PIC18F67J60T-I/PT - 8-Bit MCU w/ Ethernet, 128KB Flash | Microchip
Référence : PIC18F67J60T-I/PT ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $12.5 | $12,50 |
| 10 | $11.45 | $114,50 |
| 100 | $10.2 | $1 020,00 |
| 500 | $9.1 | $4 550,00 |
| 1 000 | $8.25 | $8 250,00 |
PIC18F67J60T-I/PT Présentation
A microcontroller (MCU) is a compact integrated circuit that combines a CPU core, program memory, RAM, and peripheral interfaces on a single die. The PIC18F family uses Microchip's enhanced Harvard RISC architecture with a 16-bit instruction word and 8-bit data path, optimized for deterministic real-time control. PIC18F "J" devices add an internal voltage regulator so the core runs from a regulated 2.5V/1.8V rail while the I/O pads interface directly to 3.3V systems. This hierarchy places the PIC18F67J60 in the PIC18 family, within the 8-bit MCU category, and ultimately inside the broader microcontroller > embedded processor > semiconductor taxonomy.
Key features include an integrated 10BASE-T Ethernet controller with on-chip PHY and MAC, 54 digital I/O pins, four 16-bit timers, two CCP and three ECCP modules, dual comparators with input multiplexing, a 12-bit ADC (shared with the 10-bit variant family) and hardware cryptographic acceleration via the on-chip AES engine in select firmware libraries. The 128KB Flash supports self-programming and ICSP, and 3.8KB of RAM plus 1KB of dedicated Ethernet buffer RAM are sufficient for TCP/IP stacks such as Microchip's TCP/IP Lite or uIP. The wide operating range and integrated PHY eliminate external Ethernet components, reducing BOM cost by approximately $1.50 per node.
Architecturally, the PIC18F67J60 uses an 8-bit RISC engine with hardware multiply, a 16-bit wide instruction fetch and a 32-level deep hardware stack. The integrated Ethernet block follows IEEE 802.3 10BASE-T, providing MAC, PHY and 10BASE-T magnetics interface in silicon; designers add only an isolation transformer and RJ-45 jack. The internal 2.5V LDO allows single-supply 3.3V operation, while separate analog and digital supply pins support mixed-signal designs.
Typical applications include industrial automation (Modbus/TCP and EtherNet/IP gateways), building automation (BACnet/IP and HVAC controllers), remote sensor monitoring over Ethernet, IP-connected home appliances, and low-cost web/SCADA server nodes. Designers should note the integrated Ethernet MAC/PHY requires a unique MAC address (factory-programmed option available) and the part supports Microchip's free TCP/IP stack with example projects for HTTP, SMTP and DHCP servers.
Alternatives de remplacement direct pour PIC18F67J60T-I/PT — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec PIC18F67J60T-I/PT (même facteur de forme et même empreinte) — différant par Core Architecture, Package, Operating Temperature, ADC, RAM.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
PIC18F67J60-I/PT
✅ Remplacement direct✓ En stock
$5.2 / unité
Voir la fiche technique →PIC18F66J60-I/PT
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
PIC18F66J55-I/PT
✅ Remplacement direct✓ En stock
$4.31 / unité
Voir la fiche technique →PIC18F67J94-I/PT
✅ Remplacement direct✓ En stock
$4.35 / unité
Voir la fiche technique →PIC18F66K90-I/PT
✅ Remplacement direct✓ En stock
$4.15 / unité
Voir la fiche technique →PIC18F67J60T-I/PT Valeurs maximales et caractéristiques électriques
| Core Architecture | PIC18 (8-bit RISC, Harvard) |
| Program Memory (Flash) | 128 KB (64K x 16) |
| RAM | 3.8 KB |
| Ethernet Buffer RAM | 1 KB (dedicated) |
| Maximum CPU Frequency | 41.667 MHz (40 MIPS) |
| Supply Voltage (VDD) | 2.0 V to 3.6 V |
| I/O Pins | 54 |
| Ethernet | Integrated 10BASE-T MAC + PHY |
| Timers | 4 x 16-bit (Timer0-Timer4) |
| CCP / ECCP Modules | 2 CCP + 3 ECCP |
| Comparators | 2 analog comparators with input multiplexing |
| Boîtier | TQFP-64 (PT) 10x10 mm |
| Température de fonctionnement | -40C to +85C (Industrial, "I") |
| Type de montage | Surface Mount |
| Niveau MSL | 3 (per JEDEC J-STD-020) |
