1OSO/T1CKI — PORTC bit 0 / Timer1 oscillator output / clock in |
| 핀 23 | RC1/T1OSI/CCP2 — PORTC bit 1 / Timer1 oscillator in / CCP2 |
| 핀 24 | RC2/CCP1 — PORTC bit 2 / Capture Compare PWM 1 |
| 핀 25 | RC3/SCK/SCL — PORTC bit 3 / SPI clock / I2C clock |
| 핀 26 | RC4/SDI/SDA — PORTC bit 4 / SPI data in / I2C data |
| 핀 27 | RC5/SDO — PORTC bit 5 / SPI data out |
| 핀 28 | RC6/TX/CK — PORTC bit 6 / USART transmit / clock |
| 핀 29 | RC7/RX/DT — PORTC bit 7 / USART receive / data |
| 핀 30 | VSS — Ground reference |
| 핀 31 | VDD — Positive supply voltage |
| 핀 32 | RD0 — PORTD bit 0 |
| 핀 33 | RD1 — PORTD bit 1 |
| 핀 34 | RD2 — PORTD bit 2 |
| 핀 35 | RD3 — PORTD bit 3 |
| 핀 36 | RD4 — PORTD bit 4 |
| 핀 37 | RD5 — PORTD bit 5 |
| 핀 38 | RD6 — PORTD bit 6 |
| 핀 39 | RD7 — PORTD bit 7 |
| 핀 40 | VSS — Ground reference |
| 핀 41 | VDD — Positive supply voltage |
| 핀 42 | RE0/RD — PORTE bit 0 / Parallel slave port read |
| 핀 43 | RE1/WR — PORTE bit 1 / Parallel slave port write |
| 핀 44 | RE2/CS — PORTE bit 2 / Parallel slave port chip select |
일반적인 애플리케이션
PIC16C64AT-20E/PT 적합 용도: 6 애플리케이션s: Industrial Control Panels, Automotive Body Electronics, HVAC Sensor Interfaces, Motor Control Boards, Appliance User Interfaces, Legacy PIC16C System Sustainment.
Industrial Control Panels
The PIC16C64AT-20E/PT's 33 digital I/O pins, 8-channel 10-bit ADC, and integrated I2C/SPI ports make it well suited for industrial control panel HMIs and PLC I/O expansion boards. Its 20 MHz core delivers deterministic 200 ns instruction cycle time, critical for closed-loop PID loops driving relays, contactors, and motor starters. The extended -40C to +125C temperature grade (E suffix) supports factory-floor enclosures with wide thermal swings, while the 44-TQFP footprint eases integration into compact panel-mount PCAs. Compared to flash-based successors, the OTP variant locks firmware against unauthorized modification in long-life industrial installations.
추천
Automotive Body Electronics
The PIC16C64AT-20E/PT is used in automotive body controllers managing lighting clusters, seat controls, climate panel keypads, and simple body ECUs where cost dominates over flash reprogrammability. Its brown-out reset (BOR) and watchdog timer (WDT) safeguard against the load-dump transients and voltage drops typical of 12V automotive buses, while the PWM outputs drive LED dimming and small DC motor speed control. The 44-TQFP package fits within space-constrained behind-dash housings, and the extended -40C to +125C grade handles underhood and cabin thermal extremes. Migrate to PIC16F877A or PIC18F variants only when in-system firmware updates are mandated.
추천
HVAC Sensor Interfaces
The PIC16C64AT-20E/PT's integrated 10-bit ADC with up to 8 input channels and I2C peripheral is ideal for HVAC sensor interface boards that aggregate temperature, humidity, and pressure transducers. Its 20 MHz core provides sufficient bandwidth for averaging, linearization, and digital filtering of sensor data before transmission to a master controller via SPI or I2C. The wide 2.5 V to 6.0 V supply range supports both 3.3 V and 5 V transducer rails commonly found in rooftop and split HVAC units. The 44-TQFP's 10x10 mm body eases hand-repair and rework in the field, an advantage over smaller QFN packages in commercial HVAC service.
추천
Motor Control Boards
The PIC16C64AT-20E/PT's Capture/Compare/PWM (CCP) module and 16-bit TMR1 timer make it a capable controller for small brushed DC and unipolar stepper motor boards used in printers, small appliances, and valve actuators. At 20 MHz, PWM frequency can reach tens of kHz with fine duty-cycle resolution, enabling smooth speed and torque control. The 33 digital I/O pins accept quadrature encoder inputs, end-stop switches, and direction signals, while the ADC reads current-sense shunts for basic stall protection. The 44-TQFP package allows component placement on both sides of the board, beneficial for compact motor driver PCAs.
