PIC18F46Q10-I/PT - 64KB Flash 8-bit MCU | Microchip | TQFP-44
부품 번호: PIC18F46Q10-I/PT ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $2.85 | $2.85 |
| 10 | $2.52 | $25.20 |
| 100 | $2.18 | $218.00 |
| 500 | $1.92 | $960.00 |
| 1,000 | $1.71 | $1,710.00 |
| 3,000 | $1.55 | $4,650.00 |
PIC18F46Q10-I/PT 개요
A PIC18 microcontroller is a member of Microchip's enhanced 8-bit RISC architecture family, positioned within the broader microcontroller -> embedded controller -> semiconductor hierarchy. PIC18 devices extend the baseline PIC16 instruction set with hardware multiply, larger linear addressing windows, and C-optimized compiler support from MPLAB XC8. The Q10 sub-family specifically adds eXtreme Low Power (XLP) modes, integrated op-amps/comparators, and peripherals oriented toward closed-loop real-time control and sensor-node designs, distinguishing it from older PIC18F K-series parts that prioritize raw throughput.
Key differentiating features include Core Independent Peripherals (CIPs) such as the 16-bit PWM with complementary outputs and dead-band control, the CWG (Complementary Waveform Generator), and the Numerically Controlled Oscillator (NCO). Functional Safety (FuSa) support includes a Windowed Watchdog Timer, CRC/Scan module for memory integrity, and a Hardware Limit Timer (HLT) for actuator protection - features that simplify IEC 61508 / SIL-2 design paths for industrial sensors and motor-control front-ends.
Typical applications include industrial sensor nodes, HVAC actuator control, low-power IoT edge devices, automotive body and lighting modules, white goods motor control, and consumer touch-sensing front panels. The 5V native I/O tolerance increases noise immunity in factory-floor environments where 3.3V-only MCUs are marginal.
When designing with this device, ensure the configuration bits are locked via the Configuration Word register before any Flash programming. For low-power IoT use cases, enable the nanoWatt XLP Sleep mode with RTC wake - this typically draws less than 50 nA. Use the ADC2 with hardware averaging and threshold compare to offload CPU cycles in sensor-fusion loops.
This page synthesizes distributor pricing, drop-in PIC18 alternatives, and practical design notes not found in the manufacturer datasheet, providing engineering teams with consolidated selection and procurement guidance.
드롭인 대체품: PIC18F46Q10-I/PT — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: PIC18F46Q10-I/PT (동일 폼 팩터 및 풋프린트) — 차이점: Package, ADC, Program Memory (Flash), DAC, Core Architecture.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
PIC18F45Q10-I/PT
✅ 드롭인✓ 재고 있음
$1.39 / 개
데이터시트 보기 →PIC18F46Q10-I/PTVAO
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC18F46K22-I/PT
✅ 드롭인✓ 재고 있음
$2.32 / 개
데이터시트 보기 →PIC18F45K22-I/PT
✅ 드롭인✓ 재고 있음
$2.65 / 개
데이터시트 보기 →PIC18F46K40-I/PT
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC16LF15386-I/PT
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$1.95 / 개
데이터시트 보기 →PIC18F46Q10-I/PT 최대 정격 & 전기적 특성
| Core Architecture | 8-bit PIC18 enhanced RISC |
| Program Memory (Flash) | 64 KB |
| SRAM | 3,728 bytes (3728 B) |
| EEPROM | 1,024 bytes (1024 B) |
| Maximum CPU Frequency | 64 MHz |
| Operating Voltage Range | 2.5 V to 5.5 V |
| I/O Pins | 36 |
| ADC | 10-bit ADC2 (with Computation) |
| DAC | 5-bit and 10-bit DAC |
| 패키지 | 44-pin TQFP (10x10 mm) |
| 동작 온도 | -40C to +85C (Industrial) |
| 실장 유형 | Surface Mount |
| Family | PIC XLP 18Q, Functional Safety (FuSa) |
| RoHS 상태 | Compliant |
| MSL 레벨 | 3 |
PIC18F46Q10-I/PT 핀 구성
| 핀 1 | RA2 — Port A bit 2 / analog input |
| 핀 2 | RA3 — Port A bit 3 / analog input |
| 핀 3 | RA4 — Port A bit 4 / analog input |
| 핀 4 | RA5 — Port A bit 5 / analog input |
| 핀 5 | RA6 — Port A bit 6 / analog input |
| 핀 6 | RA7 — Port A bit 7 / analog input |
| 핀 7 | VSS — Ground reference |
| 핀 8 | VDD — Positive supply voltage |
| 핀 9 | OSC1 — Crystal oscillator input |
| 핀 10 | OSC2 — Crystal oscillator output |
| 핀 11 | RC0 — Port C bit 0 |
| 핀 12 | RC1 — Port C bit 1 |
| 핀 13 | RC2 — Port C bit 2 |
| 핀 14 | RC3 — Port C bit 3 |
| 핀 15 | RC4 — Port C bit 4 |
| 핀 16 | RC5 — Port C bit 5 |
| 핀 17 | RC6 — Port C bit 6 |
| 핀 18 | RC7 — Port C bit 7 |
| 핀 19 | VSS — Ground reference |
| 핀 20 | VDD — Positive supply voltage |
| 핀 21 | RB0 — Port B bit 0 |
| 핀 22 | RB1 — Port B bit 1 |