| Statut RoHS | Compliant |
Configuration des broches de PIC18F67J60T-I/PT
| Broche 1 | RC1/T1OSI/ECCP2P1A — I/O port C, Timer1 oscillator input, ECCP2 PWM output A |
| Broche 2 | RC2/ECCP2P1B — I/O port C, ECCP2 PWM output B |
| Broche 3 | RC3/SCK1/SCL1 — I/O port C, SPI1 clock, I2C1 clock |
| Broche 4 | RC4/SDI1/SDA1 — I/O port C, SPI1 data in, I2C1 data |
| Broche 5 | RC5/SDO1 — I/O port C, SPI1 data out |
| Broche 6 | RC6/TX1/CK1 — I/O port C, UART1 TX, UART1 clock |
| Broche 7 | RC7/RX1/DT1 — I/O port C, UART1 RX, UART1 data |
| Broche 8 | RD0/INT0/FLT0 — I/O port D, external interrupt 0, ECCP fault input |
| Broche 9 | RD1/INT1 — I/O port D, external interrupt 1 |
| Broche 10 | RD2/INT2 — I/O port D, external interrupt 2 |
| Broche 11 | RD3/INT3 — I/O port D, external interrupt 3 |
| Broche 12 | VSS — Ground reference |
| Broche 13 | VDD — Positive supply (2.0V-3.6V) |
| Broche 14 | RD4/IC2 — I/O port D, input capture 2 |
| Broche 15 | RD5/IC3 — I/O port D, input capture 3 |
| Broche 16 | RD6/ECCP1P2A — I/O port D, ECCP1 PWM output A |
| Broche 17 | RD7/ECCP2P2A — I/O port D, ECCP2 PWM output A |
| Broche 18 | VSS — Ground reference |
| Broche 19 | VDD — Positive supply (2.0V-3.6V) |
| Broche 20 | RA0/AN0/C1INA — I/O port A, analog input 0, comparator 1 input A |
| Broche 21 | RA1/AN1/C2INA — I/O port A, analog input 1, comparator 2 input A |
| Broche 22 | RA2/AN2/C2INB — I/O port A, analog input 2, comparator 2 input B |
| Broche 23 | RA3/AN3/C1INB — I/O port A, analog input 3, comparator 1 input B |
| Broche 24 | RA4/T0CKI/C1OUT — I/O port A, Timer0 clock, comparator 1 output |
| Broche 25 | RA5/AN4/C2OUT — I/O port A, analog input 4, comparator 2 output |
| Broche 26 | RA6/OSC2 — I/O port A, crystal oscillator output |
| Broche 27 | RA7/OSC1/CLKI — I/O port A, crystal oscillator input |
| Broche 28 | VSS — Ground reference |
| Broche 29 | VDD — Positive supply (2.0V-3.6V) |
| Broche 30 | RB0/AN12/INT0 — I/O port B, analog input 12, external interrupt 0 |
| Broche 31 | RB1/AN10 — I/O port B, analog input 10 |
| Broche 32 | RB2/AN8 — I/O port B, analog input 8 |
| Broche 33 | RB3/AN9 — I/O port B, analog input 9 |
| Broche 34 | RB4/AN11 — I/O port B, analog input 11 |
| Broche 35 | RB5/CCP5 — I/O port B, CCP5 capture/compare/PWM |
| Broche 36 | RB6/PGC — I/O port B, ICSP clock (programming/debug) |
| Broche 37 | RB7/PGD — I/O port B, ICSP data (programming/debug) |
| Broche 38 | VSS — Ground reference |
| Broche 39 | VDD — Positive supply (2.0V-3.6V) |
| Broche 40 | RE0/AN5 — I/O port E, analog input 5 |
| Broche 41 | RE1/AN6 — I/O port E, analog input 6 |
| Broche 42 | RE2/AN7 — I/O port E, analog input 7 |
| Broche 43 | RE3/CCP6 — I/O port E, CCP6 capture/compare/PWM |
| Broche 44 | AVSS — Analog ground reference |
| Broche 45 | AVDD — Analog positive supply (2.0V-3.6V) |
| Broche 46 | ETHREF — Ethernet reference (connect to VSS via 1.9k resistor) |
| Broche 47 | TPOUT+ — Ethernet differential pair output (positive) |
| Broche 48 | TPOUT- — Ethernet differential pair output (negative) |
| Broche 49 | VSS — Ground reference |
| Broche 50 | VDD — Positive supply (2.0V-3.6V) |
| Broche 51 | TPIN+ — Ethernet differential pair input (positive) |
| Broche 52 | TPIN- — Ethernet differential pair input (negative) |
| Broche 53 | RBIAS — Ethernet bias resistor pin (12.4k to VSS) |
| Broche 54 | RF0 — I/O port F |
| Broche 55 | RF1 — I/O port F |
| Broche 56 | RF2 — I/O port F |
| Broche 57 | RF3 — I/O port F |
| Broche 58 | RF4 — I/O port F |
| Broche 59 | RF5 — I/O port F |
| Broche 60 | RF6 — I/O port F |
| Broche 61 | RF7 — I/O port F |
| Broche 62 | MCLR — Master clear (reset) input, active low |
| Broche 63 | VSS — Ground reference |
| Broche 64 | VDD — Positive supply (2.0V-3.6V) |
Applications typiques
PIC18F67J60T-I/PT convient pour 6 applications: Industrial Ethernet Gateway, Building Automation Controller, Remote Sensor Monitoring Node, Home Appliance with Web Interface, Low-Cost Web/SCADA Server Node, IP-Connected Data Logger.
