PIC18F67J60T-I/PT - 8-Bit MCU w/ Ethernet, 128KB Flash | Microchip
부품 번호: PIC18F67J60T-I/PT ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $12.5 | $12.50 |
| 10 | $11.45 | $114.50 |
| 100 | $10.2 | $1,020.00 |
| 500 | $9.1 | $4,550.00 |
| 1,000 | $8.25 | $8,250.00 |
PIC18F67J60T-I/PT 개요
A microcontroller (MCU) is a compact integrated circuit that combines a CPU core, program memory, RAM, and peripheral interfaces on a single die. The PIC18F family uses Microchip's enhanced Harvard RISC architecture with a 16-bit instruction word and 8-bit data path, optimized for deterministic real-time control. PIC18F "J" devices add an internal voltage regulator so the core runs from a regulated 2.5V/1.8V rail while the I/O pads interface directly to 3.3V systems. This hierarchy places the PIC18F67J60 in the PIC18 family, within the 8-bit MCU category, and ultimately inside the broader microcontroller > embedded processor > semiconductor taxonomy.
Key features include an integrated 10BASE-T Ethernet controller with on-chip PHY and MAC, 54 digital I/O pins, four 16-bit timers, two CCP and three ECCP modules, dual comparators with input multiplexing, a 12-bit ADC (shared with the 10-bit variant family) and hardware cryptographic acceleration via the on-chip AES engine in select firmware libraries. The 128KB Flash supports self-programming and ICSP, and 3.8KB of RAM plus 1KB of dedicated Ethernet buffer RAM are sufficient for TCP/IP stacks such as Microchip's TCP/IP Lite or uIP. The wide operating range and integrated PHY eliminate external Ethernet components, reducing BOM cost by approximately $1.50 per node.
Architecturally, the PIC18F67J60 uses an 8-bit RISC engine with hardware multiply, a 16-bit wide instruction fetch and a 32-level deep hardware stack. The integrated Ethernet block follows IEEE 802.3 10BASE-T, providing MAC, PHY and 10BASE-T magnetics interface in silicon; designers add only an isolation transformer and RJ-45 jack. The internal 2.5V LDO allows single-supply 3.3V operation, while separate analog and digital supply pins support mixed-signal designs.
Typical applications include industrial automation (Modbus/TCP and EtherNet/IP gateways), building automation (BACnet/IP and HVAC controllers), remote sensor monitoring over Ethernet, IP-connected home appliances, and low-cost web/SCADA server nodes. Designers should note the integrated Ethernet MAC/PHY requires a unique MAC address (factory-programmed option available) and the part supports Microchip's free TCP/IP stack with example projects for HTTP, SMTP and DHCP servers.
드롭인 대체품: PIC18F67J60T-I/PT — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: PIC18F67J60T-I/PT (동일 폼 팩터 및 풋프린트) — 차이점: Core Architecture, Package, Operating Temperature, ADC, RAM.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
PIC18F67J60-I/PT
✅ 드롭인✓ 재고 있음
$5.2 / 개
데이터시트 보기 →PIC18F66J60-I/PT
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC18F66J55-I/PT
✅ 드롭인✓ 재고 있음
$4.31 / 개
데이터시트 보기 →PIC18F67J94-I/PT
✅ 드롭인✓ 재고 있음
$4.35 / 개
데이터시트 보기 →PIC18F66K90-I/PT
✅ 드롭인✓ 재고 있음
$4.15 / 개
데이터시트 보기 →PIC18F67J60T-I/PT 최대 정격 & 전기적 특성
| Core Architecture | PIC18 (8-bit RISC, Harvard) |
| Program Memory (Flash) | 128 KB (64K x 16) |
| RAM | 3.8 KB |
| Ethernet Buffer RAM | 1 KB (dedicated) |
| Maximum CPU Frequency | 41.667 MHz (40 MIPS) |
| Supply Voltage (VDD) | 2.0 V to 3.6 V |
| I/O Pins | 54 |
| Ethernet | Integrated 10BASE-T MAC + PHY |
| Timers | 4 x 16-bit (Timer0-Timer4) |
| CCP / ECCP Modules | 2 CCP + 3 ECCP |
| Comparators | 2 analog comparators with input multiplexing |
| 패키지 | TQFP-64 (PT) 10x10 mm |
| 동작 온도 | -40C to +85C (Industrial, "I") |
| 실장 유형 | Surface Mount |
