PIC17C42A-16I/P - 8-Bit 16MHz OTP MCU, 40-PDIP | Microchip
부품 번호: PIC17C42A-16I/P ⚠ 최종 구매| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $6.5 | $6.50 |
| 10 | $5.85 | $58.50 |
| 100 | $5.2 | $520.00 |
| 500 | $4.65 | $2,325.00 |
| 1,000 | $4.1 | $4,100.00 |
PIC17C42A-16I/P 개요
Background: An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory, RAM, peripherals, and I/O. PIC17C series microcontrollers use a RISC-based Harvard architecture with 58 single-word instructions, most executing in a single instruction cycle (121 ns at 16 MHz oscillator input). The 17C family sits above the baseline PIC16 in Microchip's portfolio, adding hardware multipliers, additional timers, USART, PWM, and capture modules for real-time control applications.
Key features of the PIC17C42A-16I/P include 8.25 MIPS throughput, an external oscillator interface, three hardware timers, two capture inputs, two PWM outputs, a hardware USART, an 8x8 hardware multiplier, and a 16-level hardware stack. The OTP (One-Time-Programmable) memory enables pre-programmed code for prototyping and low-to-medium volume production runs. The 'I' suffix denotes industrial temperature grade (-40C to +85C).
Architecturally, the PIC17C42A uses a 16-bit-wide instruction word with an 8-bit data path, providing 2K instruction words and 232 bytes of register-mapped RAM. Compared to PIC16C devices, the 17C core widens the program bus, adds indexed addressing with two address pointers, and integrates a hardware multiply unit.
Typical applications include industrial control loops, motor drives, smart sensors, automotive subsystems, security panels, and embedded data-acquisition front-ends that need deterministic timing and a small footprint.
Design consideration: When replacing or sourcing this part, note that Microchip has marked the PIC17C42A as legacy. For new designs, Microchip recommends the PIC18F family as a modern flash-based migration path. Designers should verify oscillator input drive strength and use a 100 nF decoupling capacitor on VDD placed within 5 mm of the package pins.
This page synthesizes distributor pricing, drop-in PDIP alternatives within the PIC17C family, and practical design notes not found in the manufacturer datasheet alone.
드롭인 대체품: PIC17C42A-16I/P — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: PIC17C42A-16I/P (동일 폼 팩터 및 풋프린트) — 차이점: Operating Temperature, Package, Mounting Type, Program Memory Type, Hardware Multiplier.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
PIC17C42A-16/P
✅ 드롭인✓ 재고 있음
$7.45 / 개
데이터시트 보기 →PIC17C42A-16E/P
✅ 드롭인✓ 재고 있음
$5.85 / 개
데이터시트 보기 →PIC17C43-16I/P
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC17C42A-16I/L
✅ 드롭인✓ 재고 있음
$9.95 / 개
데이터시트 보기 →PIC17C42A-16I/PQ
✅ 드롭인✓ 재고 있음
$8.95 / 개
데이터시트 보기 →PIC17C42A-16I/P 최대 정격 & 전기적 특성
| Core Architecture | 8-bit PIC17C RISC |
| Program Memory Type | OTP EPROM |
| Program Memory Size | 4 KB (2K x 16) |
| RAM Size | 232 x 8 bytes |
| Maximum CPU Frequency | 16 MHz |
| Instruction Cycle Time | 121 ns (single cycle) |
| Throughput | 8.25 MIPS |
| Number of I/O Pins | 33 |
| Number of Instructions | 58 single-word |
| Hardware Multiplier | 8 x 8 (single-cycle) |
| Timers | 3 |
| Capture Inputs | 2 |
| PWM Outputs | 2 |
| Communication | USART (1x) |
| Oscillator Type | External |
| 동작 온도 | -40C to +85C (industrial grade) |
| 패키지 | 40-PDIP (through-hole) |
| 실장 유형 | Through-Hole |
PIC17C42A-16I/P 핀 구성
| 핀 1 | RA0/AN0 — PORTA bit 0 / analog input 0 |
| 핀 2 | RA1/AN1 — PORTA bit 1 / analog input 1 |
| 핀 3 | RA2/AN2 — PORTA bit 2 / analog input 2 |
| 핀 4 | RA3/AN3 — PORTA bit 3 / analog input 3 |
| 핀 5 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| 핀 6 | RA5/SS — PORTA bit 5 / SPI slave select |
| 핀 7 | RA6/CLKOUT — PORTA bit 6 / clock output |
| 핀 8 | RA7 — PORTA bit 7 |
| 핀 9 | OSC1 — External oscillator input |
