PIC16LF873A-I/ML - 8-Bit 10MHz 7KB Flash MCU 28-QFN | Microchip
부품 번호: PIC16LF873A-I/ML ✗ 단종| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $6.45 | $6.45 |
| 10 | $5.83 | $58.30 |
| 100 | $5.18 | $518.00 |
| 500 | $4.66 | $2,330.00 |
| 1,000 | $4.21 | $4,210.00 |
PIC16LF873A-I/ML 개요
A microcontroller (MCU) is a single-chip computer that integrates a CPU, RAM, non-volatile program memory, peripheral modules, and I/O on one die; in the PIC16F family the RISC Harvard architecture with 35 single-word instructions simplifies firmware development and yields deterministic interrupt response. The PIC16LF873A sits in the hierarchy: 8-bit microcontroller -> PIC16 mid-range family -> nanoWatt power-managed MCUs -> embedded controllers -> integrated circuits.
Key features include In-Circuit Serial Programming (ICSP) for field upgrades, a wide operating voltage window (2.0V-5.5V) that supports both 3.3V and 5V designs, programmable code protection, and low-power SLEEP/idle modes with <1 uA typical current. The 10-bit ADC with five input channels enables direct sensor interfacing, while the USART and MSSP provide asynchronous serial and synchronous SPI/I2C master/slave communications. Two CCP modules deliver PWM, capture, and compare functions for motor and lighting control.
The Harvard-style architecture separates program and data buses, enabling simultaneous fetch and access. With 4K 14-bit instruction words, the device supports high-level C compilation via MPLAB XC8 while remaining efficient for hand-written assembly. The exposed thermal pad on the QFN package provides low thermal resistance for industrial environments.
Typical applications include industrial sensor signal conditioning with ADC input, 3.3V-5V bridge power conversion, low-power wireless sensor nodes, HVAC fan motor PWM control, and battery-powered portable instrumentation where the wide voltage range and nanoWatt sleep currents extend operating life.
When designing with the PIC16LF873A-I/ML, place 100 nF decoupling capacitors within 3 mm of each VDD pin and tie the exposed pad (EP) to a clean ground pour. For ADC accuracy, add an external voltage reference and avoid routing digital traces under analog traces on inner layers.
This page synthesizes distributor pricing, drop-in alternatives from the same PIC16 family, and practical design notes not aggregated on any single manufacturer or distributor page.
드롭인 대체품: PIC16LF873A-I/ML — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: PIC16LF873A-I/ML (동일 폼 팩터 및 풋프린트) — 차이점: Package, Timers, ADC, Core Architecture, Operating Temperature Range.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
PIC16LF873A-I/SP
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$5.78 / 개
데이터시트 보기 →PIC16LF873A-I/SS
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$3.05 / 개
데이터시트 보기 →PIC16F873A-I/ML
✅ 드롭인✓ 재고 있음
$2.32 / 개
데이터시트 보기 →PIC16LF876A-I/ML
✅ 드롭인✓ 재고 있음
$3.85 / 개
데이터시트 보기 →PIC16LF77-I/ML
✅ 드롭인✓ 재고 있음
$5.1 / 개
데이터시트 보기 →PIC16LF76-I/ML
✅ 드롭인✓ 재고 있음
$4.2 / 개
데이터시트 보기 →PIC16LF73-I/ML
✅ 드롭인✓ 재고 있음
$4.38 / 개
데이터시트 보기 →PIC16LF873A-I/ML 최대 정격 & 전기적 특성
| Core Processor | PIC |
| Core Size | 8-bit |
| Instruction Set | PIC16 (RISC, 35 instructions) |
| Program Memory Size | 7KB (4K x 14 words) FLASH |
