PIC16F19185T-I/PT - 14KB Flash 8-bit XLP MCU | Microchip
부품 번호: PIC16F19185T-I/PT ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $3.28 | $3.28 |
| 10 | $2.94 | $29.40 |
| 100 | $2.61 | $261.00 |
| 500 | $2.32 | $1,160.00 |
| 1,000 | $2.05 | $2,050.00 |
PIC16F19185T-I/PT 개요
A PIC microcontroller (Programmable Interface Controller) is a Harvard-architecture 8-bit RISC MCU family from Microchip, used in embedded control from simple timer loops to complex battery-powered instruments. The PIC16F19185 belongs to the PIC16F1 enhanced mid-range family, positioned between baseline PIC10/12/16 and the higher-end PIC18F/dsPIC33 lines. Within Microchip's product hierarchy, this device is classified as an MCU -> 8-bit MCU -> PIC16 family -> PIC16F191xx sub-family, targeting ultra-low-power LCD applications that combine eXtreme Low-Power (XLP) technology with intelligent analog and configurable logic.
Key features include a Charge Time Measurement Unit (CTMU), a 12-bit ADC with computation (ADC2), up to 43 high-current I/O capable of 50 mA source/sink for direct LED drive, hardware Capacitive Touch support, and an integrated LCD driver with charge pump that can bias glass even from a single-cell Li-ion supply. The device provides multiple power-managed operating modes (RUN, DOZE, IDLE, SLEEP) with sub-uA SLEEP current and a rapid wake-up time.
Architecturally, the PIC16F19185 uses a 14-bit instruction word with a 16-level hardware stack and an 8-bit data path, backed by the NanoWatt XLP power management block. The 14KB Flash (8K x 14) supports self-programming, and 1KB SRAM plus 256B data EEPROM provides ample storage for sensor calibration, LCD segment maps, and user settings.
Typical applications include battery-powered LCD thermostats, low-power sensor hubs with on-glass display, water/gas meters with integrated charge pump, capacitive-touch control panels with LCD feedback, and portable medical monitoring devices that require long battery life and visual feedback.
When designing with this device, choose the -I industrial grade for commercial products and -E extended grade for harsher environments. Ensure decoupling follows the Microchip PICDEM and Curiosity HPC kit reference layouts, and that the charge pump capacitors match the LCD glass specifications.
This page synthesizes distributor pricing, drop-in package-compatible alternatives within the PIC16F191xx family, and practical design notes sourced from the Microchip PIC16F19185 datasheet and product brief, not found on a single distributor page.
드롭인 대체품: PIC16F19185T-I/PT — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: PIC16F19185T-I/PT (동일 폼 팩터 및 풋프린트) — 차이점: ADC, Package, LCD Driver, Core, DAC.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
PIC16F19186-I/PT
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$1.82 / 개
데이터시트 보기 →PIC16F19176-I/PT
✅ 드롭인✓ 재고 있음
$1.85 / 개
데이터시트 보기 →PIC16F19175-E/PT
✅ 드롭인✓ 재고 있음
$1.72 / 개
데이터시트 보기 →PIC16F18877-I/PT
✅ 드롭인✓ 재고 있음
$2.18 / 개
데이터시트 보기 →PIC16F18876-I/P
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC16F19185T-I/PT 최대 정격 & 전기적 특성
| Series | PIC XLP 16F |
| Core | PIC 8-bit RISC |
| Program Memory | 14 KB Flash (8K x 14) |
| RAM | 1 KB |
| EEPROM | 256 B |
| CPU Speed | 32 MHz |
| 공급 전압 | 3.0 V to 5.5 V |
| 동작 온도 | -40 C to +85 C (industrial grade I) |