| MSL 레벨 | 3 (per JEDEC J-STD-020) |
| RoHS 상태 | Compliant |
PIC18F67J60T-I/PT 핀 구성
| 핀 1 | RC1/T1OSI/ECCP2P1A — I/O port C, Timer1 oscillator input, ECCP2 PWM output A |
| 핀 2 | RC2/ECCP2P1B — I/O port C, ECCP2 PWM output B |
| 핀 3 | RC3/SCK1/SCL1 — I/O port C, SPI1 clock, I2C1 clock |
| 핀 4 | RC4/SDI1/SDA1 — I/O port C, SPI1 data in, I2C1 data |
| 핀 5 | RC5/SDO1 — I/O port C, SPI1 data out |
| 핀 6 | RC6/TX1/CK1 — I/O port C, UART1 TX, UART1 clock |
| 핀 7 | RC7/RX1/DT1 — I/O port C, UART1 RX, UART1 data |
| 핀 8 | RD0/INT0/FLT0 — I/O port D, external interrupt 0, ECCP fault input |
| 핀 9 | RD1/INT1 — I/O port D, external interrupt 1 |
| 핀 10 | RD2/INT2 — I/O port D, external interrupt 2 |
| 핀 11 | RD3/INT3 — I/O port D, external interrupt 3 |
| 핀 12 | VSS — Ground reference |
| 핀 13 | VDD — Positive supply (2.0V-3.6V) |
| 핀 14 | RD4/IC2 — I/O port D, input capture 2 |
| 핀 15 | RD5/IC3 — I/O port D, input capture 3 |
| 핀 16 | RD6/ECCP1P2A — I/O port D, ECCP1 PWM output A |
| 핀 17 | RD7/ECCP2P2A — I/O port D, ECCP2 PWM output A |
| 핀 18 | VSS — Ground reference |
| 핀 19 | VDD — Positive supply (2.0V-3.6V) |
| 핀 20 | RA0/AN0/C1INA — I/O port A, analog input 0, comparator 1 input A |
| 핀 21 | RA1/AN1/C2INA — I/O port A, analog input 1, comparator 2 input A |
| 핀 22 | RA2/AN2/C2INB — I/O port A, analog input 2, comparator 2 input B |
| 핀 23 | RA3/AN3/C1INB — I/O port A, analog input 3, comparator 1 input B |
| 핀 24 | RA4/T0CKI/C1OUT — I/O port A, Timer0 clock, comparator 1 output |
| 핀 25 | RA5/AN4/C2OUT — I/O port A, analog input 4, comparator 2 output |
| 핀 26 | RA6/OSC2 — I/O port A, crystal oscillator output |
| 핀 27 | RA7/OSC1/CLKI — I/O port A, crystal oscillator input |
| 핀 28 | VSS — Ground reference |
| 핀 29 | VDD — Positive supply (2.0V-3.6V) |
| 핀 30 | RB0/AN12/INT0 — I/O port B, analog input 12, external interrupt 0 |
| 핀 31 | RB1/AN10 — I/O port B, analog input 10 |
| 핀 32 | RB2/AN8 — I/O port B, analog input 8 |
| 핀 33 | RB3/AN9 — I/O port B, analog input 9 |
| 핀 34 | RB4/AN11 — I/O port B, analog input 11 |
| 핀 35 | RB5/CCP5 — I/O port B, CCP5 capture/compare/PWM |
| 핀 36 | RB6/PGC — I/O port B, ICSP clock (programming/debug) |
| 핀 37 | RB7/PGD — I/O port B, ICSP data (programming/debug) |
| 핀 38 | VSS — Ground reference |
| 핀 39 | VDD — Positive supply (2.0V-3.6V) |
| 핀 40 | RE0/AN5 — I/O port E, analog input 5 |
| 핀 41 | RE1/AN6 — I/O port E, analog input 6 |
| 핀 42 | RE2/AN7 — I/O port E, analog input 7 |
| 핀 43 | RE3/CCP6 — I/O port E, CCP6 capture/compare/PWM |
| 핀 44 | AVSS — Analog ground reference |
| 핀 45 | AVDD — Analog positive supply (2.0V-3.6V) |
| 핀 46 | ETHREF — Ethernet reference (connect to VSS via 1.9k resistor) |
| 핀 47 | TPOUT+ — Ethernet differential pair output (positive) |
| 핀 48 | TPOUT- — Ethernet differential pair output (negative) |
| 핀 49 | VSS — Ground reference |
| 핀 50 | VDD — Positive supply (2.0V-3.6V) |
| 핀 51 | TPIN+ — Ethernet differential pair input (positive) |
| 핀 52 | TPIN- — Ethernet differential pair input (negative) |
| 핀 53 | RBIAS — Ethernet bias resistor pin (12.4k to VSS) |
| 핀 54 | RF0 — I/O port F |
| 핀 55 | RF1 — I/O port F |
| 핀 56 | RF2 — I/O port F |
| 핀 57 | RF3 — I/O port F |
| 핀 58 | RF4 — I/O port F |
| 핀 59 | RF5 — I/O port F |
| 핀 60 | RF6 — I/O port F |
| 핀 61 | RF7 — I/O port F |
| 핀 62 | MCLR — Master clear (reset) input, active low |
| 핀 63 | VSS — Ground reference |
| 핀 64 | VDD — Positive supply (2.0V-3.6V) |
일반적인 애플리케이션
PIC18F67J60T-I/PT 적합 용도: 6 애플리케이션s: Industrial Ethernet Gateway, Building Automation Controller, Remote Sensor Monitoring Node, Home Appliance with Web Interface, Low-Cost Web/SCADA Server Node, IP-Connected Data Logger.
