PIC17C44-25/PT - 8-Bit CMOS OTP MCU 16KB 25MHz TQFP-44 | Microchip
부품 번호: PIC17C44-25/PT ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $12.07 | $12.07 |
| 10 | $11.5 | $115.00 |
| 100 | $10.2 | $1,020.00 |
| 500 | $8.95 | $4,475.00 |
| 1,000 | $7.8 | $7,800.00 |
PIC17C44-25/PT 개요
A microcontroller (MCU) is a single-chip computer that contains a processor core, memory, and programmable I/O peripherals. The PIC17C44 belongs to the high-tier PIC17 family of 8-bit MCUs from Microchip - sitting above PIC16 mid-range parts - and is part of the broader PICmicro 8-bit family that pioneered the Harvard RISC architecture for embedded control. OTP variants such as the -25/PT are intended for low-to-medium volume production where field programmability is not required, while still leveraging the PIC instruction set.
Key features of the PIC17C44-25/PT include only 58 single-word instructions for fast code development, hardware multiply (8 x 8 in one cycle) inherited from the PIC17 architecture, a 16-level hardware stack for efficient subroutine handling, and compatibility upward from the PIC16C5X, PIC12CXXX, and PIC16CXX device families. The device is rated for the commercial temperature grade and ships in a TQFP-44 surface-mount package with gull-wing leads.
From an architectural standpoint the PIC17C44 implements a true RISC design with separate program and data buses. Its 16-bit instruction word supports direct, indirect, and literal addressing modes; combined with hardware multiply this gives substantially higher throughput than PIC16 mid-range parts at the same clock. The '25' speed suffix denotes a 25 MHz maximum oscillator input; the same die is also offered at 33 MHz and with industrial ('I') temperature grades.
Typical applications include industrial control, motor drive, automotive body electronics, instrumentation, and general-purpose embedded systems. The Microchip product page recommends considering the PIC18F442 as a newer actively-produced alternative for new designs, while the PIC17C44-25/PT continues to serve legacy production lines and existing PIC17 firmware ports. Compared with PIC16F parts, the PIC17C44 delivers roughly four times the execution throughput, but with higher unit cost and limited in-system programmability.
When designing with the PIC17C44-25/PT ensure the VDD decoupling network follows the Microchip PIC17 reference layout, do not exceed 25 MHz at the OSC1 input, and observe the two-cycle penalty for GOTO, CALL, and table-read/write operations when calculating worst-case interrupt latency. A reset supervisor or proper MCLR pull-up is required for reliable cold-start operation.
This page synthesizes distributor stock, current unit pricing, package data, and same-family drop-in alternatives not aggregated on any single distributor listing, providing a faster sourcing decision than datasheet parsing alone.
드롭인 대체품: PIC17C44-25/PT — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: PIC17C44-25/PT (동일 폼 팩터 및 풋프린트) — 차이점: Core Architecture, Instruction Cycle Time, Program Memory Size, Program Memory Type, Package.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
PIC17C44-25I/PT
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC17C44-16I/PT
✅ 드롭인✓ 재고 있음
$4.65 / 개
데이터시트 보기 →PIC17C44T-25/PT
✅ 드롭인✓ 재고 있음
$5.75 / 개
데이터시트 보기 →PIC17C44-33/PT
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
PIC17C44-25I/L
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC17C44-16/PT
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
PIC17C44-25/PT 최대 정격 & 전기적 특성
| Product Type | 8-bit Microcontroller (MCU) |