| 핀 10 | OSC2 — Oscillator output / crystal connection |
| 핀 11 | MCLR — Master clear reset (active low) |
| 핀 12 | VSS — Ground reference |
| 핀 13 | VDD — Positive supply voltage |
| 핀 14 | RB0/INT — PORTB bit 0 / external interrupt |
| 핀 15 | RB1 — PORTB bit 1 |
| 핀 16 | RB2 — PORTB bit 2 |
| 핀 17 | RB3 — PORTB bit 3 |
| 핀 18 | RB4 — PORTB bit 4 |
| 핀 19 | RB5 — PORTB bit 5 |
| 핀 20 | RB6 — PORTB bit 6 |
| 핀 21 | RB7 — PORTB bit 7 |
| 핀 22 | RC0 — PORTC bit 0 |
| 핀 23 | RC1 — PORTC bit 1 |
| 핀 24 | RC2 — PORTC bit 2 |
| 핀 25 | RC3 — PORTC bit 3 |
| 핀 26 | RC4 — PORTC bit 4 |
| 핀 27 | RC5 — PORTC bit 5 |
| 핀 28 | RC6 — PORTC bit 6 |
| 핀 29 | RC7 — PORTC bit 7 |
| 핀 30 | VSS — Ground reference |
| 핀 31 | VDD — Positive supply voltage |
| 핀 32 | RD0 — PORTD bit 0 |
| 핀 33 | RD1 — PORTD bit 1 |
| 핀 34 | RD2 — PORTD bit 2 |
| 핀 35 | RD3 — PORTD bit 3 |
| 핀 36 | RD4 — PORTD bit 4 |
| 핀 37 | RD5 — PORTD bit 5 |
| 핀 38 | RD6 — PORTD bit 6 |
| 핀 39 | RD7 — PORTD bit 7 |
| 핀 40 | RE0 — PORTE bit 0 |
일반적인 애플리케이션
PIC17C42A-16I/P 적합 용도: 6 애플리케이션s: Industrial Motor Control, Smart Sensor / Data Acquisition Front-End, Security and Alarm Panels, Automotive Body and Accessory Modules, Embedded Real-Time Control Loops, Legacy Embedded System Maintenance and Repair.
Industrial Motor Control
The PIC17C42A-16I/P fits industrial motor control because its 8.25 MIPS throughput delivers deterministic 121 ns single-cycle instruction execution, two PWM outputs drive H-bridge or three-phase gate signals, and two capture inputs read quadrature encoder feedback at high update rates. The hardware 8x8 multiplier closes PI and field-oriented control loops without CPU stalls, and the USART provides a robust isolated RS-485/Modbus link to a host controller. Placed on a 40-PDIP through-hole PCB, the industrial -40C to +85C temperature grade survives cabinet environments, while 33 I/O pins accept limit-switch, thermistor, and brake-resistor signals directly.
추천
Smart Sensor / Data Acquisition Front-End
The PIC17C42A-16I/P is well matched to a smart-sensor data-acquisition front-end because 33 I/O pins connect to multiple analog and digital sensor channels, the USART streams digitized samples to a host, and three timers pace sampling-rate-sensitive inputs without CPU polling overhead. The 232-byte RAM is sufficient for circular sample buffers in sensor-protocol gateways, and the 4 KB OTP holds protocol stacks for sensor-bus standards. Drawing typically under 25 mA active, the part fits remote or solar-powered installations where the industrial temperature rating ensures operation from cold storage to hot industrial cabinets.
추천
Security and Alarm Panels
The PIC17C42A-16I/P suits security and alarm panels because 33 I/O lines interface directly to PIR sensors, magnetic reed switches, keypad matrices, sirens, and relay outputs without external mux logic, and the OTP memory protects proprietary zone-decision firmware from reverse engineering. Two PWM outputs can drive piezo sirens with programmable tone patterns, while two capture inputs time-stamp door-chime events for the event log. The USART talks to a digital dialer or central-station modem, and the -40C to +85C industrial grade covers unheated garages and outdoor enclosures.
추천
Automotive Body and Accessory Modules
The PIC17C42A-16I/P powers automotive body-electronic modules because its hardware USART interfaces with LIN bus transceivers, two PWM outputs dim instrument-panel backlights and drive small DC loads, and 33 I/O pins handle window, mirror, seat, and wiper switches. The 8.25 MIPS throughput runs switch-debounce, multiplexed indicator logic, and basic diagnostics within tight scheduling windows. Designers should note that the part is not AEC-Q100 qualified; for under-hood or ABS modules, choose AEC-Q100-qualified PIC18 alternatives, but for cabin-mounted accessories the PIC17C42A-16I/P is adequate.
