PIC16LF1519-I/PT - 28KB Flash 8-bit MCU, 20MHz, TQFP-44 | Microchip
부품 번호: PIC16LF1519-I/PT ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $2.41 | $2.41 |
| 10 | $2.18 | $21.80 |
| 100 | $1.84 | $184.00 |
| 500 | $1.59 | $795.00 |
| 1,000 | $1.42 | $1,420.00 |
PIC16LF1519-I/PT 개요
An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and peripherals on one die; it sits within the broader taxonomy of microcontroller -> embedded processor -> semiconductor. PIC16F1xxx family MCUs from Microchip are popular for low-power, cost-sensitive embedded control where deterministic interrupt response, simple peripherals, and long product lifecycles outweigh the need for higher MIPS.
Key features include nanoWatt XLP sleep current as low as sub-uA in deep sleep, multiple low-power modes (Sleep, Idle, Doze), an integrated 10-bit ADC with up to 28 channels, Enhanced Universal Synchronous/Asynchronous Receiver/Transmitter (EUSART), two MSSP (SPI/I2C) modules, and 17 I/O pins with interrupt-on-change support. The 28KB Flash supports self-programming for bootloader and field updates.
The architecture uses a 14-bit instruction word with a hardware multiplier, eight-level hardware stack, and a 31-instruction set optimized for C and assembly development. The device supports in-circuit debugging via ICD 3 / PICkit 4 and programming with the MPLAB X IDE and XC8 compiler, giving engineers a low-cost, mature toolchain.
Typical applications include IoT sensor nodes, battery-powered instrumentation, consumer electronics human-interface controllers, HVAC control boards, automotive body and accessory subsystems, and industrial sensor conditioning. Designers typically pair the PIC16LF1519 with low-power wireless modules, sensor front-ends, and small LCDs.
When designing with this MCU, budget for the on-chip 10-bit ADC and consider external reference ICs where absolute accuracy matters. Use the brown-out reset and watchdog timer for unattended deployments to recover from supply or code-flow faults.
This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet alone.
드롭인 대체품: PIC16LF1519-I/PT — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: PIC16LF1519-I/PT (동일 폼 팩터 및 풋프린트) — 차이점: I/O Pins, Package, Core Architecture, Operating Temperature, MSL Level.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
PIC16F1519-I/PT
✅ 드롭인✓ 재고 있음
$2.18 / 개
데이터시트 보기 →PIC16LF1519-I/P
✅ 드롭인✓ 재고 있음
$1.99 / 개
데이터시트 보기 →PIC16LF1519-E/PT
✅ 드롭인✓ 재고 있음
$2.46 / 개
데이터시트 보기 →PIC16LF1518-I/PT
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC16LF1517-I/PT
✅ 드롭인✓ 재고 있음
$1.53 / 개
데이터시트 보기 →PIC16LF1519-I/PT 최대 정격 & 전기적 특성
| Core Architecture | PIC16 Enhanced Mid-Range 8-bit |
| Program Memory (Flash) | 28 KB (16K x 14) |
| SRAM | 1024 bytes |
| 최대 클록 주파수 | 20 MHz |
| Supply Voltage (VDD) | 1.8 V to 3.6 V |
| I/O Pins | 36 (per 44-pin TQFP) |
| ADC | 10-bit, up to 28 channels |
| Timers | 8-bit and 16-bit (multiple) |
| Communication | 1x EUSART, 2x MSSP (SPI/I2C) |
| Low-Power Technology | nanoWatt XLP |
| 동작 온도 | -40 C to +85 C (industrial) |
| 패키지 | 44-pin TQFP (10x10 mm) |
| 실장 유형 | Surface Mount |
