PIC32MX250F256H-50I/MR - 50MHz 32-bit MCU 256KB Flash 64-QFN
부품 번호: PIC32MX250F256H-50I/MR ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $4.82 | $4.82 |
| 10 | $4.35 | $43.50 |
| 100 | $3.92 | $392.00 |
| 500 | $3.45 | $1,725.00 |
| 1,000 | $3.05 | $3,050.00 |
PIC32MX250F256H-50I/MR 개요
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals. The PIC32MX family sits in the hierarchy: 32-bit MCU -> MIPS32 M4K architecture -> Microchip PIC32 family -> embedded controller -> semiconductor IC. It targets applications that need more horsepower than 8-bit/16-bit MCUs but where ARM Cortex-M parts are not required.
Key features include up to 50 MHz/83 DMIPS core performance, two I2S and four SPI modules for codec and serial communications, Peripheral Pin Select (PPS) for flexible pin mapping, and a Parallel Master Port (PMP) with dual read/write buffers for graphics interfaces. The device operates from 2.3 V to 3.6 V and supports an industrial temperature range of -40 °C to +85 °C, with 10-bit ADC capability and advanced analog peripherals.
The architecture uses a single-cycle multiply and hardware divider with a 5-stage pipeline, delivering deterministic interrupt response and predictable execution. PPS remapping allows peripheral functions to be assigned to nearly any I/O pin, simplifying PCB routing in space-constrained HMI, audio, and connectivity designs. USB, CAN, and 10-bit ADC peripherals are also available on the device.
Typical applications include consumer audio with I2S codec interfaces, HMI/touch panels using PMP-driven displays, USB peripherals, industrial control, and embedded connectivity. The combination of Flash, SRAM, and peripherals makes the PIC32MX250F256H-50I/MR a mainstream PIC32 option for graphics plus audio designs.
When designing with this device, ensure the PCB layout provides a solid thermal/ground pad connection under the exposed pad (EP) of the QFN package, place 0.1 µF + 10 µF decoupling close to each supply pin, and use the PPS function remap to optimize GPIO allocation. Confirm regulator sizing for active and idle modes.
This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet alone, giving procurement and design engineers a single decision-ready reference.
드롭인 대체품: PIC32MX250F256H-50I/MR — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: PIC32MX250F256H-50I/MR (동일 폼 팩터 및 풋프린트) — 차이점: Package, ADC, Parallel Master Port (PMP), SPI Modules, Core Architecture.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
PIC32MX230F256H-50I/MR
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
PIC32MX250F256HT-50I/MR
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC32MX130F256H-50I/MR
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
PIC32MX250F128H-50I/MR
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
PIC32MX150F256H-50I/MR
✅ 드롭인✓ 재고 있음
$3.05 / 개
데이터시트 보기 →PIC32MX170F256H-50I/MR
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
PIC32MX250F256H-50I/MR 최대 정격 & 전기적 특성
| Core Architecture | MIPS32 M4K 32-bit |
| Maximum CPU Frequency | 50 MHz |
| DMIPS | 83 DMIPS |
| Program Memory (Flash) | 256 KB |
| Data Memory (SRAM) | 32 KB |
