PIC24EP32GP204-E/MV - 60 MIPS 32KB Flash 16-bit MCU | Microchip
부품 번호: PIC24EP32GP204-E/MV ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $2.63 | $2.63 |
| 10 | $2.45 | $24.50 |
| 100 | $2.18 | $218.00 |
| 500 | $1.92 | $960.00 |
| 1,000 | $1.74 | $1,740.00 |
PIC24EP32GP204-E/MV 개요
A 16-bit microcontroller (MCU) is a programmable processor with a 16-bit data path, register file, and ALU, sitting hierarchically above 8-bit MCUs and below 32-bit ARM Cortex-M devices in the embedded processing taxonomy: 16-bit MCU -> microcontroller -> embedded processor -> semiconductor. The PIC24EP family targets high-performance general-purpose applications where 8-bit cores lack throughput but full 32-bit MCUs are over-spec. The 'E' suffix indicates enhanced analog features including operational amplifiers, comparators, CTMU (Charge Time Measurement Unit), and a Peripheral Trigger Generator (PTG) for hardware-state-machine automation.
Key features include a 70 MIPS capable core (60 MIPS at this device's speed grade), 32KB self-programmable Flash with ECC, 4KB SRAM, multiple 16-bit timers, a 10/12-bit ADC, two op-amps, two comparators, USB-friendly peripherals, and multiple UART/SPI/I2C interfaces. Communication interfaces include up to two UARTs, two SPI, and two I2C ports, plus a Parallel Master Port on selected variants.
Architecturally, the PIC24EP uses a modified Harvard architecture with separate program and data paths, a hardware multiplier/Divide engine, and DSP extensions that allow single-cycle MAC operations. The PTG peripheral allows complex timing sequences to run without CPU intervention, freeing the core for application-level processing. The 48-pin UQFN with exposed pad provides thermal dissipation appropriate to the core's 60 MIPS throughput.
Typical applications include industrial motor control, automotive body electronics (AEC-Q100 grade on the standard PIC24EP32GP204-I/MV is required for automotive deployment - this -E variant is extended-temperature industrial), sensor signal conditioning using the on-chip op-amps, and USB device/host peripherals. The on-chip CTMU simplifies capacitive touch and time-of-flight measurements.
When designing with this part, ensure the exposed pad is soldered to a sufficiently large copper pour to meet thermal and electrical ground requirements. The device operates from a single 3.3V supply, and the configuration bits must be set correctly for oscillator selection and watchdog behavior.
This page synthesizes distributor pricing, AEC-Q100 compliance notes, drop-in alternatives in the same UQFN-48 footprint, and practical design notes not consolidated in the manufacturer datasheet.
드롭인 대체품: PIC24EP32GP204-E/MV — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: PIC24EP32GP204-E/MV (동일 폼 팩터 및 풋프린트) — 차이점: ADC, Package, CTMU, Program Memory (Flash), Comparators.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
PIC24EP32GP204-I/MV
✅ 드롭인✓ 재고 있음
$3.02 / 개
데이터시트 보기 →dsPIC33EP32GP204-E/MV
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
dsPIC33EP32GP204-I/MV
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC24EP64GP204-E/MV
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC24EP128GP204-E/MV
✅ 드롭인✓ 재고 있음
$5.42 / 개
데이터시트 보기 →PIC24EP32GP203-E/MV
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
PIC24EP32GP204-E/MV 최대 정격 & 전기적 특성
| Core Architecture | 16-bit PIC24E modified Harvard |
| Program Memory (Flash) | 32 KB (10.7K x 24) |
| RAM | 4 KB |
| Maximum CPU Speed | 60 MIPS |
| Operating Voltage (VDD) | 3.0 V to 3.6 V |
| 동작 온도 | -40C to +125C (extended) |
| 패키지 | 48-pin UQFN (6x6 mm) with exposed pad (MV) |
| ADC | 10/12-bit SAR ADC |
| Op-Amps | 2 on-chip operational amplifiers |
| Comparators | 2 on-chip comparators |
| CTMU | Yes (Charge Time Measurement Unit) |
| PTG (Peripheral Trigger Generator) | Yes |
| UART | Up to 2 |
| SPI | Up to 2 |
| I2C | Up to 2 |
| Timers | Multiple 16-bit timers |
| AEC-Q100 | Not qualified (industrial extended-temp -E suffix) |
| RoHS 상태 | Compliant |
| 실장 유형 | Surface Mount |
PIC24EP32GP204-E/MV 48-pin uqfn (6x6 mm) with exposed pad (mv) 핀 구성 가이드
PIC24EP32GP204-E/MV(48-pin uqfn (6x6 mm) with exposed pad (mv) 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: PIC24EP32GP204-E/MV.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
PIC24EP32GP204-E/MV 적합 용도: 6 애플리케이션s: Industrial Motor Control, Automotive Body Electronics (Industrial Tier), USB Device Peripherals, Sensor Signal Conditioning and IoT Edge Nodes, Medical Device Sub-Systems, Power Conversion and Digital Power Control.