| 핀 23 | RB2 — Port B bit 2 |
| 핀 24 | RB3 — Port B bit 3 |
| 핀 25 | RB4 — Port B bit 4 |
| 핀 26 | RB5 — Port B bit 5 |
| 핀 27 | RB6 — Port B bit 6 / ICSP PGC |
| 핀 28 | RB7 — Port B bit 7 / ICSP PGD |
| 핀 29 | MCLR — Master clear reset input |
| 핀 30 | RE3 — Port E bit 3 |
| 핀 31 | RD0 — Port D bit 0 |
| 핀 32 | RD1 — Port D bit 1 |
| 핀 33 | RD2 — Port D bit 2 |
| 핀 34 | RD3 — Port D bit 3 |
| 핀 35 | RD4 — Port D bit 4 |
| 핀 36 | RD5 — Port D bit 5 |
| 핀 37 | RD6 — Port D bit 6 |
| 핀 38 | RD7 — Port D bit 7 |
| 핀 39 | VSS — Ground reference |
| 핀 40 | VDD — Positive supply voltage |
| 핀 41 | RE0 — Port E bit 0 |
| 핀 42 | RE1 — Port E bit 1 |
| 핀 43 | RE2 — Port E bit 2 |
| 핀 44 | AVSS — Analog ground |
일반적인 애플리케이션
PIC18F46Q10-I/PT 적합 용도: 7 애플리케이션s: Industrial Sensor Nodes, HVAC Actuator Control, Low-Power IoT Edge Devices, Automotive Body and Lighting Modules, White Goods Motor Control, Consumer Touch-Sensing Front Panels, Portable Medical Monitoring.
Industrial Sensor Nodes
The PIC18F46Q10-I/PT is engineered for industrial sensor nodes that require robust 5V noise immunity and integrated Functional Safety peripherals. Its 64 KB Flash accommodates MODBUS/RTU and IO-Link protocol stacks plus application firmware, while the 10-bit ADC2 with Computation performs threshold-based scanning without CPU intervention. The Windowed WDT and CRC/Scan module support IEC 61508 SIL-2 design paths, and the nanoWatt XLP Sleep mode (under 50 nA) enables battery-backed wireless sensor deployments with multi-year coin-cell lifetimes.
추천
HVAC Actuator Control
HVAC damper and valve actuators benefit from the PIC18F46Q10-I/PT's Complementary Waveform Generator (CWG) and 16-bit PWM with dead-band control, which directly drive H-bridge FET stages for three-phase brushless DC or stepper motors. The Hardware Limit Timer (HLT) provides hardware-enforced actuator travel limits independent of firmware, increasing SIL-2 safety margins. With 5V I/O tolerance, the MCU interfaces directly to industrial 24V-referenced feedback signals through resistive dividers, simplifying the analog front end in damper position feedback loops.
추천
Low-Power IoT Edge Devices
Battery-powered IoT edge nodes leverage the PIC18F46Q10-I/PT's eXtreme Low Power XLP Sleep modes drawing under 50 nA with RTC retention, enabling multi-year lifetimes on a single CR2032 coin cell. The 64 KB Flash comfortably hosts BLE/Zigbee protocol stacks plus sensor-fusion firmware. Core Independent Peripherals like the NCO and CWG run autonomously in Sleep, waking the CPU only on threshold events from the ADC2 with Computation, dramatically reducing average power consumption in event-driven sensing.
추천
Automotive Body and Lighting Modules
The PIC18F46Q10-I/PT, including the VAO (Vehicle AEC-Q100 Optional) screened variant, supports automotive body controllers and lighting modules. Its 5V I/O tolerance interfaces with legacy 12V automotive sensors through simple resistor dividers, and the 64 MHz CPU clock executes LIN stack plus lighting fade algorithms in real time. The CWG drives LED strings with hardware PWM dimming while the Windowed WDT prevents runaway firmware in the harsh automotive electrical environment with load-dump transients up to 40V.
추천
White Goods Motor Control
Washing machines, dishwashers, and refrigerators use the PIC18F46Q10-I/PT as the main motor and user-interface controller. The 16-bit PWM with complementary outputs drives inverter-stage IGBTs for BLDC compressor motors, while the ADC2 samples motor current for sensorless FOC algorithms. Hardware Limit Timer provides independent over-current protection, and the 64 KB Flash supports multiple motor control profiles and OEM diagnostic routines in a single firmware image, reducing SKU complexity for appliance manufacturers.
추천
Consumer Touch-Sensing Front Panels
Consumer products with capacitive touch panels benefit from the PIC18F46Q10-I/PT's integrated MTCH (mTouch) capacitive sensing module, which provides hardware-driven proximity and touch detection without CPU overhead. The 64 KB Flash hosts USB device stacks for touch-panel data reporting, while the CWG drives haptic feedback actuators. nanoWatt XLP Sleep modes maintain touch wake-up at under 1 microamp average, enabling battery-powered remote controls and portable touch interfaces with year-long battery life.