| MSL 레벨 | 3 (per JEDEC J-STD-020) |
| RoHS 상태 | Compliant |
| Debug Interface | ICSP (ICD/PICkit) |
PIC16LF1519-I/PT 핀 구성
| 핀 1 | MCLR/RE3 — Master Clear (reset) input or digital input only on PORTE bit 3 |
| 핀 2 | RA0 — PORTA bit 0 / analog input |
| 핀 3 | RA1 — PORTA bit 1 / analog input |
| 핀 4 | RA2 — PORTA bit 2 / analog input |
| 핀 5 | RA3 — PORTA bit 3 / analog input |
| 핀 6 | RA4 — PORTA bit 4 / analog input |
| 핀 7 | RA5 — PORTA bit 5 / analog input |
| 핀 8 | RA6 — PORTA bit 6 / analog input |
| 핀 9 | RA7 — PORTA bit 7 / analog input |
| 핀 10 | VSS — Ground reference |
| 핀 11 | VDD — Positive supply voltage (1.8 V - 3.6 V) |
| 핀 12 | RB0 — PORTB bit 0 / interrupt-on-change |
| 핀 13 | RB1 — PORTB bit 1 / interrupt-on-change |
| 핀 14 | RB2 — PORTB bit 2 / interrupt-on-change |
| 핀 15 | RB3 — PORTB bit 3 / interrupt-on-change |
| 핀 16 | RB4 — PORTB bit 4 / interrupt-on-change |
| 핀 17 | RB5 — PORTB bit 5 / interrupt-on-change |
| 핀 18 | RB6 — PORTB bit 6 / interrupt-on-change / ICSP CLK |
| 핀 19 | RB7 — PORTB bit 7 / interrupt-on-change / ICSP DAT |
| 핀 20 | VSS — Ground reference |
| 핀 21 | VDD — Positive supply voltage (1.8 V - 3.6 V) |
| 핀 22 | RC0 — PORTC bit 0 / analog input |
| 핀 23 | RC1 — PORTC bit 1 / analog input |
| 핀 24 | RC2 — PORTC bit 2 / analog input |
| 핀 25 | RC3 — PORTC bit 3 / analog input |
| 핀 26 | RC4 — PORTC bit 4 / analog input |
| 핀 27 | RC5 — PORTC bit 5 / analog input |
| 핀 28 | RC6 — PORTC bit 6 / analog input |
| 핀 29 | RC7 — PORTC bit 7 / analog input |
| 핀 30 | VSS — Ground reference |
| 핀 31 | VDD — Positive supply voltage (1.8 V - 3.6 V) |
| 핀 32 | RD0 — PORTD bit 0 |
| 핀 33 | RD1 — PORTD bit 1 |
| 핀 34 | RD2 — PORTD bit 2 |
| 핀 35 | RD3 — PORTD bit 3 |
| 핀 36 | RD4 — PORTD bit 4 |
| 핀 37 | RD5 — PORTD bit 5 |
| 핀 38 | RD6 — PORTD bit 6 |
| 핀 39 | RD7 — PORTD bit 7 |
| 핀 40 | VSS — Ground reference |
| 핀 41 | VDD — Positive supply voltage (1.8 V - 3.6 V) |
| 핀 42 | RE0 — PORTE bit 0 / analog input |
| 핀 43 | RE1 — PORTE bit 1 / analog input |
| 핀 44 | RE2 — PORTE bit 2 / analog input |
일반적인 애플리케이션
PIC16LF1519-I/PT 적합 용도: 7 애플리케이션s: Battery-Powered IoT Sensor Node, Consumer Electronics HMI Controller, HVAC Control Board, Automotive Body and Accessory Subsystem, Industrial Sensor Conditioning Module, Portable Medical Monitoring Accessory, Educational and Hobby Embedded Platform.
Battery-Powered IoT Sensor Node
The PIC16LF1519-I/PT fits battery-powered IoT sensor nodes because its 1.8-3.6 V supply aligns directly with single-cell alkaline, NiMH, or CR2032 chemistries, while nanoWatt XLP delivers sub-microampere sleep current to extend battery life into multi-year windows. The 10-bit ADC scans temperature, humidity, or motion sensors at low duty cycle, and the EUSART drives a low-power wireless module such as a sub-GHz transceiver. Designers place the MCU between the battery and sensor front-end, with brown-out reset and watchdog timer guarding unattended deployments. Unlike higher-MIPS Cortex-M parts, the 8-bit core keeps active current in the sub-mA range for duty-cycled wake/sleep sequences.
