PIC16F1517-E/P 20MHz 8-Bit MCU 14KB Flash | Microchip
부품 번호: PIC16F1517-E/P ✓ 활성PIC16F1517-E/P 개요
A PIC16F microcontroller is an embedded-control semiconductor that combines a processor core, Flash program memory, data RAM, digital I/O and configurable peripherals on one integrated circuit. The PIC16F1517 belongs to the enhanced mid-range PIC16 family, combining a compact instruction set with integrated analog and serial communications functions. Its XLP design is intended for applications where low operating power and efficient standby behavior are important.
The key features of the PIC16F1517-E/P include 8K × 14-word Flash organization, 512 bytes of SRAM, a 10-bit Analog-to-Digital Converter and an operating voltage range of 1.8 V to 5.5 V. The extended-temperature designation corresponds to an operating range of −40 °C to +125 °C. Two CCP peripherals support capture, compare, PWM and timer functions, while SPI, MI2C and EUSART provide wired communication options without requiring separate interface devices.
The device uses Microchip's enhanced mid-range core and is supported by the MPLAB development environment. Programmable peripherals can monitor digital inputs, measure analog voltages and generate PWM waveforms, allowing a single controller to supervise sensors, drive actuators and exchange data with other embedded modules. Configuration fuses and internal oscillator options should be selected with the programming tool and application requirements before PCB release.
Typical applications include industrial control panels, temperature monitoring, motor and actuator controllers, LED lighting systems, low-cost serial data loggers, appliance interfaces and compact battery-powered instruments. The 40-pin PDIP package provides generous I/O access for prototype and industrial control boards where through-hole assembly is acceptable. Its 1.8 V minimum supply voltage also supports low-voltage systems that require the same MCU and peripherals at reduced supply levels.
PCB designers should reserve all 40 package positions even when a particular design leaves some I/O unused, follow the manufacturer's decoupling and analog-input guidance, and verify programming and in-circuit-debug connections before fabrication. Because the -E/P suffix specifies the 40-pin PDIP package and extended temperature grade, it cannot be substituted mechanically with 44-pin TQFP or 28-pin variants without changing the PCB footprint.
드롭인 대체품: PIC16F1517-E/P — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: PIC16F1517-E/P (동일 폼 팩터 및 풋프린트) — 차이점: Package, Mounting Type, Program Memory Size, ADC, ADC Resolution.
PIC16F1517-I/PT
✅ 드롭인가격 문의
데이터시트 보기 →PIC16F1518-E/P
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
PIC16F1518-I/P
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
PIC16F1519-E/P
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →PIC16F1519-I/P
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →PIC16F1517-E/P 최대 정격 & 전기적 특성
| Controller Type | 8-bit PIC16F microcontroller |
| Maximum CPU Frequency | 20 MHz |
| Program Memory Size | 14 KB Flash |
| Program Memory Organization | 8K × 14 words |
| Data Memory Size | 512 bytes RAM |
| ADC Resolution | 10 bits |
| Operating Voltage Range | 1.8 V to 5.5 V |
| 동작 온도 범위 | −40 °C to +125 °C |
| 패키지 | 40-pin PDIP |
| CCP Modules | 2 |
| Serial Interfaces | SPI, MI2C and EUSART |
| 실장 유형 | Through-hole |
| Low-Power Technology | nanoWatt XLP |
| Programming Interface | ICSP |
| Development Environment | MPLAB X IDE |
| Debug Support | MPLAB-compatible in-circuit debugging |
PIC16F1517-E/P 40-pin pdip 핀 구성 가이드
PIC16F1517-E/P(40-pin pdip 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: PIC16F1517-E/P.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
PIC16F1517-E/P 적합 용도: 6 애플리케이션s: Industrial Control and Sensor Interface, Temperature Monitoring and Data Logging, Motor and Actuator Control, LED Lighting and Dimming Control, Serial Communication Gateway, Battery-Powered Measurement Instrument.
Industrial Control and Sensor Interface
The PIC16F1517-E/P suits compact industrial controllers because it combines an 8-bit core, 20 MHz operating speed, 14 KB of Flash and a 10-bit ADC in a 40-pin PDIP package. Its 1.8 V to 5.5 V supply range provides flexibility when the board includes low-voltage sensors, while two CCP modules can measure timing events or generate PWM control signals. SPI, MI2C and EUSART permit connection to external transducers, display controllers and service interfaces. The −40 °C to +125 °C rating supports equipment operating across wide environmental changes.
추천
Temperature Monitoring and Data Logging
The PIC16F1517-E/P can supervise analog sensors through its 10-bit ADC and retain operating logic in 14 KB of Flash while using 512 bytes of RAM for temporary measurements and communication buffers. SPI, MI2C and EUSART enable attachment to external flash storage, digital temperature sensors or a host computer. A 20 MHz core provides sufficient timing headroom for periodic sampling, filtering and packet formatting. The extended-temperature grade is useful for monitoring equipment placed in cabinets, vehicles or industrial enclosures with significant thermal variation.
추천
Motor and Actuator Control
The PIC16F1517-E/P is appropriate for small motor, valve and actuator control systems that need precise timing without a high-cost MCU. Two CCP peripherals can provide PWM output, input capture and compare functions, while the 20 MHz core can coordinate multiple control sequences. The 10-bit ADC can monitor current, position or supply feedback from external conditioning circuits, and EUSART can connect to a remote controller. Because the 40-pin PDIP footprint exposes more I/O than smaller packages, it also allows expansion for drivers, interlocks and diagnostic signals.