추천
Portable Medical Monitoring
Battery-powered patient monitors and pulse oximeters use the PIC18F46Q10-I/PT for its low-power Sleep modes with RTC retention and 10-bit ADC2 with averaging for vital-sign signal conditioning. The 64 KB Flash supports FDA 510(k) firmware with secure boot via CRC/Scan integrity checks. The 5V-tolerant I/O interfaces directly to legacy medical sensors, and the eXtreme Low Power modes enable continuous overnight SpO2 monitoring on rechargeable Li-ion cells without operator intervention.
추천
추천 제품 요약
엔지니어링 참조 데이터: PIC18F46Q10-I/PT — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | PIC18F45Q10-I/PT | PIC18F46Q10-I/PTVAO | PIC18F46K22-I/PT | PIC18F45K22-I/PT | PIC18F46K40-I/PT | PIC16LF15386-I/PT |
|---|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 44-pin TQFP (10x10) | 44-pin TQFP (10x10) - same | 44-pin TQFP (10x10) - same | 44-pin TQFP (10x10) - same | 44-pin TQFP (10x10) - same | 44-pin TQFP (10x10) - same | 44-pin TQFP (10x10) - same |
| Flash Memory | 64 KB | 32 KB (-50%) | 64 KB (same) | 64 KB (same) | 32 KB (-50%) | 64 KB (same) | 28 KB (-56%) |
| SRAM | 3,728 bytes | 2,048 bytes | 3,898 bytes | 2,048 bytes | |||
| CPU Architecture | PIC18 enhanced 8-bit | PIC18 enhanced 8-bit | PIC18 enhanced 8-bit | PIC16 baseline 8-bit (different core) | |||
| Max CPU Frequency | 64 MHz | 64 MHz | 64 MHz | 32 MHz (-50%) | |||
| Operating Voltage | 2.5V to 5.5V | 2.5V to 5.5V | 1.8V to 3.6V (different range) | ||||
| ADC | 10-bit ADC2 (Computation) | 10-bit ADC2 (Computation) | 10-bit legacy ADC (no ADC2) | 10-bit ADC | |||
| Functional Safety Features | WWDT, CRC/Scan, HLT | WDT only (no CRC/Scan, no HLT) | WDT only | ||||
| Core Independent Peripherals | CWG, NCO, PWM, ADC2 | ECCP, MSSP (no CWG/NCO/ADC2) | CWG, NCO (no ADC2) |
주요 차별점
- Newer CIPs with ADC2 Computation offload (vs PIC18F46K22-I/PT)
- Integrated Functional Safety peripherals (vs PIC18F46K40-I/PT)
- eXtreme Low Power Sleep under 50 nA (vs PIC16LF15386-I/PT)
- Automotive VAO screening option (vs PIC18F46Q10-I/PTVAO)
설계 노트
The PIC18F46Q10-I/PT operates from 2.5V to 5.5V with separate analog (AVDD/AVSS) and digital (VDD/VSS) supply pins. Decouple each VDD pin with a 100 nF ceramic capacitor placed within 3 mm of the pin, plus a bulk 10 uF tantalum or ceramic capacitor at the package. For ADC accuracy above 10 ENOB, add a small ferrite bead between AVDD and VDD and place a separate 100 nF + 10 uF decoupling network directly on AVDD. Tie all VSS pins to a single ground plane; do not split analog and digital grounds.
Configuration bits in the CONFIG words must be programmed before any Flash application code execution - failure to lock the configuration words results in the device defaulting to a non-functional clock source. The MCLR pin requires a 10 kohm pull-up to VDD; do not leave it floating, or use the internal MCLR disable configuration bit only in production designs. When migrating from PIC18F K-series firmware, the ADC registers have changed substantially - do not assume legacy ADC register names apply.
Route the ICSP PGC/PGD lines (RB6/RB7) directly to a 6-pin ICSP header with no series resistors on the data lines, and keep traces short (<50 mm) to avoid programming failures. The 44-pin TQFP 10x10 mm package has a 0.8 mm pitch - use 0.4 mm-wide traces between pads and ensure your PCB manufacturer's minimum clearance rules support this. For high-speed oscillator operation above 20 MHz, place a ground guard ring around the crystal and load capacitors.
The 44-pin TQFP package dissipates approximately 1 W maximum at 64 MHz full-load operation across all GPIO. Estimated: at 5V supply, 64 MHz, all peripherals active, and 36 GPIO sourcing 10 mA each, the die dissipates roughly 800 mW with theta_JA around 50 C/W, yielding a 40 C temperature rise above ambient. For industrial -40C to +85C ambient operation, this is acceptable; for high-temperature environments above 70 C ambient, consider the PIC18F46Q10-E/PT extended-temperature variant.
규정 준수 정보
RoHS compliant per Microchip product page. Industrial -I temperature grade -40C to +85C. The PIC18F46Q10-I/PTVAO automotive variant provides AEC-Q100 screening for vehicle applications; the standard -I/PT is not AEC-Q100 qualified.