추천
Consumer Electronics HMI Controller
The PIC16LF1519-I/PT is well-suited to consumer HMI controllers, where 36 I/O pins drive keypads, LED indicators, rotary encoders, and segment LCDs without external glue logic. The 28 KB Flash stores state-machine code and small UI protocols, while the two MSSP peripherals handle I2C sensor expansion and SPI-driven LED drivers. Designers run the MCU at 3.3 V from a regulated rail and leverage the 20 MHz instruction rate to debounce inputs and refresh displays without visible lag. Compared to a discrete logic implementation, this single-chip approach cuts BOM cost and PCB area while adding firmware-driven flexibility.
추천
HVAC Control Board
The PIC16LF1519-I/PT suits HVAC control boards where multiple analog sensors (temperature, humidity, pressure) feed the 10-bit ADC while relay drivers switch fans, compressors, and valve actuators. The 1.8-3.6 V range plus 5 V-tolerant I/O pins (with proper level shifting) simplify interface to industrial 24 V control boards via optocouplers. Designers assign one MSSP to a Modbus RTU slave over RS-485 for building-automation integration and the other to an SPI EEPROM for logging setpoints. The industrial temperature grade (-40 C to +85 C) and nanoWatt XLP low-power modes keep idle quiescent current low during standby.
추천
Automotive Body and Accessory Subsystem
The PIC16LF1519-I/PT powers automotive body and accessory subsystems such as interior lighting, mirror controllers, and seat-position modules where 8-bit performance and low cost outweigh DSP requirements. The 28 KB Flash holds LIN-node firmware for slave communication with the body controller, and the 10-bit ADC reads current-sense amplifiers for short-circuit detection on LED strings. Designers run the MCU from a 12 V-derived 3.3 V rail and use the EUSART for LIN bus signaling at 19.2 kbps. For AEC-Q100 qualified designs in the same TQFP-44 footprint, Microchip offers the PIC16F1519-I/PT automotive-grade equivalent. The wide supply tolerance and watchdog timer support reliable unattended operation.
추천
Industrial Sensor Conditioning Module
The PIC16LF1519-I/PT serves industrial sensor-conditioning modules that digitize analog signals from strain gauges, load cells, or process transmitters and publish the result over Modbus RTU or 4-20 mA loops. The 10-bit ADC handles inputs from instrumentation front-ends, while the EUSART drives an RS-485 transceiver for multi-drop industrial networks. Designers exploit the 1.8-3.6 V range to power directly from a 24 V industrial bus via a small switching regulator, and the nanoWat XLP modes minimize quiescent draw during standby. Compared to discrete ADC-plus-MCU designs, this single-chip approach reduces component count and improves long-term reliability.
추천
Portable Medical Monitoring Accessory
The PIC16LF1519-I/PT fits portable medical monitoring accessories (pulse-oximeter cables, digital thermometer bases, low-cost spirometer dongles) that pair with a host tablet or phone over USB or Bluetooth. The 28 KB Flash stores calibration tables and small protocol handlers, and the nanoWatt XLP modes extend battery life during continuous monitoring sessions. The 10-bit ADC reads analog front-ends from photodiode or thermistor bridges, while the MSSP peripherals drive SPI displays or I2C health-sensor ICs. Designers run the MCU at 3.0-3.3 V from a rechargeable Li-ion cell and use brown-out reset to protect against deep-discharge conditions.
추천
Educational and Hobby Embedded Platform
The PIC16LF1519-I/PT is well-suited for educational embedded platforms and hobbyist development kits thanks to its simple 8-bit architecture, low-cost PICkit 4 debugger, and free MPLAB X IDE with XC8 compiler. The 28 KB Flash and 1024 B SRAM accommodate introductory C projects including state machines, interrupt-driven timers, and PWM motor control, while the 36 I/O pins expose enough peripherals for breadboard experiments. The 1.8-3.6 V range supports direct 3.3 V logic without level shifters, and the TQFP-44 package breaks out to standard 0.1 inch headers on popular development boards. Compared to ARM-based boards, this part lowers the learning curve for first-time embedded developers.