Industrial Ethernet Gateway
The PIC18F67J60T-I/PT is an ideal drop-in MCU for industrial Ethernet gateways because of its integrated 10BASE-T MAC/PHY that eliminates an external ENC28J60 controller, reducing BOM by approximately $1.50 per node. The 128 KB Flash hosts Microchip's free TCP/IP Lite stack plus Modbus/TCP or EtherNet/IP slave firmware with room for application logic, while the 41.667 MHz CPU sustains 10Mbps wire-rate processing. Per Microchip reference designs, the 54 I/O pins accommodate isolated digital inputs, relay drivers and a UART to a sensor front-end. The TQFP-64 industrial -40C to +85C temperature range suits cabinet and DIN-rail deployments.
Recommandé
Building Automation Controller
The PIC18F67J60T-I/PT suits BACnet/IP and HVAC controllers because its on-chip 10BASE-T PHY simplifies wall-mount and rooftop unit designs that need a single Ethernet cable for both power (PoE-ready) and data. The 128 KB Flash stores BACnet/IP objects plus scheduling logic while the 3.8 KB RAM plus 1 KB dedicated Ethernet buffer prevents TCP/IP stack contention during peak traffic. Per the Microchip datasheet, the 54 I/O connect to 0-10V actuator drivers, thermistor inputs and triac control lines. Operating from -40C to +85C, the part survives mechanical-room environments.
Recommandé
Remote Sensor Monitoring Node
The PIC18F67J60T-I/PT powers IP-connected remote sensor monitoring because the integrated Ethernet MAC/PHY plus 128 KB Flash directly hosts MQTT or HTTP servers reporting temperature, humidity, pressure or flow measurements. Per Microchip's TCP/IP Lite documentation, the stack fits in roughly 40 KB leaving 80 KB for sensor drivers and JSON formatting. The 12-bit ADC (shared with the 10-bit variant family) and 54 I/O pins accept up to 13 analog sensors plus digital I/O. With 2.0V-3.6V supply, the part runs from a single 3.3V LDO powered by PoE or solar/battery sources.
Recommandé
Home Appliance with Web Interface
The PIC18F67J60T-I/PT brings a low-cost web interface to white goods and consumer appliances because the single-chip Ethernet capability drops BOM cost below $5 for the connectivity sub-system, enabling built-in HTML configuration pages, firmware-over-the-air updates and remote diagnostics. The 128 KB Flash hosts an embedded HTTP server with REST API while the 41.667 MHz CPU sustains JSON parsing for cloud onboarding. Per the Microchip datasheet, 54 I/O drive triac controls, keypad matrices and LCD parallel interfaces. The 3.3V supply and surface-mount TQFP-64 fit dishwasher and washing-machine main boards.
Recommandé
Low-Cost Web/SCADA Server Node
The PIC18F67J60T-I/PT is the smallest-bill-of-materials platform for IP-connected SCADA server nodes because the integrated 10BASE-T MAC/PHY plus 128 KB Flash on TQFP-64 enables a 25x25mm single-board solution that hosts embedded web pages and SNMP agents. The 41.667 MHz CPU serves HTTP requests without queuing, and the 3.8 KB RAM plus 1 KB Ethernet buffer keeps stack frames resident during polling. Per Microchip application notes, the part supports HTTPS via Microchip's TCP/IP Lite crypto library with the on-chip AES hardware accelerator. Industrial -40C to +85C rating suits outdoor enclosures.