추천
LED Lighting and Dimming Control
The PIC16F1517-E/P can implement LED dimming, status indication and programmable lighting sequences using its timer and PWM-capable CCP peripherals. Its 14 KB Flash provides space for calibration tables, operating profiles and communication routines, while 512 bytes of RAM is sufficient for typical dimming state and serial buffers. The 1.8 V to 5.5 V operating range supports low-voltage lighting modules as well as 5 V industrial controllers. Its −40 °C to +125 °C grade is particularly relevant to luminaires and lighting controls installed outside conditioned environments.
추천
Serial Communication Gateway
The PIC16F1517-E/P can bridge local sensors and a higher-level controller because it includes SPI, MI2C and EUSART in the same package as its 8-bit processor. The 20 MHz CPU supports protocol conversion, framing, checksums and basic filtering, while 14 KB of Flash holds multiple interface routines. Its 1.8 V to 5.5 V range enables use in mixed-voltage embedded networks, subject to correct level translation. The extended-temperature version also supports gateways installed in industrial cabinets, vehicle enclosures or outdoor equipment housings.
추천
Battery-Powered Measurement Instrument
The PIC16F1517-E/P supports compact measurement instruments that require several interfaces without a large application processor. Its 10-bit ADC handles basic analog measurements, 512 bytes of RAM supports working buffers, and the XLP-oriented family design targets low-power operation. The microcontroller can use EUSART for configuration and reporting, MI2C or SPI for external sensors, and the two CCP modules for timing or excitation control. The −40 °C to +125 °C grade makes the device suitable for field equipment exposed to substantial ambient-temperature changes.
추천
추천 제품 요약
엔지니어링 참조 데이터: PIC16F1517-E/P — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | PIC16F1517-I/P | PIC16F1518-E/P | PIC16F1518-I/P | PIC16F1519-E/P | PIC16F1519-I/P |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 40-pin PDIP | 40-pin PDIP | 40-pin PDIP | 40-pin PDIP | 40-pin PDIP | 40-pin PDIP |
| CPU Type | 8-bit PIC16F | 8-bit PIC16F | 8-bit PIC16F | 8-bit PIC16F | 8-bit PIC16F | 8-bit PIC16F |
| Maximum CPU Frequency | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz |
| Program Memory | 14 KB Flash, 8K × 14 words | 14 KB Flash, 8K × 14 words | Approximately 16 KB Flash | Approximately 16 KB Flash | Approximately 16 KB Flash | Approximately 16 KB Flash |
| Operating Voltage Range | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V |
| Operating Temperature Range | −40 °C to +125 °C | −40 °C to +85 °C | −40 °C to +125 °C | −40 °C to +85 °C | −40 °C to +125 °C | −40 °C to +85 °C |
| ADC Resolution | 10 bits | 10 bits | 10 bits | 10 bits | 10 bits | 10 bits |
| Serial Interfaces | SPI, MI2C and EUSART | SPI, MI2C and EUSART | SPI, MI2C and EUSART | SPI, MI2C and EUSART | SPI, MI2C and EUSART | SPI, MI2C and EUSART |
| CCP Modules | 2 | 2 | 2 | 2 | 2 | 2 |
주요 차별점
- Higher temperature ceiling than the industrial-grade counterpart (vs PIC16F1517-I/P)
- More Flash capacity in the PIC16F1518 same-package option (vs PIC16F1518-E/P)
- More Flash capacity in the PIC16F1519 same-package option (vs PIC16F1519-E/P)
설계 노트
Use the exact 40-pin PDIP lead arrangement in Microchip Data Sheet 40001452F when creating the schematic symbol and PCB footprint. Keep the programming connector accessible, provide a clean VDD and VSS connection, and place the required decoupling capacitors close to their associated supply pins. Although the -E/P package is through-hole, short analog and serial traces should still be routed away from high-current switching nodes to reduce coupling into the 10-bit ADC and communication interfaces.
Estimate the regulator and MCU dissipation before fixing the supply architecture. For a linear supply, the estimated MCU dissipation is approximately (VIN − VDD) × ILOAD plus internal overhead; for example, 5.5 V input, 3.3 V output and 10 mA load gives approximately 22 mW before internal losses. Verify the resulting junction temperature across the −40 °C to +125 °C ambient range and account for regulator efficiency, transient response and the source current available during startup.
Do not treat all PIC16F1517 order codes as mechanically interchangeable. The -E/P target is a 40-pin PDIP, while other suffix combinations can use 44-pin TQFP or other package forms. Similarly, changing from -E to -I reduces the upper temperature rating from +125 °C to +85 °C. Before substitution, compare the package drawing, pin functions, memory capacity, voltage range, configuration words and existing firmware requirements against the manufacturer ordering information.
Assign analog inputs deliberately rather than treating all digital-capable pins as equivalent ADC channels. Follow the datasheet's recommended analog input topology, keep the analog source impedance within the ADC sampling limits, and connect unused analog inputs according to the device guidance. For SPI, MI2C and EUSART traffic, route signals away from the crystal or internal-oscillator clock path and use a ground reference that remains continuous beneath the communication section.
규정 준수 정보
The -E suffix denotes the extended-temperature grade, not automotive qualification. RoHS, REACH, lead-free, halogen-free and conflict-minerals status require confirmation from the manufacturer's current product compliance documentation.