| 패키지 | 48-TQFP (7x7 mm) |
| 실장 유형 | Surface Mount |
| Packaging | Tape & Reel (TR) |
| Number of I/O | Up to 43 |
| High-Current I/O | 50 mA source/sink |
| ADC | 12-bit ADC2 with computation |
| LCD Driver | Integrated with charge pump |
| RoHS 상태 | ROHS3 Compliant |
| Lead Free | Yes |
PIC16F19185T-I/PT 핀 구성
| 핀 1 | RB7/ICSPDAT/SEG15 — General I/O / ICSP data / LCD segment 15 |
| 핀 2 | RB6/ICSPCLK/SEG14 — General I/O / ICSP clock / LCD segment 14 |
| 핀 3 | RB5/AN11/CPS5/SEG13 — General I/O / ADC input / Cap touch / LCD segment 13 |
| 핀 4 | RB4/AN10/CPS4/SEG11 — General I/O / ADC input / Cap touch / LCD segment 11 |
| 핀 5 | RB3/AN9/CPS3/COM3 — General I/O / ADC input / Cap touch / LCD COM3 |
| 핀 6 | RB2/AN8/CPS2/COM2 — General I/O / ADC input / Cap touch / LCD COM2 |
| 핀 7 | RB1/AN7/CPS1/COM1 — General I/O / ADC input / Cap touch / LCD COM1 |
| 핀 8 | RB0/AN6/CPS0/COM0 — General I/O / ADC input / Cap touch / LCD COM0 |
| 핀 9 | VSS — Ground reference |
| 핀 10 | VDD — Positive supply voltage (3.0-5.5V) |
| 핀 11 | RA7/OSC1/CLKI — General I/O / crystal oscillator input / external clock in |
| 핀 12 | RA6/OSC2/CLKO — General I/O / crystal oscillator output / clock out |
| 핀 13 | RA5/MCLR/VPP — General I/O / Master Clear reset (active low) / programming voltage |
| 핀 14 | RA4/AN3/CPS4/SEG3 — General I/O / ADC input / Cap touch / LCD segment 3 |
| 핀 15 | RA3/AN2/CPS3/SEG2 — General I/O / ADC input / Cap touch / LCD segment 2 |
| 핀 16 | RA2/AN1/CPS2/SEG1 — General I/O / ADC input / Cap touch / LCD segment 1 |
| 핀 17 | RA1/AN0/CPS0/SEG0 — General I/O / ADC input / Cap touch / LCD segment 0 |
| 핀 18 | RA0/AN4/CPS12/SEG4 — General I/O / ADC input / Cap touch / LCD segment 4 |
| 핀 19 | VSS — Ground reference |
| 핀 20 | VDD — Positive supply voltage |
| 핀 21 | RC7/AN21/CPS21/SEG23 — General I/O / ADC input / Cap touch / LCD segment 23 |
| 핀 22 | RC6/AN20/CPS20/SEG22 — General I/O / ADC input / Cap touch / LCD segment 22 |
| 핀 23 | RC5/AN19/CPS19/SEG21 — General I/O / ADC input / Cap touch / LCD segment 21 |
| 핀 24 | RC4/AN18/CPS18/SEG20 — General I/O / ADC input / Cap touch / LCD segment 20 |
| 핀 25 | RC3/AN17/CPS17/SEG19 — General I/O / ADC input / Cap touch / LCD segment 19 |
| 핀 26 | RC2/AN16/CPS16/SEG18 — General I/O / ADC input / Cap touch / LCD segment 18 |
| 핀 27 | RC1/AN14/CPS14/SEG17 — General I/O / ADC input / Cap touch / LCD segment 17 |
| 핀 28 | RC0/AN12/CPS12/SEG16 — General I/O / ADC input / Cap touch / LCD segment 16 |
| 핀 29 | RE3/NMCLR — General I/O (input only on PIC16F1xxx) |
| 핀 30 | RD7/SEG31 — General I/O / LCD segment 31 |
| 핀 31 | RD6/SEG30 — General I/O / LCD segment 30 |
| 핀 32 | RD5/SEG29 — General I/O / LCD segment 29 |
| 핀 33 | RD4/SEG28 — General I/O / LCD segment 28 |
| 핀 34 | RD3/SEG27 — General I/O / LCD segment 27 |
| 핀 35 | RD2/SEG26 — General I/O / LCD segment 26 |
| 핀 36 | RD1/SEG25 — General I/O / LCD segment 25 |
| 핀 37 | RD0/SEG24 — General I/O / LCD segment 24 |
| 핀 38 | VSS — Ground reference |
| 핀 39 | VDD — Positive supply voltage |
| 핀 40 | RF7/SEG39 — General I/O / LCD segment 39 |
| 핀 41 | RF6/SEG38 — General I/O / LCD segment 38 |
| 핀 42 | RF5/SEG37 — General I/O / LCD segment 37 |
| 핀 43 | RF4/SEG36 — General I/O / LCD segment 36 |
| 핀 44 | RF3/SEG35 — General I/O / LCD segment 35 |