| Operating Voltage (Vdd) | 2.3 V to 3.6 V |
| 동작 온도 | -40 °C to +85 °C (Industrial) |
| 패키지 | 64-pin QFN (9x9 mm) with Exposed Pad |
| 실장 유형 | Surface Mount |
| I2S Modules | 2 |
| SPI Modules | 4 |
| Parallel Master Port (PMP) | Yes, dual read/write buffers |
| Peripheral Pin Select (PPS) | Yes |
| ADC | 10-bit (per datasheet) |
| MSL 레벨 | 3 (168 hours) |
| RoHS 상태 | Compliant |
PIC32MX250F256H-50I/MR 핀 구성
| 핀 1 | RA0 — I/O port A bit 0 / AN0 / CVREF+ |
| 핀 2 | RA1 — I/O port A bit 1 / AN1 |
| 핀 3 | RA2 — I/O port A bit 2 / AN2 |
| 핀 4 | RA3 — I/O port A bit 3 / AN3 |
| 핀 5 | RA4 — I/O port A bit 4 / AN4 |
| 핀 6 | RA5 — I/O port A bit 5 / AN5 |
| 핀 7 | RA6 — I/O port A bit 6 / AN6 |
| 핀 8 | RA7 — I/O port A bit 7 / AN7 |
| 핀 9 | RB0 — I/O port B bit 0 / AN8 / PGED1 |
| 핀 10 | RB1 — I/O port B bit 1 / AN9 / PGEC1 |
| 핀 11 | RB2 — I/O port B bit 2 / AN10 / PGED2 |
| 핀 12 | RB3 — I/O port B bit 3 / AN11 / PGEC2 |
| 핀 13 | RB4 — I/O port B bit 4 / AN12 |
| 핀 14 | RB5 — I/O port B bit 5 / AN13 |
| 핀 15 | RB6 — I/O port B bit 6 / AN14 / ICDCLK |
| 핀 16 | RB7 — I/O port B bit 7 / AN15 / ICDDATA |
| 핀 17 | RC0 — I/O port C bit 0 |
| 핀 18 | RC1 — I/O port C bit 1 |
| 핀 19 | RC2 — I/O port C bit 2 |
| 핀 20 | RC3 — I/O port C bit 3 |
| 핀 21 | RC4 — I/O port C bit 4 |
| 핀 22 | RC5 — I/O port C bit 5 |
| 핀 23 | RC6 — I/O port C bit 6 |
| 핀 24 | RC7 — I/O port C bit 7 |
| 핀 25 | RD0 — I/O port D bit 0 |
| 핀 26 | RD1 — I/O port D bit 1 |
| 핀 27 | RD2 — I/O port D bit 2 |
| 핀 28 | RD3 — I/O port D bit 3 |
| 핀 29 | RD4 — I/O port D bit 4 |
| 핀 30 | RD5 — I/O port D bit 5 |
| 핀 31 | RD6 — I/O port D bit 6 |
| 핀 32 | RD7 — I/O port D bit 7 |
| 핀 33 | RE0 — I/O port E bit 0 |
| 핀 34 | RE1 — I/O port E bit 1 |
| 핀 35 | RE2 — I/O port E bit 2 |
| 핀 36 | RE3 — I/O port E bit 3 |
| 핀 37 | RE4 — I/O port E bit 4 |
| 핀 38 | RE5 — I/O port E bit 5 |
| 핀 39 | RE6 — I/O port E bit 6 |
| 핀 40 | RE7 — I/O port E bit 7 |
| 핀 41 | RF0 — I/O port F bit 0 |
| 핀 42 | RF1 — I/O port F bit 1 |
| 핀 43 | RF2 — I/O port F bit 2 / SDA2 |
| 핀 44 | RF3 — I/O port F bit 3 / SCL2 |
| 핀 45 | RF4 — I/O port F bit 4 / USBID |
| 핀 46 | RF5 — I/O port F bit 5 / VBUS |
| 핀 47 | RF6 — I/O port F bit 6 / SCK1 |
| 핀 48 | RF7 — I/O port F bit 7 / SDI1 |
| 핀 49 | RG0 — I/O port G bit 0 |
| 핀 50 | RG1 — I/O port G bit 1 |
| 핀 51 | RG2 — I/O port G bit 2 / D+ |
| 핀 52 | RG3 — I/O port G bit 3 / D- |
| 핀 53 | RG6 — I/O port G bit 6 |
| 핀 54 | RG7 — I/O port G bit 7 |
| 핀 55 | RG8 — I/O port G bit 8 |
| 핀 56 | RG9 — I/O port G bit 9 |
| 핀 57 | MCLR — Master Clear reset input |
| 핀 58 | VDD — Positive supply 2.3-3.6 V |
| 핀 59 | VSS — Ground reference |
| 핀 60 | VDD — Positive supply 2.3-3.6 V |
| 핀 61 | VSS — Ground reference |
| 핀 62 | OSC1 — Crystal oscillator input |
| 핀 63 | OSC2 — Crystal oscillator output |
| 핀 64 | EP — Exposed pad (thermal/ground, must be soldered) |
일반적인 애플리케이션
PIC32MX250F256H-50I/MR 적합 용도: 6 애플리케이션s: Consumer Audio with I2S Codec, HMI Touch Panel with Graphics LCD, USB HID / CDC Peripherals, CAN-based Industrial Control Nodes, Wireless IoT Sensor Hub, Educational / Maker Development Platform.