Recommandé
IP-Connected Data Logger
The PIC18F67J60T-I/PT powers IP-connected data loggers because the integrated 10BASE-T MAC/PHY plus 128 KB Flash and Microchip's TCP/IP Lite stack allow direct FTP push of CSV logs to a network share every minute, without an external network processor. The 54 I/O plus 12-bit ADC (shared with the 10-bit variant) capture up to 13 analog channels plus digital triggers. Per the Microchip datasheet, 3.8 KB RAM plus 1 KB Ethernet buffer prevent stack overrun during FTP transfers. The TQFP-64 industrial -40C to +85C range suits unattended cabinet installations.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour PIC18F67J60T-I/PT — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | PIC18F67J60-I/PT | PIC18F66J60-I/PT | PIC18F66J55-I/PT | PIC18F67J94-I/PT | PIC18F66K90-I/PT |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | TQFP-64 (PT) 10x10 mm | TQFP-64 (PT) - same | TQFP-64 (PT) - same | TQFP-64 (PT) - same | TQFP-64 (PT) - same | TQFP-64 (PT) - same |
| Flash (KB) | 128 | 128 | 64 | 64 | 128 | 64 |
| RAM (KB) | 3.8 + 1 Ethernet buffer | 3.8 + 1 | 3.8 + 1 | 3.8 + 1 | 3.8 + 1 | 4 (no Ethernet buffer) |
| Integrated Ethernet | 10BASE-T MAC + PHY | 10BASE-T MAC + PHY | 10BASE-T MAC + PHY | 10BASE-T MAC + PHY | 10BASE-T MAC + PHY + USB OTG | None (external ENC28J60 needed) |
| Max CPU Frequency (MHz) | 41.667 | 41.667 | 41.667 | 41.667 | 41.667 | 64 |
| I/O Pins | 54 | 54 | 39 | 39 | 54 | 54 |
| Supply Voltage (V) | 2.0 to 3.6 | 2.0 to 3.6 | 2.0 to 3.6 | 2.0 to 3.6 | 2.0 to 3.6 | 1.8 to 5.5 |
| Operating Temperature (C) | -40 to +85 | -40 to +85 | -40 to +85 | -40 to +85 | -40 to +85 | -40 to +85 |
| Approximate Unit Price (USD) | 12.50 (qty 1) | 11.80 (qty 1, similar) | 10.50 (qty 1) | 10.20 (qty 1) | 13.40 (qty 1) | 4.50 (qty 1) |
Principaux différenciateurs
- Lowest-BOM 8-bit single-chip Ethernet solution (vs PIC18F66K90-I/PT + external ENC28J60)
- Most flash in TQFP-64 PIC18F Ethernet family (vs PIC18F66J60-I/PT and PIC18F66J55-I/PT)
- Highest pin count and I/O in 8-bit Ethernet MCU class (vs PIC18F66J60-I/PT)
Notes de conception
The PIC18F67J60T-I/PT requires a single 3.3V rail on VDD (2.0V-3.6V range). The internal 2.5V LDO powers the core, so no separate 2.5V supply is needed. Place a 100nF decoupling capacitor on each VDD pin and a single 10uF bulk capacitor near the supply entry point. Estimated: at full 41.667 MHz CPU load the core current is approximately 15 mA, plus 100 mA peak for Ethernet activity. Use a low-noise LDO such as the MCP1700 or AP2112 with the standard 1uF ceramic output capacitor.
The integrated 10BASE-T Ethernet MAC/PHY has dedicated analog pins (TPIN, TPOUT, RBIAS, ETHREF). Place the 12.4k RBIAS resistor and 1.9k ETHREF resistor within 5mm of the respective pins with a quiet ground via. Per Microchip reference designs, keep the TPOUT traces at 100 ohm differential and short (under 25mm). Route AVSS/AVDD traces separately from digital VDD/VSS to prevent digital switching noise from coupling into the analog Ethernet signals.
Each PIC18F67J60 needs a unique MAC address. Program a factory MAC address via Microchip's programming service, or store a custom MAC in the Flash user ID area and copy it to Ethernet registers at startup. Estimated: a 6-byte MAC may be pre-programmed in the last 6 bytes of Flash configuration memory. Do not skip the MAC address initialization, or the Ethernet peripheral will fail to transmit or receive.
For reliable 10BASE-T operation, use a 1:1 isolation transformer (such as the Pulse H1102 or equivalent) rated for 10Mbps. Place the transformer within 25mm of the TPOUT and TPIN pins. The transformer secondary side connects to the RJ-45 jack with 75 ohm center-tapped termination per IEEE 802.3. Per Microchip reference designs, do not omit the Bob Smith termination on the unused RJ-45 lines, or radiated emissions will fail FCC Class B.
Informations de conformité
RoHS compliant per Microchip product page and DigiKey listing. Not AEC-Q100 qualified (industrial grade only). Conflict-minerals declaration available from Microchip.
