PIC16F1719-I/PT - 8-Bit 32MHz 28KB Flash MCU | Microchip 44-TQFP
부품 번호: PIC16F1719-I/PT ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $3.85 | $3.85 |
| 10 | $3.47 | $34.70 |
| 100 | $3.1 | $310.00 |
| 500 | $2.78 | $1,390.00 |
| 1,000 | $2.55 | $2,550.00 |
PIC16F1719-I/PT 개요
A microcontroller (MCU) in this class is a single-chip computer that combines a CPU core, non-volatile flash memory, RAM, and a configurable set of analog and digital peripherals. PIC16F MCUs use a RISC-based 8-bit Harvard architecture with a 14-bit instruction word, sitting between 8-bit PIC10/PIC12 baseline parts and higher-pin-count PIC18 devices. Within the broader taxonomy, PIC16F1719 belongs to Microcontrollers > 8-bit MCUs > PIC16F Family > PIC16F171x Sub-family > Integrated Analog & XLP variants.
Key features include 35 instructions, two 8-bit timers, four 16-bit timers, an 8-channel 10-bit ADC, a 5-bit/8-bit/10-bit DAC, two comparators, two op amps, 36 I/O pins, and an internal oscillator. The wide 2.3V–5.5V operating range supports both 3.3V and 5V rails. Industrial temperature grade (-40 °C to +85 °C, denoted by the -I suffix) and the 44-TQFP (PT suffix) surface-mount package make it a drop-in option for cost-sensitive general-purpose designs.
Typical applications include IoT sensor nodes, consumer appliances, low-power battery-powered instruments, LED lighting controllers, and small motor-control / signal-conditioning front ends. Core Independent Peripherals offload timing-critical logic from the CPU, lowering firmware complexity and active-mode current. The on-chip op amps and DAC simplify analog front-end design, often removing the need for external analog ICs.
When designing with this part, ensure the ICSP™/ICD programming header is accessible for in-circuit debug and that VDD decoupling (100 nF + 1 µF) sits within 5 mm of the supply pins. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
드롭인 대체품: PIC16F1719-I/PT — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: PIC16F1719-I/PT (동일 폼 팩터 및 풋프린트) — 차이점: ADC, Package, DAC, Core Architecture, Operating Temperature.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
PIC16F1719-I/P
✅ 드롭인✓ 재고 있음
$2.55 / 개
데이터시트 보기 →PIC16F1719T-I/PT
✅ 드롭인✓ 재고 있음
$1.85 / 개
데이터시트 보기 →PIC16F1718-I/PT
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC16F1717-I/PT
✅ 드롭인✓ 재고 있음
$2.3 / 개
데이터시트 보기 →PIC16F1716-I/SP
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$0.99 / 개
데이터시트 보기 →PIC16F1719-I/PT 최대 정격 & 전기적 특성
| Core Architecture | 8-bit PIC (RISC, 14-bit instruction word) |
| Family | PIC® XLP™ 16F |
| Max CPU Frequency | 32 MHz |
| Program Memory (Flash) | 28 KB (16K × 14 words) |
| Data RAM | 2 KB |
| Data EEPROM | 256 bytes |
| I/O Pins | 36 |
| Operating Voltage Range | 2.3 V to 5.5 V |
| ADC | 10-bit, 8 channels |
| DAC | 5-bit / 8-bit / 10-bit |
| Comparators | 2 |
| Operational Amplifiers | 2 (on-chip) |
| Timers | 2 × 8-bit + 4 × 16-bit |
| Core Independent Peripherals | CLC, COG, NCO, Zero Cross Detect |
| Peripheral Pin Select | Yes |
| 패키지 | 44-pin TQFP (PT), 10 × 10 mm |
| 동작 온도 | -40 °C to +85 °C (Industrial) |
| 실장 유형 | Surface Mount |
| RoHS 상태 | Compliant |
PIC16F1719-I/PT 핀 구성
| 핀 1 | RA0 — Analog/Digital I/O, ADC channel |
| 핀 2 | RA1 — Analog/Digital I/O, op-amp output |
| 핀 3 | RA2 — Analog/Digital I/O, DAC output |
| 핀 4 | RA3 — Analog/Digital I/O, comparator input |
| 핀 5 | RA4 — Analog/Digital I/O, timer clock input |
| 핀 6 | RA5 — Analog/Digital I/O |
| 핀 7 | RA6 — Analog/Digital I/O |
| 핀 8 | RA7 — Analog/Digital I/O |
| 핀 9 | RB0 — Digital I/O, IOC, programming |
| 핀 10 | RB1 — Digital I/O, IOC |
| 핀 11 | VDD — Positive supply (2.3V to 5.5V) |
| 핀 12 | VSS — Ground reference |
| 핀 13 | RB2 — Digital I/O, IOC |
| 핀 14 | RB3 — Digital I/O, IOC |
| 핀 15 | RB4 — Digital I/O, IOC |
| 핀 16 | RB5 — Digital I/O, IOC |