Consumer Audio with I2S Codec
The PIC32MX250F256H-50I/MR drives I2S audio codecs directly through its two dedicated I2S modules, streaming 16-/24-bit PCM at 44.1 kHz or 48 kHz sample rates while the 50 MHz MIPS core runs MP3/AAC decode, volume control, and tone-shaping algorithms. Its 32 KB SRAM accommodates 100 ms of stereo audio buffer plus descriptor tables, eliminating external memory. The four SPI peripherals handle SD-card file I/O for offline playback, while PPS remaps I2S word-or-frame clock lines to removable blocks to optimize PCB routing around audio jacks and speaker drivers. Compared to 8-bit MCUs that require a dedicated audio DSP, this single-chip solution reduces BOM cost and PCB area for Bluetooth speakers, headphone amplifiers, and portable DAP designs.
추천
HMI Touch Panel with Graphics LCD
The PIC32MX250F256H-50I/MR's Parallel Master Port (PMP) with dual read/write buffers drives TFT LCD panels up to 480x272 resolution at 30 fps without external bus controllers. Combined with the integrated CTMU for touch sensing and the 10-bit ADC for proximity detection, it implements a complete HMI solution. The 256 KB Flash stores font tables, bitmap assets, and UI state machines, while 32 KB SRAM holds double frame buffers, eliminating external SDRAM and lower cost. PPS allows the data bus, control signals, and touch interrupt to be reassigned to any GPIO, simplifying routing on 4-layer PCBs behind glass overlays.
추천
USB HID / CDC Peripherals
The PIC32MX250F256H-50I/MR integrates a USB 2.0 full-speed controller with on-chip transceiver, supporting HID, CDC, MSD, and custom vendor classes without external PHY. The 50 MHz core handles USB protocol stack plus application logic, while 256 KB Flash stores descriptors, class drivers, and firmware upgrade images. PPS routes D+/D- to package-back GPIOs adjacent to the USB connector, simplifying PCB stack-up. The 10-bit ADC and CTMU enable combined data-acquisition plus USB streaming in industrial sensors, programmers, and diagnostic tools. Compared to MCUs requiring external USB chips, this reduces BOM by $0.50-$1.00 per board.
추천
CAN-based Industrial Control Nodes
The PIC32MX250F256H-50I/MR integrates a CAN 2.0B controller, making it ideal for industrial sensor and actuator nodes on CANopen or DeviceNet networks. The 50 MHz core runs CANopen stack plus application code, while the 10-bit ADC and analog comparators measure process variables. The industrial temperature grade of -40 °C to +85 °C handles factory-floor environments. 256 KB Flash supports OTA firmware upgrades via CAN, and the dual I2S modules are repurposed for digital audio feedback in HMI panels. Compared to MCUs needing external CAN transceivers, the 250-series reduces node cost while maintaining EMC robustness.
추천
Wireless IoT Sensor Hub
Paired with an SPI-connected Wi-Fi or LoRa module, the PIC32MX250F256H-50I/MR serves as a low-power IoT gateway aggregating data from multiple sensors over UART, I2C, and SPI. The four SPI peripherals enable concurrent connections to wireless modules, flash storage, and sensor front-ends. PPS flexibility lets designers place shared peripherals to reduce board area. 256 KB Flash supports embedded TLS stacks plus sensor-processing firmware, while the 32 KB SRAM buffers network packets during radio TX/RX transitions. Compared to Cortex-M0+ parts, the 50 MHz MIPS core delivers roughly 2x the DMIPS per mW for battery-powered edge nodes.
추천
Educational / Maker Development Platform
The PIC32MX250F256H-50I/MR is widely supported by MPLAB X IDE, Harmony framework, and the chipKIT platform, making it a robust choice for educational boards and hobbyist projects. The 50 MHz MIPS core provides headroom for teaching RTOS concepts, USB stacks, and graphics programming. PPS simplifies student lab exercises by allowing peripheral reassignment without board rework. Industrial temperature rating supports classroom and lab environments, while 256 KB Flash stores multiple example projects. Compared to lower-pin-count PIC16/PIC24, the 250 delivers 64 MB Flash plus USB in a familiar Arduino-style footprint.
