PIC16LF1707T-I/ML - 8-bit MCU 3.5KB Flash 32MHz QFN-20
부품 번호: PIC16LF1707T-I/ML ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $0.92 | $0.92 |
| 10 | $0.85 | $8.50 |
| 100 | $0.75 | $75.00 |
| 500 | $0.68 | $340.00 |
| 1,000 | $0.6 | $600.00 |
PIC16LF1707T-I/ML 개요
An 8-bit Flash microcontroller is a small, self-contained computer-on-a-chip built around an 8-bit data path, integrating a CPU, non-volatile program memory (Flash), RAM, and a curated set of peripherals (timers, ADC, comparators, communication ports) on a single die. Within the broader semiconductor taxonomy, the PIC16LF1707 sits as: microcontroller -> 8-bit microcontroller -> embedded controller -> integrated circuit. Microcontrollers of this class typically replace discrete logic and analog front-ends in cost-sensitive and space-constrained designs.
The PIC16LF1707 features 256 bytes of SRAM, up to 18 general-purpose I/O pins, an integrated 10-bit ADC with up to 12 channels, two operational amplifiers with rail-to-rail input/output, an 8-bit DAC, two comparators, and peripheral pin select (PPS) for flexible signal routing. XLP technology brings supply current down to a deep-sleep regime suitable for coin-cell applications, while the LF process node (1.8V-3.6V VDD) extends battery life compared to the 5V-capable PIC16F1707 sibling. Peripherals include Master Synchronous Serial Port (MSSP) for SPI/I2C, Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART), and four 10-bit PWM outputs.
Architecturally, the device is built on a 14-bit instruction-word enhanced mid-range core with a hardware stack, single-cycle instruction execution (other than branches), and a configurable oscillator block supporting internal 32 MHz HFINTOSC, 31 kHz LFINTOSC, and external crystal modes. Code is protected by a configurable Flash read protection and a unique 32-bit device ID. The integrated op-amps and DAC allow direct analog signal conditioning on-chip, eliminating many external components in sensor-interface and LED-driving applications.
Typical applications include low-power IoT sensor nodes, wearable fitness and health devices, battery-powered remote controls, LED lighting controllers with analog dimming, small appliance HMI panels, and consumer electronic accessories where a 20-pin footprint and integrated analog reduce BOM cost.
When designing with this device, choose decoupling capacitance per the manufacturer recommended layout (typically 0.1 µF plus 10 µF bulk within 3 mm of the VDD pins), and verify PPS remap constraints before committing to a PCB layout because some peripheral functions must be assigned to specific pins.
This page synthesizes distributor pricing, drop-in same-package alternatives from the same PIC16LF1707 family and across Microchip's wider 8-bit portfolio, and practical design notes not found in the standalone datasheet.
드롭인 대체품: PIC16LF1707T-I/ML — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: PIC16LF1707T-I/ML (동일 폼 팩터 및 풋프린트) — 차이점: Program Memory (Flash), ADC, Operating Temperature, Package, DAC.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
PIC16LF1707-I/ML
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$0.55 / 개
데이터시트 보기 →PIC16F1707T-I/ML
✅ 드롭인✓ 재고 있음
$0.71 / 개
데이터시트 보기 →PIC16LF1704-I/ML
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$0.71 / 개
데이터시트 보기 →PIC16LF15356-I/ML
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$0.96 / 개
데이터시트 보기 →PIC16LF1559T-I/ML
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$1.32 / 개
데이터시트 보기 →PIC16LF1707T-I/ML 최대 정격 & 전기적 특성
| Core Architecture | PIC 8-bit enhanced mid-range |
| Program Memory (Flash) | 3.5 KB (2K x 14) |
