S9S12C128J2VFUE - 16-Bit 128KB Flash 80-QFP MCU | NXP
부품 번호: S9S12C128J2VFUE ✗ 단종| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $0 | $0.00 |
| 10 | $0 | $0.00 |
| 100 | $0 | $0.00 |
| 500 | $0 | $0.00 |
| 1,000 | $0 | $0.00 |
S9S12C128J2VFUE 개요
A microcontroller is a programmable integrated circuit that combines a processor core, memory, and peripherals in one package. The S12C family combines a 16-bit core with flash-based program memory and is positioned for general-purpose industrial and automotive network applications. Unlike a simple logic device, the S9S12C128J2VFUE can execute embedded software, manage external interfaces, and control system behavior through its integrated peripherals.
The verified listing identifies the device as a 16-bit MCU with an S12 core, 128 KB flash, 25 MHz operation, automotive qualification, and an 80-QFP package. A separate distributor listing describes the related HCS12 device as 50 MHz; because the verified sources conflict on maximum frequency, the package-level claims should be confirmed against the applicable NXP datasheet before selecting timing, clocking, or firmware configurations.
Typical embedded uses include automotive body or network electronics, industrial controllers, sensor interfaces, actuator controllers, and communication equipment where a low-cost 16-bit microcontroller with on-board flash is useful. The 80-QFP package provides a larger pin count than small 32-pin devices, potentially supporting more external signals and peripheral connections while requiring careful PCB layout.
When designing a board around this MCU, verify the exact pinout, power rails, clock configuration, reset requirements, and peripheral multiplexing in the NXP datasheet. Do not infer compatibility from the package name alone. The QFP footprint and exposed lead arrangement must match exactly, and firmware should be tested against the intended voltage, temperature, and automotive operating conditions.
This page consolidates the verified component identity, package information, source listings, and practical selection considerations. It also distinguishes confirmed facts from data that requires manufacturer-documentation review, helping engineers avoid treating conflicting distributor descriptions as final design specifications.
드롭인 대체품: S9S12C128J2VFUE — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
이 제품에는 사용 가능한 드롭인 대체품이 없습니다.
대체품 요청S9S12C128J2VFUE 최대 정격 & 전기적 특성
| Product Type | 16-bit HCS12 microcontroller |
| Processor Core | S12 core |
| Flash Memory | 128 KB |
| Flash Organization | 128K x 8 |
| Maximum Frequency | 25 MHz in the NXP component summary; distributor listing also states 50 MHz |
| Temperature Range | -40°C to +105°C |
| Temperature Grade | Automotive qualified |
| 패키지 | 80-QFP, 14 x 14 mm |
| Terminal Count | 80 terminals |
| Terminal Form | Gull wing |
| Package Shape | Square |
| 실장 유형 | Surface mount |
| Core Architecture | 16-bit |
| Application Category | General-purpose industrial and automotive network applications |
| Manufacturer | NXP Semiconductors / Freescale Semiconductor |
| AEC-Q100 Qualification | Automotive qualified; exact qualification wording and grade require manufacturer confirmation |
S9S12C128J2VFUE square 핀 구성 가이드
S9S12C128J2VFUE(square 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: S9S12C128J2VFUE.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
S9S12C128J2VFUE 적합 용도: 6 애플리케이션s: Automotive Body Control Module, Industrial Sensor Aggregation, Actuator and Motor Control, Automotive Network Gateway, Communication Equipment, Instrumentation and Test Equipment.
Automotive Body Control Module
The S9S12C128J2VFUE fits an automotive body-control role when the design needs a 16-bit HCS12 processor, 128 KB of flash, and the verified -40°C to +105°C temperature range. The 80-QFP package offers more external connection capacity than a small low-pin-count MCU, making it useful for distributed switch inputs, actuator outputs, and communication interfaces. Because the component is described as automotive qualified, engineers can evaluate it for extended-temperature vehicle electronics, but the exact qualification grade, EMC behavior, diagnostic coverage, and safety requirements still require NXP documentation. Firmware should verify reset behavior, clock setup, and peripheral multiplexing before production release.