Industrial Motor Control
The PIC24EP32GP204-E/MV fits closed-loop motor control at 60 MIPS with on-chip op-amps for current sensing, the 10/12-bit ADC for back-EMF feedback, and the PTG peripheral for hardware-driven PWM timing without CPU intervention. Per the Microchip PIC24EP family datasheet, the core's single-cycle MAC supports Field-Oriented Control (FOC) algorithms on PMSM or BLDC motors when implemented in firmware. The extended -40C to +125C temperature grade tolerates the cabinet environment of industrial drives, while the UQFN-48 exposed pad handles the part's thermal load at full CPU throughput. Compared to a discrete DSP solution, this part consolidates the controller, op-amps, and PWMs in one footprint.
추천
Automotive Body Electronics (Industrial Tier)
The PIC24EP32GP204-E/MV serves industrial-tier body-electronics applications such as HVAC actuators, lighting controllers, and seat-control modules where full AEC-Q100 grade is not required. Its on-chip CTMU simplifies capacitive-touch button decoding for interior lighting, while the dual UART/SPI/I2C interfaces handle LIN or CAN-bus bridges via external transceivers. The extended -40C to +125C temperature rating tolerates under-dash thermal stress. Note that AEC-Q100 grade on PIC24EP devices uses a different suffix (e.g., -VAO variants on Microchip's auto-qualified family); engineers targeting true automotive qualification should select the AEC-Q100 version. The UQFN-48 footprint integrates well with space-constrained body-controller PCBAs.
추천
USB Device Peripherals
The PIC24EP32GP204-E/MV supports USB device functionality via the PIC24EP family's USB peripheral (on selected package pins), enabling it to serve as a CDC, HID, or vendor-class USB device for industrial instrumentation, HID input panels, or PC-side data loggers. The 32KB Flash accommodates full USB stacks including enumeration, class drivers, and application-level command handling. The 60 MIPS throughput ensures responsive USB interrupt latency, while the on-chip CTMU simplifies capacitive button decoding on touch-equipped panels. The UQFN-48 package with exposed pad delivers thermal headroom for sustained USB throughput on densely populated PCBAs. A 48 MHz external crystal is typically used as the USB clock reference per the family datasheet.
추천
Sensor Signal Conditioning and IoT Edge Nodes
The PIC24EP32GP204-E/MV integrates two on-chip op-amps that simplify analog front-end design for bridge sensors, RTDs, and 4-20 mA current loops used in industrial IoT edge nodes. Combined with the CTMU for capacitive sensing and the 12-bit ADC for precision measurement, the part supports low-component-count sensor hubs. The 60 MIPS throughput handles AES-128 or similar lightweight crypto in firmware for secure data uplink. The UQFN-48 package plus extended temperature grade suit outdoor or cabinet-mounted sensor installations. For wireless IoT, an external SPI-connected radio module such as Microchip's RN2483 or MRF24WN0MA is paired on a wire-bound bus.
추천
Medical Device Sub-Systems
The PIC24EP32GP204-E/MV's extended temperature range, deterministic interrupt latency, and 60 MIPS throughput make it a candidate for non-life-critical medical sub-systems such as patient-room environmental monitors, asset-tracking tags, and laboratory instrumentation controllers. The on-chip op-amps and 12-bit ADC support precision bio-signal front-ends when paired with appropriate external protection circuitry. The UQFN-48 footprint allows compact PCBAs suitable for handheld medical devices. Note that medical-device end-product certification is the OEM's responsibility; the PIC24EP32GP204 is not FDA-cleared as a medical component. For safety-critical applications, additional redundancy and IEC 60601 / IEC 62304 compliance must be designed into the host system.