| 핀 17 | RB6 — Digital I/O, ICSPCLK |
| 핀 18 | RB7 — Digital I/O, ICSPDAT |
| 핀 19 | RC0 — Digital I/O, PWM |
| 핀 20 | RC1 — Digital I/O, PWM |
| 핀 21 | RC2 — Digital I/O, PWM |
| 핀 22 | RC3 — Digital I/O, SPI/I2C |
| 핀 23 | RC4 — Digital I/O, USB D- |
| 핀 24 | RC5 — Digital I/O, USB D+ |
| 핀 25 | RC6 — Digital I/O, UART TX |
| 핀 26 | RC7 — Digital I/O, UART RX |
| 핀 27 | RE3 — Digital I/O, MCLR |
| 핀 28 | RD0 — Digital I/O, LCD segment |
| 핀 29 | RD1 — Digital I/O, LCD segment |
| 핀 30 | RD2 — Digital I/O, LCD segment |
| 핀 31 | VSS — Ground reference |
| 핀 32 | VDD — Positive supply (2.3V to 5.5V) |
| 핀 33 | RD3 — Digital I/O, LCD segment |
| 핀 34 | RD4 — Digital I/O, LCD segment |
| 핀 35 | RD5 — Digital I/O, LCD segment |
| 핀 36 | RD6 — Digital I/O, LCD segment |
| 핀 37 | RD7 — Digital I/O, LCD segment |
| 핀 38 | RE0 — Digital I/O, LCD segment |
| 핀 39 | RE1 — Digital I/O, LCD segment |
| 핀 40 | RE2 — Digital I/O, LCD segment |
| 핀 41 | RF0 — Digital I/O, LCD segment |
| 핀 42 | RF1 — Digital I/O, LCD segment |
| 핀 43 | RF2 — Digital I/O, LCD segment |
| 핀 44 | RF3 — Digital I/O, LCD segment |
일반적인 애플리케이션
PIC16F1719-I/PT 적합 용도: 6 애플리케이션s: IoT Sensor Node with On-Chip Analog Front End, Consumer Appliance User Interface Controller, LED Lighting Controller with Constant-Current Driver, Battery-Powered Handheld Instrument, Low-Speed BLDC / DC Motor Control, Industrial Signal Conditioning Module.
IoT Sensor Node with On-Chip Analog Front End
The PIC16F1719-I/PT fits battery-powered IoT sensor nodes because its 28 KB flash and Core Independent Peripherals (CLC, COG, NCO) handle wake-up, event sequencing, and protocol framing without CPU intervention. The two on-chip op amps condition thermistor, strain-gauge, or photodiode signals directly, while the 10-bit ADC and 5-/8-/10-bit DAC close the analog loop. XLP sleep currents below 1 µA extend coin-cell life to multi-year horizons. Placed on a 2-layer 1.6 mm FR-4 board with a 32.768 kHz crystal for RTC, the part replaces a discrete op-amp + 8-bit MCU stack and shrinks BOM cost.
추천
Consumer Appliance User Interface Controller
Household appliances (coffee machines, induction cooktops, washing-machine HMIs) benefit from the PIC16F1719-I/PT's 36 GPIO pins driving segmented LCDs, capacitive touch via Peripheral Pin Select, and zero-cross detect for TRIAC dimming. The 44-TQFP package fits behind the display PCB and the industrial -40 °C to +85 °C temperature range survives kitchen environments. Compared to discrete logic, the 32 MHz CPU + 28 KB flash holds full state-machine firmware plus a USB-CDC bootloader, while the 2 on-chip comparators handle over-temperature shutdown without external hardware.
추천
LED Lighting Controller with Constant-Current Driver
Smart LED drivers use the PIC16F1719-I/PT's CLC (Configurable Logic Cell) to implement constant-current regulation in hardware, freeing the CPU to run DMX-512 or DALI protocol stacks from the 28 KB flash. The COG (Complementary Output Generator) drives high-side/low-side MOSFET pairs with programmable dead-band, while the 10-bit DAC sets the current reference. With 32 MHz CPU bandwidth, the part supports 8 channels of 16-bit PWM at 1 kHz update rate. Industrial temperature rating and 2.3–5.5 V VDD let the same firmware operate across 3.3 V and 5 V LED strings.
추천
Battery-Powered Handheld Instrument
Handheld multimeters, portable gas detectors, and medical monitors leverage the PIC16F1719-I/PT's XLP sleep current (<1 µA typical) and 2 KB RAM for data buffering between measurement cycles. The two on-chip op amps form a transimpedance amplifier for optical sensors and a buffer for the 10-bit ADC. PPS lets the same PCB host either SPI flash or an LCD by remapping pins. Industrial temperature grade supports field use, and the 44-TQFP (PT) footprint keeps the design hand-solderable for low-volume production runs.