| RAM Size | 192 bytes |
| EEPROM Size | 128 bytes |
| Operating Frequency | 10 MHz (200 ns instruction cycle) |
| Supply Voltage Range | 2.0 V to 5.5 V |
| I/O Pins | 22 |
| ADC | 10-bit, 5 channels |
| Communication Interfaces | USART, MSSP (SPI / I2C) |
| Timers | 1 x 8-bit, 2 x 16-bit (with CCP) |
| 동작 온도 | -40 C to +85 C (Industrial) |
| 패키지 | 28-QFN (6x6 mm) with EP |
| 실장 유형 | Surface Mount |
| MSL 레벨 | 3 (168 hours) |
| Oscillator Type | External |
| Program Memory Type | FLASH (self-programmable, ICSP) |
| RoHS 상태 | Compliant |
| Lead-Free / Halogen-Free | Lead-Free (per Microchip) |
PIC16LF873A-I/ML 핀 구성
| 핀 1 | MCLR/VPP/THV — Master clear (active-low reset) / programming voltage / threshold reference |
| 핀 2 | RA0/AN0 — PORTA bit 0 / analog input channel 0 |
| 핀 3 | RA1/AN1 — PORTA bit 1 / analog input channel 1 |
| 핀 4 | RA2/AN2/VREF- — PORTA bit 2 / analog input 2 / ADC VREF- |
| 핀 5 | RA3/AN3/VREF+ — PORTA bit 3 / analog input 3 / ADC VREF+ |
| 핀 6 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input (open-drain) |
| 핀 7 | RA5/AN4/SS — PORTA bit 5 / analog input 4 / SPI slave select |
| 핀 8 | VSS — Ground reference |
| 핀 9 | OSC1/CLKI — Crystal oscillator input / external clock input |
| 핀 10 | OSC2/CLKO — Crystal oscillator output / clock output |
| 핀 11 | RC0/T1OSO/T1CKI — PORTC bit 0 / Timer1 oscillator output / Timer1 clock input |
| 핀 12 | RC1/T1OSI/CCP2 — PORTC bit 1 / Timer1 oscillator input / CCP2 |
| 핀 13 | RC2/CCP1 — PORTC bit 2 / CCP1 (PWM/Capture/Compare) |
| 핀 14 | RC3/SCK/SCL — PORTC bit 3 / SPI clock / I2C clock |
| 핀 15 | RC4/SDI/SDA — PORTC bit 4 / SPI data in / I2C data |
| 핀 16 | RC5/SDO — PORTC bit 5 / SPI data out |
| 핀 17 | RC6/TX/CK — PORTC bit 6 / USART TX / USART clock |
| 핀 18 | RC7/RX/DT — PORTC bit 7 / USART RX / USART data |
| 핀 19 | VSS — Ground reference |
| 핀 20 | VDD — Positive supply voltage |
| 핀 21 | RB0/INT — PORTB bit 0 / external interrupt |
| 핀 22 | RB1 — PORTB bit 1 |
| 핀 23 | RB2 — PORTB bit 2 |
| 핀 24 | RB3/PGM — PORTB bit 3 / low-voltage programming |
| 핀 25 | RB4 — PORTB bit 4 |
| 핀 26 | RB5 — PORTB bit 5 |
| 핀 27 | RB6/PGC — PORTB bit 6 / ICSP clock |
| 핀 28 | RB7/PGD — PORTB bit 7 / ICSP data |
일반적인 애플리케이션
PIC16LF873A-I/ML 적합 용도: 7 애플리케이션s: Industrial Sensor Signal Conditioning, Battery-Powered Wireless Sensor Node, HVAC Fan Motor PWM Control, 3.3V to 5V Bridge / Protocol Converter, Portable Handheld Instrumentation, LED Lighting Control Systems, Educational MCU Training Boards.
Industrial Sensor Signal Conditioning
The PIC16LF873A-I/ML suits industrial sensor signal conditioning boards that digitize 0-5V transducer outputs. Its 10-bit ADC with 5 input channels provides 4.88 mV resolution at 5V VDD, sufficient for thermocouple pre-amplifier output, strain-gauge bridge amplification, or 4-20 mA loop sense resistor monitoring. The wide 2.0V-5.5V supply range accepts both 24V industrial rails stepped down to 5V and battery-derived 3.3V supplies. The USART streams digitized values to a host PLC or displays results on a local LCD driven by GPIO bit-banging. Industrial -40C to +85C rating covers factory-floor enclosures. The QFN package's small 6x6 mm footprint fits inside sensor heads or DIN-rail transmitter housings.