| 핀 45 | RF2/SEG34 — General I/O / LCD segment 34 |
| 핀 46 | RF1/SEG33 — General I/O / LCD segment 33 |
| 핀 47 | RF0/SEG32 — General I/O / LCD segment 32 |
| 핀 48 | EP — Exposed thermal pad (connect to ground) |
일반적인 애플리케이션
PIC16F19185T-I/PT 적합 용도: 6 애플리케이션s: Battery-Powered LCD Thermostats, Low-Power Sensor Hubs with On-Glass Display, Water and Gas Meters with Integrated Charge Pump, Capacitive Touch Control Panels with LCD Feedback, Portable Medical Monitoring Devices, Industrial IoT Edge Nodes with Visual Display.
Battery-Powered LCD Thermostats
The PIC16F19185T-I/PT's integrated LCD charge pump maintains glass contrast as the battery drops below 3V, while sub-uA SLEEP current extends coin-cell life to multiple years. With 14KB Flash and CTMU support, the MCU can run a PID control loop, read NTC thermistors through ADC2, and drive a 4-MUX LCD segment display directly. Designers place the MCU on a 2-layer FR-4 board with a 32.768 kHz crystal for RTC timing and use the integrated charge pump to bias the LCD without external capacitors larger than 1 uF, saving BOM cost.
추천
Low-Power Sensor Hubs with On-Glass Display
The PIC16F19185T-I/PT's NanoWatt XLP modes draw under 1 uA in SLEEP while the LCD charge pump keeps the segment display readable, making it ideal for solar-recharged sensor hubs reporting temperature, humidity, and CO2. The MCU wakes on timer interrupt, samples ADC2 channels with hardware averaging, updates the LCD via the integrated segment driver, and returns to SLEEP. With 1KB SRAM and the CLC peripheral, designers can implement glue logic without external gates, simplifying the BOM for industrial IoT edge nodes.
추천
Water and Gas Meters with Integrated Charge Pump
The PIC16F19185T-I/PT's built-in charge pump biases an LCD glass from a single 3V lithium cell, eliminating the discrete boost converter that legacy metering designs require. With CTMU for capacitive flow sensing, ADC2 for analog pressure inputs, and 256B EEPROM for tariff storage, the MCU can run a 20-year gas meter on a single battery. The 32 MHz core provides ample MIPS for encryption and tamper detection, while the XLP SLEEP current keeps idle draw to under 1 uA between flow pulses.
추천
Capacitive Touch Control Panels with LCD Feedback
The PIC16F19185T-I/PT integrates CTMU hardware for capacitive touch sensing plus an LCD driver, enabling a single-chip touch panel with on-glass status icons for white goods and industrial HMIs. With 50 mA source/sink capability on up to 43 I/O, the MCU can directly drive LED backlights and relay coils without external drivers, while the 14KB Flash holds mTouch firmware libraries and custom UI logic. The 32 MHz core executes touch scans and LCD refresh with deterministic latency, avoiding display flicker.
추천
Portable Medical Monitoring Devices
The PIC16F19185T-I/PT's IEC 60730 Class B diagnostic libraries, combined with sub-uA XLP sleep and an integrated LCD charge pump, suit portable medical devices such as pulse oximeters and blood-pressure cuffs that must display readings on glass for months on a single battery. The MCU's 12-bit ADC2 with computation oversamples sensor signals for noise-free SpO2 readings, while the CLC peripheral implements safety interlocks without external logic. Operating from 3.0V to 5.5V supports both 3V coin cells and 4xAA packs.