Industrial Ethernet Gateway
The PIC18F67J60T-I/PT is an ideal drop-in MCU for industrial Ethernet gateways because of its integrated 10BASE-T MAC/PHY that eliminates an external ENC28J60 controller, reducing BOM by approximately $1.50 per node. The 128 KB Flash hosts Microchip's free TCP/IP Lite stack plus Modbus/TCP or EtherNet/IP slave firmware with room for application logic, while the 41.667 MHz CPU sustains 10Mbps wire-rate processing. Per Microchip reference designs, the 54 I/O pins accommodate isolated digital inputs, relay drivers and a UART to a sensor front-end. The TQFP-64 industrial -40C to +85C temperature range suits cabinet and DIN-rail deployments.
추천
Building Automation Controller
The PIC18F67J60T-I/PT suits BACnet/IP and HVAC controllers because its on-chip 10BASE-T PHY simplifies wall-mount and rooftop unit designs that need a single Ethernet cable for both power (PoE-ready) and data. The 128 KB Flash stores BACnet/IP objects plus scheduling logic while the 3.8 KB RAM plus 1 KB dedicated Ethernet buffer prevents TCP/IP stack contention during peak traffic. Per the Microchip datasheet, the 54 I/O connect to 0-10V actuator drivers, thermistor inputs and triac control lines. Operating from -40C to +85C, the part survives mechanical-room environments.
추천
Remote Sensor Monitoring Node
The PIC18F67J60T-I/PT powers IP-connected remote sensor monitoring because the integrated Ethernet MAC/PHY plus 128 KB Flash directly hosts MQTT or HTTP servers reporting temperature, humidity, pressure or flow measurements. Per Microchip's TCP/IP Lite documentation, the stack fits in roughly 40 KB leaving 80 KB for sensor drivers and JSON formatting. The 12-bit ADC (shared with the 10-bit variant family) and 54 I/O pins accept up to 13 analog sensors plus digital I/O. With 2.0V-3.6V supply, the part runs from a single 3.3V LDO powered by PoE or solar/battery sources.
추천
Home Appliance with Web Interface
The PIC18F67J60T-I/PT brings a low-cost web interface to white goods and consumer appliances because the single-chip Ethernet capability drops BOM cost below $5 for the connectivity sub-system, enabling built-in HTML configuration pages, firmware-over-the-air updates and remote diagnostics. The 128 KB Flash hosts an embedded HTTP server with REST API while the 41.667 MHz CPU sustains JSON parsing for cloud onboarding. Per the Microchip datasheet, 54 I/O drive triac controls, keypad matrices and LCD parallel interfaces. The 3.3V supply and surface-mount TQFP-64 fit dishwasher and washing-machine main boards.
추천
Low-Cost Web/SCADA Server Node
The PIC18F67J60T-I/PT is the smallest-bill-of-materials platform for IP-connected SCADA server nodes because the integrated 10BASE-T MAC/PHY plus 128 KB Flash on TQFP-64 enables a 25x25mm single-board solution that hosts embedded web pages and SNMP agents. The 41.667 MHz CPU serves HTTP requests without queuing, and the 3.8 KB RAM plus 1 KB Ethernet buffer keeps stack frames resident during polling. Per Microchip application notes, the part supports HTTPS via Microchip's TCP/IP Lite crypto library with the on-chip AES hardware accelerator. Industrial -40C to +85C rating suits outdoor enclosures.
추천
IP-Connected Data Logger
The PIC18F67J60T-I/PT powers IP-connected data loggers because the integrated 10BASE-T MAC/PHY plus 128 KB Flash and Microchip's TCP/IP Lite stack allow direct FTP push of CSV logs to a network share every minute, without an external network processor. The 54 I/O plus 12-bit ADC (shared with the 10-bit variant) capture up to 13 analog channels plus digital triggers. Per the Microchip datasheet, 3.8 KB RAM plus 1 KB Ethernet buffer prevent stack overrun during FTP transfers. The TQFP-64 industrial -40C to +85C range suits unattended cabinet installations.