추천
Battery-Powered Wireless Sensor Node
The PIC16LF873A-I/ML is well suited to battery-powered wireless sensor nodes where sleep current dominates battery life. nanoWatt SLEEP mode draws less than 1 uA at 3V, allowing a 2400 mAh AA pack to support years of operation if the MCU wakes only briefly to take an ADC reading and transmit. The 2.0V-5.5V range accepts the voltage droop of alkaline or lithium chemistries without brown-out reset. The MSSP SPI port connects directly to sub-GHz transceiver ICs, and 22 GPIO pins accommodate multiple sensor channels and indicator LEDs. The 28-QFN's exposed pad ties to ground for thermal stability during RF transmission bursts. PIC firmware leverages ICSP for over-the-air bootloader updates.
추천
HVAC Fan Motor PWM Control
The PIC16LF873A-I/ML drives HVAC fan motors through its two 16-bit Capture/Compare/PWM (CCP) modules that generate complementary or variable-frequency PWM outputs at up to 10-bit resolution. Closed-loop speed control reads a tachometer or back-EMF signal via the 10-bit ADC and adjusts duty cycle accordingly. The USART connects to a central HVAC controller over RS-485 through an external transceiver. Industrial -40C to +85C operation covers plenum-mounted enclosures. The MSSP I2C bus reads temperature and humidity sensors for variable-air-volume (VAV) logic. Code protection prevents firmware cloning by aftermarket competitors.
추천
3.3V to 5V Bridge / Protocol Converter
The PIC16LF873A-I/ML acts as a level-translating bridge between 3.3V UART peripherals and legacy 5V RS-232 equipment. With VDD at 3.3V, GPIO pins meet LVCMOS thresholds; with VDD at 5V, the same firmware drives TTL-level serial lines. The wide operating range allows a single PCB design to strap-select 3.3V or 5V via a regulator jumper. The MSSP handles SPI-to-UART or I2C-to-UART protocol conversion for system integrators migrating older 5V subsystems to 3.3V SoCs. The 7KB FLASH holds table-driven protocol conversion firmware; 192B RAM buffers incoming packets.
추천
Portable Handheld Instrumentation
The PIC16LF873A-I/ML forms the core of portable handheld instruments such as digital multimeters, clamp meters, or environmental meters where size, weight, and battery life matter. Its 28-QFN 6x6 mm footprint leaves room for the LCD driver, op-amp front end, and AA-cell holders in a compact enclosure. The 10-bit ADC digitizes voltage, current, and temperature sensors with adequate resolution for consumer-grade accuracy. nanoWatt SLEEP between measurements extends battery life to hundreds of hours. ICSP allows field firmware updates as new measurement modes are added.
추천
LED Lighting Control Systems
The PIC16LF873A-I/ML manages addressable RGB LED strips and DMX-512 lighting controllers. Its 22 GPIO pins directly drive low-current LED driver enable lines, while the two CCP modules generate high-resolution PWM dimming signals up to 10 kHz without flicker. The USART receives DMX-512 frames at 250 kbaud through an external RS-485 transceiver. The 10-bit ADC reads ambient light sensors for daylight harvesting and adjusts output brightness accordingly. nanoWatt SLEEP during off-hours minimizes standby power in architectural lighting installations.
추천
Educational MCU Training Boards
The PIC16LF873A-I/ML is widely adopted in university microcontroller courses and embedded-systems labs because of its simple 35-instruction PIC16 architecture, comprehensive Microchip documentation, and free MPLAB X toolchain. The 28-QFN package suits modern SMD training boards while DIP adapters allow breadboard experimentation. Students program the device with PICkit 4 or MPLAB Snap debuggers, learning GPIO, ADC, USART, I2C, SPI, and timer peripherals. Migrating later to PIC18 or dsPIC33 series builds on the same PIC assembly foundation.