추천
추천 제품 요약
엔지니어링 참조 데이터: PIC16LF1519-I/PT — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | PIC16F1519-I/PT | PIC16LF1519-E/PT | PIC16LF1518-I/PT | PIC16LF1517-I/PT |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 44-pin TQFP (10x10 mm) | 44-pin TQFP (10x10 mm) - same | 44-pin TQFP (10x10 mm) - same | 44-pin TQFP (10x10 mm) - same | 44-pin TQFP (10x10 mm) - same |
| Flash Memory | 28 KB | 28 KB | 28 KB | 16 KB | 8 KB |
| SRAM | 1024 B | 1024 B | 1024 B | 1024 B | 512 B |
| Operating Voltage | 1.8 V to 3.6 V | 2.3 V to 5.5 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V |
| Max Clock Frequency | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz |
| Operating Temperature | -40 C to +85 C (industrial) | -40 C to +85 C | -40 C to +125 C (extended) | -40 C to +85 C | -40 C to +85 C |
| ADC | 10-bit | 10-bit | 10-bit | 10-bit | 10-bit |
| Low-Power Technology | nanoWatt XLP | nanoWatt XLP | nanoWatt XLP | nanoWatt XLP | nanoWatt XLP |
| Approx Unit Price (USD, qty 1) | 2.41 | 2.45 | 2.55 | 2.20 | 1.95 |
주요 차별점
- Lowest voltage operation in the family (vs PIC16F1519-I/PT)
- Highest Flash density in the LF151x TQFP family (vs PIC16LF1518-I/PT)
- Industrial-grade temperature option vs extended-grade (vs PIC16LF1519-E/PT)
설계 노트
Estimated: Decouple every VDD/VSS pair with a 100 nF ceramic placed within 5 mm of the pin. For battery-powered designs, add a 10 uF bulk capacitor near the MCU to absorb transmit-current transients from a co-located wireless module. The PIC16LF1519-I/PT draws typical sleep current of ~50 nA at 1.8 V with WDT disabled; verify the chosen LDO has quiescent current below 1 uA to preserve battery life.
TQFP-44 has 0.8 mm pitch and requires careful land pattern design per IPC-7351. Place the ICSP pins (RB6/RB7) on accessible board-edge or test-pad locations to enable in-circuit debugging without removing the MCU. Keep analog traces (PORTA/PORTE) short and isolated from switching nodes; use a ground pour under the MCU and a single-point analog/digital ground connection near the MCU's VSS pin to minimize ADC noise coupling.
Do not exceed 3.6 V on VDD - the LF variant is NOT 5 V tolerant. Always configure the brown-out reset to a threshold below the minimum operating VDD to prevent code execution at low voltage. When migrating firmware from PIC16F877 to PIC16LF1519, verify peripheral register maps because the enhanced mid-range core uses different SFR addresses than legacy parts. The MSSP peripheral requires configuration of both control registers before SPI or I2C transactions.
For designs using the 10-bit ADC at high source impedances (>10 kohm), add an external buffer op-amp (such as MCP6001) to prevent ADC sampling-capacitor charge sharing from degrading accuracy. Use the dedicated VREF+ pin with a low-noise reference for ratiometric measurements rather than VDD. Keep switching nodes (PWM outputs, relay drivers) physically separated from analog traces, and average 16 or 32 ADC samples in firmware to suppress 50/60 Hz line interference.
규정 준수 정보
RoHS compliant per Microchip product page. Not AEC-Q100 qualified - select PIC16F1519-I/PT or PIC16LF1519-E/PT-E automotive grade for AEC-Q100 designs. Pb-free / halogen-free packaging per Microchip sustainability disclosures.