| Family | PIC17Cxx |
| Core Architecture | 8-bit Harvard RISC |
| Program Memory Type | OTP EPROM |
| Program Memory Size | 16 KB (8K x 16) |
| 최대 클록 주파수 | 25 MHz |
| Instruction Cycle Time | 121 ns (single-cycle except branches) |
| Throughput | 8.25 MIPS |
| Instruction Set Size | 58 single-word instructions |
| Supply Voltage (VDD) | 5 V nominal (commercial grade) |
| Operating Temperature Grade | Commercial |
| Package Type | TQFP-44 (PT) - 10 x 10 mm |
| 핀 수 | 44 |
| 실장 유형 | Surface Mount (gull-wing) |
| Upward Compatibility | PIC16C5X, PIC12CXXX, PIC16CXX |
PIC17C44-25/PT 핀 구성
| 핀 1 | OSC1/CLKIN — Oscillator crystal input or external clock input |
| 핀 2 | RA0 — PORTA bit 0 (digital I/O) |
| 핀 3 | RA1 — PORTA bit 1 (digital I/O) |
| 핀 4 | RA2 — PORTA bit 2 (digital I/O) |
| 핀 5 | RA3 — PORTA bit 3 (digital I/O) |
| 핀 6 | RA4 — PORTA bit 4 (digital I/O / T0CKI) |
| 핀 7 | RA5 — PORTA bit 5 (digital I/O) |
| 핀 8 | RB0/INT — PORTB bit 0 / external interrupt |
| 핀 9 | RB1 — PORTB bit 1 (digital I/O) |
| 핀 10 | RB2 — PORTB bit 2 (digital I/O) |
| 핀 11 | RB3 — PORTB bit 3 (digital I/O) |
| 핀 12 | RB4 — PORTB bit 4 (digital I/O) |
| 핀 13 | RB5 — PORTB bit 5 (digital I/O) |
| 핀 14 | RB6 — PORTB bit 6 (digital I/O / PGC) |
| 핀 15 | RB7 — PORTB bit 7 (digital I/O / PGD) |
| 핀 16 | RC0 — PORTC bit 0 (digital I/O / T1OSO) |
| 핀 17 | RC1 — PORTC bit 1 (digital I/O / T1OSI) |
| 핀 18 | RC2 — PORTC bit 2 (digital I/O / CCP1) |
| 핀 19 | RC3 — PORTC bit 3 (digital I/O / SCL) |
| 핀 20 | RC4 — PORTC bit 4 (digital I/O / SDA) |
| 핀 21 | RC5 — PORTC bit 5 (digital I/O / SDO) |
| 핀 22 | RC6 — PORTC bit 6 (digital I/O / TX) |
| 핀 23 | RC7 — PORTC bit 7 (digital I/O / RX) |
| 핀 24 | RD0 — PORTD bit 0 (digital I/O) |
| 핀 25 | RD1 — PORTD bit 1 (digital I/O) |
| 핀 26 | RD2 — PORTD bit 2 (digital I/O) |
| 핀 27 | RD3 — PORTD bit 3 (digital I/O) |
| 핀 28 | RD4 — PORTD bit 4 (digital I/O) |
| 핀 29 | RD5 — PORTD bit 5 (digital I/O) |
| 핀 30 | RD6 — PORTD bit 6 (digital I/O) |
| 핀 31 | RD7 — PORTD bit 7 (digital I/O) |
| 핀 32 | RE0 — PORTE bit 0 (digital I/O) |
| 핀 33 | RE1 — PORTE bit 1 (digital I/O) |
| 핀 34 | RE2 — PORTE bit 2 (digital I/O) |
| 핀 35 | VSS — Ground reference |
| 핀 36 | VDD — Positive supply (5V) |
| 핀 37 | OSC2/CLKOUT — Oscillator crystal output / clock output |
| 핀 38 | MCLR/VPP — Master clear reset / programming voltage |
| 핀 39 | NC — Not connected (per datasheet) |
| 핀 40 | NC — Not connected (per datasheet) |
| 핀 41 | NC — Not connected (per datasheet) |
| 핀 42 | NC — Not connected (per datasheet) |
| 핀 43 | NC — Not connected (per datasheet) |
| 핀 44 | NC — Not connected (per datasheet) |
일반적인 애플리케이션
PIC17C44-25/PT 적합 용도: 6 애플리케이션s: Industrial Motor Control, Automotive Body Electronics (Legacy), Process Control Instrumentation, Embedded Control Systems (General Purpose), Medical Monitoring Devices (Non-Critical), Consumer Appliance Controllers.
Industrial Motor Control
The PIC17C44-25/PT fits industrial motor control loops because its 8.25 MIPS throughput at 25 MHz is sufficient to execute field-oriented control (FOC) or trapezoidal commutation within the typical 10-50 us loop budget for stepper and BLDC drives. Its 16 KB OTP program memory holds lookup tables for sine commutation and PID state while leaving headroom for fault handling. The 58-instruction RISC core simplifies certification review because the entire instruction set is auditable, and the 44-pin TQFP provides ample GPIO for Hall sensors, PWM channels, and quadrature encoder inputs. Pair with the IRF540N MOSFET for low-side switching.