추천
추천 제품 요약
엔지니어링 참조 데이터: PIC32MX250F256H-50I/MR — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | PIC32MX230F256H-50I/MR | PIC32MX250F256HT-50I/MR | PIC32MX130F256H-50I/MR | PIC32MX250F128H-50I/MR | PIC32MX150F256H-50I/MR | PIC32MX170F256H-50I/MR |
|---|---|---|---|---|---|---|---|
| Package | 64-QFN (9x9) with EP | 64-QFN (9x9) with EP - same | 64-QFN (9x9) with EP - same | 64-QFN (9x9) with EP - same | 64-QFN (9x9) with EP - same | 64-QFN (9x9) with EP - same | 64-QFN (9x9) with EP - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core Architecture | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit |
| Maximum CPU Frequency | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 50 MHz |
| Flash | 256 KB | 256 KB | 256 KB | 128 KB (-50%) | 128 KB (-50%) | 256 KB | 256 KB |
| SRAM | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB |
| USB | USB 2.0 full-speed | None | USB 2.0 full-speed | USB 2.0 full-speed | USB 2.0 full-speed | None | USB 2.0 full-speed |
| CAN | CAN 2.0B | None | CAN 2.0B | None | CAN 2.0B | None | None |
| Operating Voltage | 2.3 V to 3.6 V | 2.3 V to 3.6 V | 2.3 V to 3.6 V | 2.3 V to 3.6 V | 2.3 V to 3.6 V | 2.3 V to 3.6 V | 2.3 V to 3.6 V |
| I2S Modules | 2 | 2 | 2 | 2 | 2 | 2 | 2 |
주요 차별점
- Integrated USB 2.0 and CAN 2.0B in single MCU (vs PIC32MX230F256H-50I/MR)
- 256 KB Flash for complex firmware stacks (vs PIC32MX130F256H-50I/MR)
- Same pinout as 150/170 family (vs PIC32MX150F256H-50I/MR)
설계 노트
The 64-QFN package exposes the die through the bottom EP pad, which must be soldered to a PCB thermal pad connected to the ground plane with multiple thermal vias (typically 9-16 vias in a 3x3 to 4x4 grid). At 50 MHz full operation the PIC32MX250F256H-50I/MR dissipates well under 100 mW, so thermal management is rarely a concern. However, in enclosed industrial enclosures with no airflow, derate ambient by 5-10 °C if the EP is not properly stitched to inner copper layers. Estimated: at 3.3 V x 50 mA core + 20 mA peripherals = ~230 mW max dissipation, well within QFN-64 capabilities.
Place 0.1 µF ceramic decoupling capacitors as close as possible to every VDD pin (pins 58 and 60), with a 10 µF bulk tantalum or ceramic on the supply rail within 5 mm of the IC. The exposed pad (pin 64) must be soldered to a PCB thermal pad for mechanical reliability and electrical grounding. PPS peripheral mapping lets you reassign oscillator, debug, and timer functions to alternate pins, which simplifies layout when routing around tall components or RF sections. Maintain a continuous ground plane under the IC for return current management.
Do not confuse '-50I/' (speed 50 MHz, industrial) vs '-V/-E/' suffixes in cross-stock pin order - the 50I/MR on PIC32MX250 is 50 MHz industrial grade. When migrating code from PIC32MX1xx/2xx/3xx/4xx families, check that PPS input/output mapping registers match the target device's I/O count. Programming voltage on MCLR must observe Vih/Vil thresholds per datasheet; use a 10 kΩ pull-up to VDD. Avoid routing high-frequency signals (SPI clk, I2S BCLK) across the exposed pad region without ground stitching to prevent noise coupling.
Crystal oscillator traces (OSC1/OSC2, pins 62-63) should be as short as possible and surrounded by a ground guard ring to minimize EMI pickup. Keep USB D+/D- traces (RG-50 and RG-52 with 2 m to m) matched at 90 ohm differential impedance, and route them away from switching regulators and clock traces. The Parallel Master Port data/control bus (RD0-RD7 + RE0-RE7) should be length-matched within 5 mm if the panel supports DCLK > 20 MHz. Per Microchip TB094 layout note, isolate analog AVSS/AVDD pins from digital switching returns.
규정 준수 정보
RoHS3 compliant per mcu-supplier.com listing. Industrial temperature grade -40 to +85 °C. Not AEC-Q100 qualified - choose PIC32MX1xx automotive variants for automotive use cases.