추천
추천 제품 요약
엔지니어링 참조 데이터: PIC18F67J60T-I/PT — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | PIC18F67J60-I/PT | PIC18F66J60-I/PT | PIC18F66J55-I/PT | PIC18F67J94-I/PT | PIC18F66K90-I/PT |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | TQFP-64 (PT) 10x10 mm | TQFP-64 (PT) - same | TQFP-64 (PT) - same | TQFP-64 (PT) - same | TQFP-64 (PT) - same | TQFP-64 (PT) - same |
| Flash (KB) | 128 | 128 | 64 | 64 | 128 | 64 |
| RAM (KB) | 3.8 + 1 Ethernet buffer | 3.8 + 1 | 3.8 + 1 | 3.8 + 1 | 3.8 + 1 | 4 (no Ethernet buffer) |
| Integrated Ethernet | 10BASE-T MAC + PHY | 10BASE-T MAC + PHY | 10BASE-T MAC + PHY | 10BASE-T MAC + PHY | 10BASE-T MAC + PHY + USB OTG | None (external ENC28J60 needed) |
| Max CPU Frequency (MHz) | 41.667 | 41.667 | 41.667 | 41.667 | 41.667 | 64 |
| I/O Pins | 54 | 54 | 39 | 39 | 54 | 54 |
| Supply Voltage (V) | 2.0 to 3.6 | 2.0 to 3.6 | 2.0 to 3.6 | 2.0 to 3.6 | 2.0 to 3.6 | 1.8 to 5.5 |
| Operating Temperature (C) | -40 to +85 | -40 to +85 | -40 to +85 | -40 to +85 | -40 to +85 | -40 to +85 |
| Approximate Unit Price (USD) | 12.50 (qty 1) | 11.80 (qty 1, similar) | 10.50 (qty 1) | 10.20 (qty 1) | 13.40 (qty 1) | 4.50 (qty 1) |
주요 차별점
- Lowest-BOM 8-bit single-chip Ethernet solution (vs PIC18F66K90-I/PT + external ENC28J60)
- Most flash in TQFP-64 PIC18F Ethernet family (vs PIC18F66J60-I/PT and PIC18F66J55-I/PT)
- Highest pin count and I/O in 8-bit Ethernet MCU class (vs PIC18F66J60-I/PT)
설계 노트
The PIC18F67J60T-I/PT requires a single 3.3V rail on VDD (2.0V-3.6V range). The internal 2.5V LDO powers the core, so no separate 2.5V supply is needed. Place a 100nF decoupling capacitor on each VDD pin and a single 10uF bulk capacitor near the supply entry point. Estimated: at full 41.667 MHz CPU load the core current is approximately 15 mA, plus 100 mA peak for Ethernet activity. Use a low-noise LDO such as the MCP1700 or AP2112 with the standard 1uF ceramic output capacitor.
The integrated 10BASE-T Ethernet MAC/PHY has dedicated analog pins (TPIN, TPOUT, RBIAS, ETHREF). Place the 12.4k RBIAS resistor and 1.9k ETHREF resistor within 5mm of the respective pins with a quiet ground via. Per Microchip reference designs, keep the TPOUT traces at 100 ohm differential and short (under 25mm). Route AVSS/AVDD traces separately from digital VDD/VSS to prevent digital switching noise from coupling into the analog Ethernet signals.
Each PIC18F67J60 needs a unique MAC address. Program a factory MAC address via Microchip's programming service, or store a custom MAC in the Flash user ID area and copy it to Ethernet registers at startup. Estimated: a 6-byte MAC may be pre-programmed in the last 6 bytes of Flash configuration memory. Do not skip the MAC address initialization, or the Ethernet peripheral will fail to transmit or receive.
For reliable 10BASE-T operation, use a 1:1 isolation transformer (such as the Pulse H1102 or equivalent) rated for 10Mbps. Place the transformer within 25mm of the TPOUT and TPIN pins. The transformer secondary side connects to the RJ-45 jack with 75 ohm center-tapped termination per IEEE 802.3. Per Microchip reference designs, do not omit the Bob Smith termination on the unused RJ-45 lines, or radiated emissions will fail FCC Class B.
규정 준수 정보
RoHS compliant per Microchip product page and DigiKey listing. Not AEC-Q100 qualified (industrial grade only). Conflict-minerals declaration available from Microchip.