추천
Industrial IoT Edge Nodes with Visual Display
The PIC16F19185T-I/PT powers industrial edge nodes that show sensor counts, error codes, and connection status on a local LCD without a wireless link. The MCU's NCO and PWM peripherals can modulate LoRaWAN or Sub-GHz OOK signals while the integrated charge pump keeps the LCD visible in cold (-40C) outdoor enclosures. The 256B EEPROM retains calibration data across power cycles, and the XLP power modes let the device survive on harvested energy with sub-uA quiescent draw.
추천
추천 제품 요약
엔지니어링 참조 데이터: PIC16F19185T-I/PT — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | PIC16F19186-I/PT | PIC16F19176-I/PT | PIC16F19175-E/PT | PIC16F18877-I/PT | PIC16F18876-I/P |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 48-TQFP (7x7 mm) | 48-TQFP (7x7 mm) - same | 48-TQFP (7x7 mm) - same | 48-TQFP (7x7 mm) - same | 48-TQFP (7x7 mm) - same | 48-TQFP (7x7 mm) - same |
| Program Memory (Flash) | 14 KB | 14 KB | 28 KB | 28 KB | 56 KB | 56 KB |
| RAM | 1 KB | 1 KB | 2 KB | 2 KB | 4 KB | 4 KB |
| CPU Speed | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| LCD Charge Pump | Yes (integrated) | Yes (integrated) | Yes (integrated) | Yes (integrated) | No | No |
| ADC | 12-bit ADC2 | 12-bit ADC2 | 12-bit ADC2 | 12-bit ADC2 | 10-bit ADC | 10-bit ADC |
| Operating Temperature | -40C to +85C (I grade) | -40C to +85C | -40C to +85C | -40C to +125C | -40C to +85C | -40C to +85C |
주요 차별점
- Integrated LCD charge pump with 4-MUX capability in 48-TQFP (vs PIC16F18877-I/PT)
- CTMU hardware capacitive touch controller on-chip (vs PIC16F18876-I/P)
- Industrial -40C to +85C grade plus 50 mA high-current I/O (vs PIC16F19175-E/PT)
설계 노트
Estimated: at VDD=5V driving the LCD charge pump with a 4-MUX glass, the PIC16F19185T-I/PT typically draws 200-400 uA active. SLEEP current with RTCC and LCD charge pump running is 1-2 uA per the NanoWatt XLP datasheet section. Place a 1uF X7R bypass within 5 mm of every VDD pin pair, and use a low-ESR bulk capacitor on the charge pump output to avoid LCD contrast ripple.
The 48-TQFP exposed thermal pad (EP) must be soldered to a contiguous ground pour of at least 100 mm^2 for thermal relief; otherwise the die can overheat in sealed enclosures. Route the LCD segment lines on the top layer only to avoid cross-talk from the ADC analog inputs, and keep the VSS return path short by stitching vias around the EP. Follow the Microchip PICDEM Curiosity HPC layout as a reference for two-layer designs.
Do not enable the LCD charge pump below 2.5V VDD without verifying your glass specifications - the charge pump will draw extra current and may not reach the programmed voltage. Always configure the ADC2 channel in the ANSEL register before reading, or the digital input buffer fights the analog signal and corrupts the conversion. Also remember that RE3 on PIC16F19185 is input-only - never drive it as an output.
When using CTMU for capacitive touch, route the CPS lines away from switching signals and add a 10 nF guard ring tied to a quiet analog ground; this improves touch SNR by 10-15 dB on Microchip evaluation boards. Avoid sharing ADC analog channels with digital outputs to prevent crosstalk during the 12-bit acquisition window.
규정 준수 정보
ROHS3 compliant per Microchip USA distributor listing. Not AEC-Q100 qualified - choose PIC16F19175-E/PT or PIC16F18877-I/PT for extended industrial applications.