추천
Automotive Body Electronics (Legacy)
The PIC17C44-25/PT is well suited to legacy automotive body modules such as central locking, mirror control, and lighting controllers where its 8-bit Harvard RISC core, 16 KB OTP memory, and 25 MHz throughput provide enough headroom for CAN-state-machine logic and debounce handling. The TQFP-44 footprint integrates cleanly onto through-hole or mixed-technology automotive PCBs. Note that this part is not AEC-Q100 qualified; new automotive designs should consider AEC-Q100-qualified PIC18F alternatives. The PIC17C44-25I/PT industrial-temperature variant is preferred for under-hood or engine-bay-adjacent placement.
추천
Process Control Instrumentation
For process-control transmitters, panel meters, and data-loggers, the PIC17C44-25/PT's deterministic 121 ns instruction cycle simplifies accurate timing of ADC reads and pulse-width measurements. Its 16 KB OTP accommodates 4-20 mA loop linearization tables, HART-state-machine code, and small protocol stacks. The Harvard architecture with separate program/data buses prevents DMA-style bus contention common in 8051 derivatives, and the 58-instruction set eases code review for IEC 61508-related functional-safety reviews. Suitable companion parts include the MCP3421 18-bit ADC for precision analog measurement.
추천
Embedded Control Systems (General Purpose)
General-purpose embedded controllers - HVAC zone controllers, vending machine subsystems, security panels, and small appliances - match well with the PIC17C44-25/PT's 8-bit RISC performance and 16 KB OTP. The PIC17 family is upward-compatible with PIC16C5X/PIC12CXXX/PIC16CXX code, allowing code portability from older Microchip designs without rewrites. The TQFP-44 package suits both hand-solder prototypes and high-volume SMT assembly. Use the 25 MHz throughput for keypad scanning, character-LCD refresh, and serial-port handling simultaneously without timing-slice contention.
추천
Medical Monitoring Devices (Non-Critical)
The PIC17C44-25/PT fits non-critical medical monitoring peripherals - patient-bedside displays, infusion-pump keypads, or therapy-device user interfaces - where 8.25 MIPS drives LCD graphics and keypad scanning without overrunning real-time deadlines. Its Harvard RISC core delivers predictable interrupt latency, an important property for medical IEC 60601-1 timing budgets. The OTP memory locks firmware for FDA traceability. Designers targeting FDA submission paths should validate with the actual PIC17C44-25/PT silicon rather than rely on simulation; pair with the MCP1700 LDO for clean supply rails.
추천
Consumer Appliance Controllers
Consumer appliances such as washing-machine control boards, dishwasher timers, and microwave oven interfaces are well served by the PIC17C44-25/PT because its 16 KB OTP holds segmented state machines, fault-detection logic, and display driver routines within a single chip. The 44-pin TQFP provides sufficient I/O for seven-segment displays, button matrices, and triac-driven load drivers. Production economics improve at qty 1000+ where the unit price approaches $7.80 per piece as of 2026-09-25. Pair with the MOC3021 optoisolator for triac drive.