추천
Power Conversion and Digital Power Control
The PIC24EP32GP204-E/MV's 60 MIPS throughput, hardware PWM with PTG-driven sequencing, and high-resolution ADC make it suitable for digital power conversion controllers in industrial and renewable-energy applications. Per the PIC24EP family datasheet, the PTG peripheral coordinates high-resolution PWM outputs for multi-phase buck or PFC stages without CPU overhead, while the ADC samples feedback at rates that enable sub-100 ns duty-cycle corrections. The extended temperature grade handles the elevated ambient of power-cabinet environments. Compared to a dedicated digital-power controller IC, this part provides more flexibility in switching topology at the cost of needing firmware development. The UQFN-48 exposed pad delivers the thermal headroom required for sustained PWM-intensive operation.
추천
추천 제품 요약
엔지니어링 참조 데이터: PIC24EP32GP204-E/MV — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | PIC24EP32GP204-I/MV | dsPIC33EP32GP204-E/MV | PIC24EP64GP204-E/MV | PIC24EP128GP204-E/MV |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 48-pin UQFN (MV) | 48-pin UQFN (MV) - same | 48-pin UQFN (MV) - same | 48-pin UQFN (MV) - same | 48-pin UQFN (MV) - same |
| Program Flash | 32 KB | 32 KB | 32 KB | 64 KB | 128 KB |
| RAM | 4 KB | 4 KB | 4 KB | 8 KB | 16 KB |
| CPU Throughput | 60 MIPS | 60 MIPS | 60 MIPS + DSP engine | 60 MIPS | 60 MIPS |
| DSP Engine | No | No | Yes | No | No |
| Temperature Grade | -40C to +125C (E) | -40C to +85C (I) | -40C to +125C (E) | -40C to +125C (E) | -40C to +125C (E) |
| Op-Amps / Comparators | 2 / 2 | 2 / 2 | 2 / 2 | 2 / 2 | 2 / 2 |
주요 차별점
- Same-footprint DSP drop-in via dsPIC33EP variant (vs dsPIC33EP32GP204-E/MV)
- Extended temperature grade in same package as -I variant (vs PIC24EP32GP204-I/MV)
- Memory upgradability within the same footprint (vs PIC24EP64GP204-E/MV / PIC24EP128GP204-E/MV)
설계 노트
The UQFN-48 (MV) package exposes the central thermal pad on the underside, which must be soldered to a sufficiently large PCB ground pour for thermal dissipation and electrical reference. Recommended layout: a single contiguous copper area under the exposed pad with at least 12 thermal vias (0.3 mm drill, 0.6 mm pad) stitching to internal ground planes. Without proper soldering of the EP, the device's thermal performance degrades significantly, potentially causing thermal shutdown under heavy peripheral activity. Per Microchip's UQFN-48 package design guidelines, the EP should not be used as a signal pin even though the device's GND pins are also exposed.
Decouple the VDD/VSS pairs with a 100 nF ceramic capacitor placed within 2 mm of each pin pair, and add a bulk 4.7 uF to 10 uF tantalum or ceramic capacitor at the board's power entry point. The PIC24EP32GP204-E/MV's analog reference (AVDD/AVSS) requires its own dedicated 100 nF bypass; sharing the digital VDD capacitor risks ADC noise injection. The device operates from 3.0V to 3.6V; voltages outside this range cause undefined behavior. For USB applications, ensure the VUSB pin is connected to a regulated 3.3V and decoupled with 100 nF + 4.7 uF per the family datasheet.
Configuration bits must be explicitly set before any code execution - watchdog timer, oscillator selection, JTAG/debugger disable, and brown-out reset all have factory defaults that may not match the application. Code-protection bits (CP, CPD) must be configured correctly or debug access will be locked out, requiring device erasure with a debugger. The PGECx/PGEDx programming pins must not be left floating during reset, as this may trigger unintended programming mode entry. Always verify configuration word settings with MPLAB X's code configurator before programming production units.
Keep analog signals (ADC inputs, op-amp inputs) routed on a separate PCB layer or guarded with ground traces away from digital switching signals, particularly PWM outputs and SPI clock traces. The on-chip ADC's 12-bit performance depends on clean analog supply and ground, with the AGND pin tied to a star-ground point at the device. For op-amp configurations, route feedback and gain-setting resistors close to the chip to minimize parasitic capacitance that affects stability at higher frequencies. The PTG peripheral's hardware-triggered events should be considered when assigning pin functions to avoid conflicts.
규정 준수 정보
RoHS compliant per Microchip product page. AEC-Q100 NOT qualified on the -E/MV variant (extended temperature, not automotive); for AEC-Q100 grade, contact Microchip for the automotive part number with separate suffix. Lead-free and conflict-minerals compliance confirmed through Microchip's public CMRT declarations.