| Data RAM | 256 bytes |
| Maximum CPU Speed | 32 MHz (32 MIPS) |
| Supply Voltage (VDD) | 1.8 V to 3.6 V |
| I/O Pins | Up to 18 |
| ADC | 10-bit, up to 12 channels |
| DAC | 8-bit |
| Comparators | 2 |
| Operational Amplifiers | 2 (on-chip, rail-to-rail I/O) |
| PWM Outputs | 4 x 10-bit |
| Communication | 1x MSSP (SPI/I2C), 1x EUSART |
| 동작 온도 | -40C to +85C (Industrial) |
| 패키지 | 20-pin QFN (4x4 mm) with exposed pad |
| 실장 유형 | Surface Mount |
| RoHS 상태 | Compliant |
| Low-Power Technology | XLP (eXtreme Low Power) |
| Internal Oscillator | 32 MHz HFINTOSC + 31 kHz LFINTOSC |
PIC16LF1707T-I/ML 핀 구성
| 핀 1 | RA5 — GPIO / analog input / PWM |
| 핀 2 | RA4 — GPIO / analog input |
| 핀 3 | RA3 — GPIO / MCLR (master clear reset) |
| 핀 4 | RA2 — GPIO / analog input / op-amp output |
| 핀 5 | RA1 — GPIO / analog input / op-amp inverting input |
| 핀 6 | RA0 — GPIO / analog input / op-amp non-inverting input |
| 핀 7 | VSS — Ground reference |
| 핀 8 | RA7 — GPIO / analog input / DAC output |
| 핀 9 | RA6 — GPIO / analog input / comparator output |
| 핀 10 | RC0 — GPIO / PWM / SPI SCK |
| 핀 11 | RC1 — GPIO / PWM / SPI SDI |
| 핀 12 | RC2 — GPIO / PWM / SPI SDO |
| 핀 13 | RC3 — GPIO / PWM / SPI SS |
| 핀 14 | RC4 — GPIO / I2C SDA / EUSART TX |
| 핀 15 | RC5 — GPIO / I2C SCL / EUSART RX |
| 핀 16 | RC6 — GPIO / EUSART TX / PWM |
| 핀 17 | RC7 — GPIO / EUSART RX / PWM |
| 핀 18 | VSS — Ground reference (secondary) |
| 핀 19 | VDD — Positive supply voltage 1.8V-3.6V |
| 핀 20 | VDD — Positive supply voltage (secondary) |
일반적인 애플리케이션
PIC16LF1707T-I/ML 적합 용도: 6 애플리케이션s: Battery-Powered IoT Sensor Nodes, Wearable Fitness and Health Devices, Battery-Powered Remote Controls, LED Lighting Controllers with Analog Dimming, Small Appliance HMI Panels, Consumer Electronic Accessories.
Battery-Powered IoT Sensor Nodes
The PIC16LF1707T-I/ML's XLP platform delivers sub-microamp deep-sleep current, making it well suited for IoT sensor nodes that wake periodically to sample and transmit data over BLE or sub-GHz radios. Its 1.8 V to 3.6 V VDD range supports direct connection to coin cells or single-cell Li-ion batteries, while the integrated 10-bit ADC with up to 12 channels handles multi-sensor input without external multiplexers.
추천
Wearable Fitness and Health Devices
Wearable fitness bands require long battery life and direct analog signal conditioning from heart-rate, SpO2, and motion sensors. The PIC16LF1707T-I/ML's two on-chip rail-to-rail op-amps condition photodiode signals directly, while the 8-bit DAC sets bias voltages for optical front-ends. The 32 MHz CPU can run RTOS-free main loops fast enough to keep active current low, with XLP sleep between bursts extending coin-cell runtime to weeks.
추천
Battery-Powered Remote Controls
Universal remote controls, key fobs, and small RF transmitter keypads benefit from the PIC16LF1707T-I/ML's LF supply range and XLP sleep. The EUSART enables infrared modulation or sub-GHz link interfacing, while the MSSP drives SPI peripherals or I2C sensors. The 4x4 mm QFN-20 footprint fits inside compact handheld enclosures, and the exposed pad provides thermal dissipation for higher duty-cycle TX bursts without throttling.
추천
LED Lighting Controllers with Analog Dimming
Smart LED drivers and architectural dimmers need analog current control and PWM generation. The PIC16LF1707T-I/ML's four 10-bit PWM channels drive MOSFET gates or LED strings directly, while the on-chip op-amps close current-sense loops without external amplifiers. The 8-bit DAC sets reference levels for tunable-white or RGB color mixing, and XLP sleep during standby lighting maintains energy-star efficiency targets.