추천
추천 제품 요약
엔지니어링 참조 데이터: PIC17C44-25/PT — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | PIC17C44-25I/PT | PIC17C44-16I/PT | PIC17C44T-25/PT | PIC17C44-33/PT | PIC17C44-25I/L |
|---|---|---|---|---|---|---|
| Package | TQFP-44 (PT) - 10x10 mm | TQFP-44 (PT) - same | TQFP-44 (PT) - same | TQFP-44 (PT) - same | TQFP-44 (PT) - same | TQFP-44 (PT) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Maximum Clock Frequency | 25 MHz | 25 MHz | 16 MHz | 25 MHz | 33 MHz | 25 MHz |
| Program Memory Size | 16 KB OTP | 16 KB OTP | 16 KB OTP | 16 KB OTP | 16 KB OTP | 16 KB OTP |
| Operating Temperature Grade | Commercial (0C to +70C) | Industrial (-40C to +85C) | Industrial (-40C to +85C) | Commercial (0C to +70C) | Commercial (0C to +70C) | Industrial (-40C to +85C) |
| Throughput (MIPS) | 8.25 MIPS | 8.25 MIPS | 5.28 MIPS | 8.25 MIPS | 10.89 MIPS | 8.25 MIPS |
| Supply Voltage | 5 V nominal | 5 V nominal | 5 V nominal | 5 V nominal | 5 V nominal | 5 V nominal |
| Instruction Set Size | 58 single-word instructions | 58 single-word instructions | 58 single-word instructions | 58 single-word instructions | 58 single-word instructions | 58 single-word instructions |
| Architecture | PIC17 Harvard RISC | PIC17 Harvard RISC | PIC17 Harvard RISC | PIC17 Harvard RISC | PIC17 Harvard RISC | PIC17 Harvard RISC |
주요 차별점
- Highest-throughput 8-bit PIC17 OTP at 25 MHz (vs PIC17C44-16I/PT)
- True drop-in TQFP-44 form factor across speed grades (vs PIC17C44-25I/PT)
- Microchip-exclusive PIC17 architecture (vs PIC18F442 (recommended by Microchip for new designs))
설계 노트
The PIC17C44-25/PT operates from a single 5V supply on the VDD pin (pin 36) with VSS (pin 35) as ground return. Place a 100 nF decoupling capacitor as close as physically possible to the VDD pin, with a bulk 10 uF tantalum or ceramic on the same supply rail. The PIC17 family does not include an internal POR circuit on all silicon revisions; an external supervisor such as MCP100 or MCP130 is recommended for cold-start reliability, especially in industrial motor-control installations where brown-out recovery is critical. Estimated: typical active current is 30-50 mA at 25 MHz; idle via SLP instruction drops to ~10 uA.
Route the 25 MHz OSC1/OSC2 traces as short, impedance-controlled paths; place the crystal or resonator within 5 mm of pins 8 and 37. The TQFP-44 0.8 mm pitch allows escape routing on a 4-layer PCB but requires via-in-pad or dog-bone fan-outs on 2-layer boards. Separate analog references (AVDD/AVSS if used) from digital switching traces. The MCLR/VPP pin (pin 38) needs a 10 kohm pull-up to VDD and a 100 nF capacitor to ground for ICSP programming; do not place large capacitors directly on MCLR because this slows reset edge transitions. Estimated trace lengths under 10 mm are recommended for the oscillator circuit.
Do not exceed 25 MHz at the OSC1 input - faster signals require the PIC17C44-33 variant. Program branches (GOTO, CALL) and table reads/writes take two instruction cycles (242 ns), not one; calculate worst-case interrupt latency assuming a 2-cycle pre-fetch stall. The OTP program memory cannot be reprogrammed in-circuit, so verify code with a windowed PIC17C44JW or PIC17C44 emulator before committing to OTP parts for production. Avoid using both INT (RB0) and the RB port-change interrupt simultaneously because shared registers require careful flag management. Per Microchip Microchip forum guidance, PIC18F442 is NOT a pin-for-pin replacement, so do not assume drop-in compatibility when migrating to PIC18.
The PIC17C44-25/PT I/O ports are CMOS with TTL-compatible input thresholds; ensure that signals crossing between 3.3V peripherals and the 5V PIC17 are level-translated (e.g. with a 74LVC245 or simple resistor divider on inputs only). Long PCB traces (>50 mm) on PORTB or PORTC should be series-terminated with 33-47 ohm resistors to dampen ringing at 25 MHz instruction throughput, especially when driving capacitive loads. Use guard traces or ground pours adjacent to oscillator traces to minimize EMI susceptibility per CISPR 22 industrial-emissions compliance.
규정 준수 정보
RoHS, REACH, lead-free, halogen-free, and conflict-mineral compliance status were not explicitly stated in the retrieved distributor or manufacturer pages and are marked as 'unknown'. AEC-Q100 is 'not_applicable' because the PIC17C44 is not marketed as an automotive-qualified MCU; new automotive designs should consider AEC-Q100-qualified PIC18 variants.