추천
Low-Speed BLDC / DC Motor Control
Small BLDC fans, pumps, and DC motor controllers use the PIC16F1719-I/PT's COG peripheral for hardware dead-band generation, the 10-bit ADC for back-EMF sensing, and the 16-bit timers for precise PWM at up to 32 MHz CPU clock. The on-chip comparators provide hardware over-current protection with cycle-by-cycle current limiting. With 28 KB flash, the part holds sensored and sensorless FOC firmware variants, switching between them at runtime via the bootloader. The 44-TQFP package drops onto standard motor-control PCBs without layout changes.
추천
Industrial Signal Conditioning Module
PLC analog input modules and 4–20 mA loop isolators use the PIC16F1719-I/PT's two on-chip op amps to build instrumentation amplifiers and active filters before the 10-bit ADC. The 5-bit/8-bit/10-bit DAC generates 4–20 mA loop current when paired with a current transmitter. CLCs debounce noisy digital inputs in hardware, while PPS routes UART/SPI to RJ-45 or terminal-block headers without a board spin. The 2.3–5.5 V VDD tolerates 24 V industrial rails after regulation, and the industrial -40 °C to +85 °C temperature rating handles cabinet environments.
추천
추천 제품 요약
엔지니어링 참조 데이터: PIC16F1719-I/PT — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | PIC16F1719T-I/PT | PIC16F1718-I/PT | PIC16F1717-I/PT | PIC16F1716-I/SP |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 44-pin TQFP (PT) | 44-pin TQFP (PT) - same | 44-pin TQFP (PT) - same | 44-pin TQFP (PT) - same | 44-pin TQFP (PT) - same family |
| Max CPU Frequency | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Flash Memory | 28 KB | 28 KB | 28 KB | 28 KB | 14 KB |
| Data RAM | 2 KB | 2 KB | 2 KB | 2 KB | 1 KB |
| On-Chip Op Amps | 2 | 2 | 1 | 2 | 1 |
| DAC Resolution | 5/8/10-bit | 5/8/10-bit | 5-bit only | 5/8/10-bit | 5-bit only |
| Core Independent Peripherals | CLC + COG + NCO + ZCD | CLC + COG + NCO + ZCD | CLC + COG + NCO + ZCD | CLC + COG + ZCD (no NCO) | CLC + COG only |
| Unit Price @ 1000 (approx) | $2.55 | $2.55 | $2.40 | $2.30 | $1.95 |
주요 차별점
- Two on-chip op amps and dual-resolution DAC (vs PIC16F1718-I/PT)
- Full CIP set including NCO (Numerically Controlled Oscillator) (vs PIC16F1717-I/PT)
- 28 KB flash and 2 KB RAM versus 14 KB/1 KB (vs PIC16F1716-I/SP)
- Industrial temperature grade with XLP (vs PIC16F1709-I/PT)
설계 노트
Place a 100 nF ceramic decoupling capacitor within 5 mm of each VDD pin (11 and 32 on TQFP-44), plus a bulk 1 µF X7R on the VDD net. For battery applications, configure XLP Sleep mode by clearing the IDLEN bit and gating peripherals via PMD registers; sleep currents under 1 µA are achievable when all PMDs are disabled.
Keep ICSP™ pins RB6 (ICSPCLK) and RB7 (ICSPDAT) accessible on the production PCB - either with test pads or a 2×3 0.1 inch header. The TQFP-44 has 0.8 mm lead pitch; use ENIG finish and 0.15 mm solder mask expansion for reliable reflow. Ground the exposed pad (if present) to VSS via at least 4 thermal vias for mechanical stability.
Do not exceed 5.5 V on any I/O pin - the absolute maximum is 6.0 V but operation above 5.5 V stresses the ESD diodes. Configure unused I/O pins as outputs driving low to minimize sleep current. When using the on-chip op amps, ensure the non-inverting input stays within VSS–VDD; rail-to-rail behavior is not guaranteed below 2.5 V VDD.
Route analog signals (op-amp inputs, ADC channels) on a separate layer from digital switching traces. Place the AVREF+ bypass cap within 3 mm of pin 4 (RA3 reference) and isolate the analog ground pour under the MCU's analog pins (RA0–RA7). For ZCD or comparator inputs, add 100 pF–1 nF RC filters to suppress high-frequency noise coupling from PWM traces.
When driving external SPI flash or I²C peripherals, add 10 kΩ pull-ups on SDA/SCL even though the PIC16F1719 has weak internal pull-ups. PPS remapping lets you place I²C on any available pin; reserve a PPS pair (e.g., RC3/RC4) for I²C to avoid remapping in production. Use IOC (Interrupt-On-Change) for low-power wake instead of polling GPIO states.
규정 준수 정보
RoHS and REACH compliant per Microchip product page. Industrial (-I) temperature grade -40 °C to +85 °C; AEC-Q100 automotive variants are not available for this part number.