추천
Appliance User Interfaces
In washing machines, microwave ovens, dishwashers, and similar white goods, the PIC16C64AT-20E/PT functions as the user-interface controller driving seven-segment or character LCD displays, scanning keypads, and controlling indicator LEDs. Its low power consumption in sleep mode extends battery life in clock-backup subsystems, while the BOR and WDT defend against the noisy switch-mode supplies that share the appliance chassis. The 44-TQFP package offers reliable reflow assembly on high-volume SMT lines, and the OTP memory locks the user interface firmware to prevent post-sale tampering. E-segment temperature grade supports appliance thermal environments around heating elements and compressor enclosures.
추천
Legacy PIC16C System Sustainment
Many long-life products in medical instrumentation, defense electronics, and industrial automation designed in the late 1990s and early 2000s use the PIC16C64A family and must be sustained for 15-25 year production runs. The PIC16C64AT-20E/PT in 44-TQFP provides a drop-in replacement for board repairs on these mature designs where re-spinning to flash-based silicon is not economically justified. Microchip's NRND designation is currently in effect, so qualification of an authorized second-source or inventory pipeline is essential. The 44-TQFP footprint remains compatible with the PIC16F877A-I/PT for design refresh when firmware updates become necessary.
추천
추천 제품 요약
엔지니어링 참조 데이터: PIC16C64AT-20E/PT — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | PIC16C64A-20I/PT | PIC16C64A-20E/PT | PIC16C64AT-10E/PT | PIC16C64A-10I/PT | PIC16C64A-04E/PT |
|---|---|---|---|---|---|---|
| Package | 44-TQFP (10x10 mm) | 44-TQFP (10x10) - same | 44-TQFP (10x10) - same | 44-TQFP (10x10) - same | 44-TQFP (10x10) - same | 44-TQFP (10x10) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Maximum Clock Frequency | 20 MHz | 20 MHz | 20 MHz | 10 MHz (-50%) | 10 MHz (-50%) | 4 MHz (-80%) |
| Program Memory Type | OTP ROM (3.5 KB) | OTP ROM (3.5 KB) | OTP ROM (3.5 KB) | OTP ROM (3.5 KB) | OTP ROM (3.5 KB) | OTP ROM (3.5 KB) |
| RAM Size | 128 bytes | 128 bytes | 128 bytes | 128 bytes | 128 bytes | 128 bytes |
| Operating Temperature | -40C to +125C (E) | -40C to +85C (I) | -40C to +125C (E) | -40C to +125C (E) | -40C to +85C (I) | -40C to +125C (E) |
| I/O Pins | 33 | 33 | 33 | 33 | 33 | 33 |
| ADC | 10-bit, 8 channels | 10-bit, 8 channels | 10-bit, 8 channels | 10-bit, 8 channels | 10-bit, 8 channels | 10-bit, 8 channels |
주요 차별점
- Extended -40C to +125C temperature grade in same 44-TQFP package (vs PIC16C64A-20I/PT)
- 20 MHz core clock in legacy PIC16C family (vs PIC16C64AT-10E/PT)
- Original PIC16C64A silicon on 44-TQFP - not PIC16F derivative (vs PIC16F877A-I/PT)
설계 노트
The PIC16C64AT-20E/PT requires a stable VDD between 2.5 V and 6.0 V with brown-out reset (BOR) enabled for reliable operation in noisy industrial environments. Place a 100 nF decoupling capacitor within 5 mm of each VDD pin and a bulk 10 uF tantalum or ceramic capacitor near the MCU's VDD pins. The BOR threshold must be configured below the minimum expected supply rail to avoid spurious resets during normal load transients.
The PIC16C64A uses One-Time-Programmable (OTP) memory that cannot be erased once programmed. Design the development cycle on a UV-erasable PIC16C64A windowed sample or PIC16F877A-I/PT (flash-based, 44-TQFP compatible) before committing to OTP production silicon. Mistakes in production firmware require physical replacement of every OTP device on a board, which can be costly for field-deployed units.
Route the MCLR line separately from switching traces and place a 10 kohm pull-up and 100 nF capacitor to ground at the MCLR pin to suppress ESD-induced resets. The OSC1/OSC2 traces should be as short as possible and surrounded by a ground guard ring to limit radiated EMI, especially in motor-control and switching-supply applications. Avoid running high-current switching traces parallel to the analog ADC inputs (AN0-AN7) to minimize coupled noise into conversion results.
At 20 MHz clock with all peripherals active, the PIC16C64AT-20E/PT typically draws 10-20 mA from VDD, dissipating less than 120 mW even at 6.0 V. The 44-TQFP package's exposed thermal pad (if present in the TQFP variant used) should be soldered to a copper pour to reduce junction-to-ambient thermal resistance. Standard 4-layer FR4 PCB designs keep the die temperature well within the -40C to +125C operating range.
규정 준수 정보
RoHS compliant per Microchip material declaration; lead-free matte-tin terminations; rated to JEDEC J-STD-020 peak reflow 260C. Not AEC-Q100 qualified - refer to AEC-Q100-qualified PIC16 variants for automotive safety-critical applications.