추천
추천 제품 요약
엔지니어링 참조 데이터: PIC16LF873A-I/ML — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | PIC16F873A-I/ML | PIC16LF876A-I/ML | PIC16LF77-I/ML | PIC16LF76-I/ML | PIC16LF73-I/ML |
|---|---|---|---|---|---|---|
| Package | 28-QFN (6x6) | 28-QFN (6x6) | 28-QFN (6x6) | 28-QFN (6x6) | 28-QFN (6x6) | 28-QFN (6x6) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Program FLASH | 7KB (4K x 14) | 7KB (4K x 14) | 14KB (8K x 14) | 14KB (8K x 14) | 14KB (8K x 14) | 7KB (4K x 14) |
| RAM | 192 bytes | 192 bytes | 368 bytes | 368 bytes | 368 bytes | 192 bytes |
| I/O Pins | 22 | 22 | 22 | 22 | 22 | 22 |
| ADC | 10-bit, 5 ch | 10-bit, 5 ch | 10-bit, 5 ch | 10-bit, 5 ch | 10-bit, 5 ch | 12-bit, 5 ch |
| Operating Voltage | 2.0V - 5.5V | 2.0V - 5.5V | 2.0V - 5.5V | 2.0V - 5.5V | 2.0V - 5.5V | 2.0V - 5.5V |
| MSSP / USART | MSSP + USART | MSSP + USART | MSSP + USART | MSSP + USART | MSSP + USART | MSSP only |
주요 차별점
- 5-channel 10-bit ADC integrated (vs PIC16LF73-I/ML)
- USART plus MSSP dual communication (vs PIC16LF73-I/ML)
- Lower memory ceiling vs. F876A (vs PIC16LF876A-I/ML)
- Wide operating voltage 2.0V-5.5V (vs PIC16F873A-I/ML)
설계 노트
The PIC16LF873A-I/ML nanoWatt SLEEP draws less than 1 uA at 3V, but total quiescent current of the system board is dominated by external components. Choose a low-Iq LDO such as MCP1700 (1.6 uA quiescent) to preserve battery life. Bulk-decouple VDD with 100 nF X7R placed within 3 mm of the supply pin; add 10 uF tantalum or polymer bulk capacitance if the MCU drives power-hungry peripherals from the same rail.
The 28-QFN package's exposed thermal pad (EP) provides the primary heat-dissipation path. Solder the EP to a continuous ground pour of at least 50 mm^2 to keep junction temperature within ratings. The package's theta_JA of approximately 30 C/W on a 4-layer JEDEC test board drops to over 80 C/W on a small 2-layer board with a poor thermal via pattern; add thermal vias to the EP for high-current applications driving multiple GPIO outputs simultaneously.
Route the analog inputs AN0-AN4 away from digital switching signals; the 10-bit ADC samples the analog voltage at the S/H capacitor, and noise coupling from clock or PWM traces introduces conversion errors. Use a separate analog ground island if possible, joined to digital ground at a single point near the MCU. For 5V ADC operation above 4.096V, provide an external MCP1541 4.096V reference to avoid ADC ratiometric ambiguity with VDD noise.
Configuration words are read at every reset - never leave them at the default erased state (all 1s). Always program CONFIG1 through CONFIG4 with proper oscillator, watchdog, brown-out, and code-protection settings before code can run reliably. Missing configuration word settings is the most common reason first-time PIC16 designs fail to start. Use MPLAB X's configuration bit viewer to set WDT_OFF, BOREN_SOFT, and IESO_OFF for typical industrial designs.
The ICSP clock (PGC, RB6) and data (PGD, RB7) pins must be accessible in the final assembly for field firmware updates. Do not populate resistors or buffers in series with these pins unless they can be bypassed for programming. The MCLR pin should be pulled up to VDD with a 10 kohm resistor and decoupled with a 100 nF capacitor; missing MCLR capacitance causes spurious resets in noisy industrial environments.
규정 준수 정보
RoHS compliant per Microchip product page; lead-free reflow-compatible per JEDEC J-STD-020; MSL 3 (168-hour floor life). NRND status - check Microchip PCN for automotive suitability.