추천
Embedded Real-Time Control Loops
The PIC17C42A-16I/P is ideal for embedded real-time control loops because every instruction except branches executes in a single 121 ns cycle at 16 MHz, and three hardware timers (Timer0, Timer1, Timer2) generate deterministic interrupts for fixed-rate control periods. The 8x8 hardware multiplier accelerates PI and PID math, while two PWM outputs drive actuators and two capture inputs read rotary-encoder feedback. With 232 bytes of RAM and 33 I/O pins, the MCU fits mid-sized loop controllers such as HVAC damper actuators, pump speed controllers, and small VFD reference boards without external logic.
추천
Legacy Embedded System Maintenance and Repair
The PIC17C42A-16I/P remains in demand for legacy embedded system maintenance because Microchip factory stock is depleted and many installed industrial controllers, security panels, and laboratory instruments depend on this exact die revision. Service engineers can order direct drop-in replacements on the same 40-PDIP footprint, restoring production lines and lab equipment without board redesign. The OTP memory matches the original firmware image exactly, while the industrial -40C to +85C rating keeps replacement units aligned with the original bill of materials.
추천
추천 제품 요약
엔지니어링 참조 데이터: PIC17C42A-16I/P — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | PIC17C42A-16/P | PIC17C42A-16E/P | PIC17C43-16I/P | PIC17C42A-16I/L | PIC17C42A-16I/PQ |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 40-PDIP (through-hole) | 40-PDIP - same | 40-PDIP - same | 40-PDIP - same | 40-pin CERDIP (L) - same pin count, different body | 44-PQFP (Q) - NOT same footprint |
| Program Memory | 4 KB (2K x 16) OTP | 4 KB OTP | 4 KB OTP | 8 KB (4K x 16) OTP | 4 KB EPROM (UV-eraseable) | 4 KB OTP |
| Maximum Frequency | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 16 MHz |
| RAM Size | 232 bytes | 232 bytes | 232 bytes | 454 bytes | 232 bytes | 232 bytes |
| Temperature Grade | Industrial (-40C to +85C) | Commercial (0C to +70C) | Extended grade variant | Industrial (-40C to +85C) | Industrial (-40C to +85C) | Industrial (-40C to +85C) |
| Memory Type | OTP (one-time programmable) | OTP | OTP | OTP | Windowed EPROM (UV-eraseable for prototype use) | OTP |
| Pin Count | 40 | 40 | 40 | 40 | 40 | 44 (PQFP, not pin-compatible) |
| Lifecycle Status | Last-time-buy (legacy) | Last-time-buy | Last-time-buy | Last-time-buy | Last-time-buy | Last-time-buy |
주요 차별점
- Pin-compatible 8 KB code upgrade on the same 40-PDIP footprint (vs PIC17C42A-16/P)
- UV-eraseable windowed package for prototype development (vs PIC17C42A-16I/P (OTP))
- Microchip-recommended flash migration for new designs (vs PIC18F4220)
설계 노트
Place a 100 nF decoupling capacitor within 5 mm of each VDD/VDDx pin pair on the PIC17C42A-16I/P, and add a bulk 10 uF tantalum or low-ESR aluminum electrolytic capacitor on the board-side supply. The device draws approximately 25 mA active at 16 MHz; ensure the upstream regulator provides at least 50 mA headroom and tolerates 50 mV or less of supply droop during PWM transitions.
The PIC17C42A-16I/P is OTP (one-time programmable) and cannot be reprogrammed. Confirm your firmware is fully debugged on a windowed PIC17C42A-16I/L before committing production units, or stock a re-spin allowance for any engineering change. Also note that migrating from PIC16C to PIC17C requires attention to interrupt vector count and configuration word layout - they are NOT the same family.
For the 40-pin PDIP layout, keep analog inputs (RA0-RA5) physically separated from PWM outputs and oscillator traces to minimize digital coupling into ADC readings. Route the external oscillator traces short, symmetric, and guarded by a ground pour to suppress EMI; long oscillator traces can inject phase noise into PWM edge timing. Note that the migration path PIC18F4220 is NOT pin-compatible, so allocate board space for a potential redesign.
규정 준수 정보
RoHS, REACH, lead-free, halogen-free, and conflict-minerals status are not stated in the verified web data and must be confirmed against the supplier's certificate of compliance for the specific lot. The part is not AEC-Q100 qualified; do not use for automotive safety-critical applications.