추천
Small Appliance HMI Panels
Coffee machines, air purifiers, and countertop appliances integrate capacitive-touch buttons, status LEDs, and small displays. The PIC16LF1707T-I/ML's 18 I/O pins handle mTouch proximity sensing, LED matrix driving, and segment LCD via the integrated 8-bit DAC. The MSSP SPI/I2C ports connect to OLED displays or wireless modules, and the LF supply range permits direct 3.3 V regulator operation from rectified mains.
추천
Consumer Electronic Accessories
Computer peripherals, USB dongles, and gaming accessories need compact, low-cost MCUs with mixed signal capability. The PIC16LF1707T-I/ML's 4x4 mm QFN-20 footprint fits inside USB Type-A housings and connector shells, while its integrated op-amps interface analog sensors (temperature, current, light) without external ICs. XLP technology keeps standby current below USB suspend limits, ensuring compliance with USB 2.0 power management specifications.
추천
추천 제품 요약
엔지니어링 참조 데이터: PIC16LF1707T-I/ML — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | PIC16LF1707-I/ML | PIC16F1707T-I/ML | PIC16LF1704-I/ML | PIC16LF15356-I/ML | PIC16LF1559T-I/ML |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | QFN-20 (4x4 mm) | QFN-20 (4x4 mm) - same | QFN-20 (4x4 mm) - same | QFN-20 (4x4 mm) - same | QFN-20 (4x4 mm) - same | QFN-20 (4x4 mm) - same |
| Process / VDD Range | LF / 1.8V-3.6V | LF / 1.8V-3.6V | F / 1.8V-5.5V | LF / 1.8V-3.6V | LF / 1.8V-3.6V | LF / 1.8V-3.6V |
| Program Flash | 3.5 KB | 3.5 KB | 3.5 KB | 7 KB | 28 KB | 14 KB |
| Data RAM | 256 B | 256 B | 256 B | 512 B | 2048 B | 1024 B |
| On-chip Op-amps | 2 | 2 | 2 | 0 | 0 | 0 |
| ADC Resolution / Channels | 10-bit / 12 ch | 10-bit / 12 ch | 10-bit / 12 ch | 10-bit / 12 ch | 10-bit / 22 ch | 10-bit / 17 ch |
| PWM Channels | 4 x 10-bit | 4 x 10-bit | 4 x 10-bit | 4 x 10-bit | 5 x 10-bit | 4 x 10-bit |
주요 차별점
- Two on-chip op-amps eliminate external analog front-end ICs (vs PIC16LF1704-I/ML)
- LF process node with 1.8 V lower VDD for battery applications (vs PIC16F1707T-I/ML)
- Tape-and-reel shipping packaging for OEM production (vs PIC16LF1707-I/ML)
설계 노트
Estimated: Decouple VDD with a 0.1 µF ceramic capacitor placed within 3 mm of pins 19 and 20, plus a 10 µF bulk capacitor on the same net. For XLP deep-sleep operation below 1 µA, route both VDD pins and both VSS pins to solid copper planes and avoid high-impedance analog traces near the VDD bond wires. The exposed thermal pad (pin 21 in some datasheet conventions) must be soldered to a grounded copper island for thermal dissipation and electrical reference.
The QFN-20 (4x4 mm) land pattern requires a center pad of approximately 2.5x2.5 mm with via array stitching to the ground plane for thermal conduction. Stencil aperture should be split into four quadrants (or follow Microchip IPC-7351 compliant QFN recommendations) to prevent solder voiding. Recommended PCB land footprint and via pattern are documented in Microchip application note AN279 and the PIC16LF1707 datasheet's PCB layout section.
When migrating firmware between PIC16LF1707T-I/ML and the F-process PIC16F1707T-I/ML, verify VDD upper limit (3.6 V vs 5.5 V) and analog voltage reference scaling. The MSSP module's I2C fast-mode (400 kHz) and high-speed mode (3.4 MHz) require specific SDA/SCL slew-rate configuration via the SSP1STAT and SSP1CON registers. Avoid leaving unused pins floating - configure them as outputs low or enable the weak pull-ups via WPUA/WPUC registers to minimize sleep current leakage.
규정 준수 정보
RoHS and REACH compliance per Microchip product page. Industrial temperature grade -40C to +85C only; not AEC-Q100 qualified for automotive. Halogen-free per Microchip green packaging standards.