추천
Industrial Sensor Aggregation
The S9S12C128J2VFUE can serve as the central controller in an industrial sensor node because its 16-bit S12 core and 128 KB flash provide embedded program storage for acquisition logic, filtering, diagnostics, and communication handling. Its verified -40°C to +105°C range is suitable as a starting point for extended-temperature environments, while the 80-QFP package can accommodate external sensors, transceivers, and status signals. The verified material does not specify ADC resolution, I/O count, serial interfaces, or operating voltage, so those resources must be checked in the manufacturer datasheet. A practical design should reserve filtering, watchdog, and fault-safe behavior for sensor and actuator faults.
추천
Actuator and Motor Control
For actuator or motor-control subsystems, the S9S12C128J2VFUE can execute position logic, timing, limit handling, and supervisory functions while the verified 128 KB flash stores application code. The 16-bit architecture is appropriate for embedded control tasks that need more computational headroom than an 8-bit controller, and the 80-QFP package provides a larger pin count for control signals and external drivers. However, the verified data does not identify PWM channels, timer resolution, motor-driver interfaces, current limits, or voltage rails. Those specifications must be confirmed before assigning the MCU to a power stage, and the thermal design must be validated for the actuator enclosure and ambient temperature.
추천
Automotive Network Gateway
The S9S12C128J2VFUE is a plausible candidate for a gateway that must run protocol handling and supervisory logic on a flash-based 16-bit MCU. The verified 128 KB flash capacity gives a defined code-storage target, while the 80-QFP package can expose the required external communications and diagnostic connections. The part is listed for automotive network applications and has a verified -40°C to +105°C range, making it more relevant to extended-temperature vehicle systems than a standard consumer MCU. Before selecting it, verify CAN, LIN, UART, SPI, or other interface availability, transceiver requirements, bus timing, ESD strategy, and the exact electrical limits; those details are not present in the supplied snippets.
추천
Communication Equipment
The S9S12C128J2VFUE can be evaluated for embedded communication equipment where a 16-bit controller, 128 KB flash, and extended-temperature operation are useful. It could manage protocol state machines, supervisory timers, configuration storage, and low-speed communication tasks, depending on the peripherals supplied by the exact device. The package’s 80 gull-wing terminals provide ample routing opportunities for external transceivers and logic, but the verified data does not identify communication interfaces or I/O voltage limits. Engineers should compare the exact S9S12C128J2VFUE peripheral set against the site-listed MC9S12DJ128VFUE and confirm EMC, grounding, and bus termination in the final schematic review.
추천
Instrumentation and Test Equipment
The S9S12C128J2VFUE may fit instrumentation front ends and embedded measurement controllers when the system needs local flash, a 16-bit processing core, and operation across the verified -40°C to +105°C range. Its 128 KB flash can hold measurement sequencing, calibration handling, diagnostics, and communication firmware, while the 80-QFP package exposes a relatively broad connection set for sensors, displays, and control logic. The supplied data does not specify ADC performance, timer accuracy, analog reference quality, or supply rails, so precision-measurement suitability cannot be determined from the component summary alone. Validate acquisition accuracy, reference stability, grounding, and calibration storage experimentally.
추천
추천 제품 요약
엔지니어링 참조 데이터: S9S12C128J2VFUE — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 |
|---|---|
| Package | 80-QFP, 14 x 14 mm |
| Brand | NXP Semiconductors |
| Architecture | 16-bit S12 core |
| Flash Memory | 128 KB, 128K x 8 |
| Frequency | 25 MHz in NXP summary; 50 MHz in one distributor listing |
| Temperature Range | -40°C to +105°C |
| Qualification | Automotive qualified |
| Terminal Count | 80 terminals |
| Package Form | Square gull-wing QFP |
| Application Category | General-purpose industrial and automotive network applications |
주요 차별점
- Extended-temperature automotive positioning (vs S9S12C128J2CFUE)
- Integrated flash capacity (vs MC9S12DJ128VFUE)
- Large-pin-count QFP integration (vs MC9S12HZ128VAL)
설계 노트
Treat the 80-QFP footprint as a manufacturer-controlled mechanical and electrical interface. Confirm pad geometry, pin-1 orientation, courtyard, solder mask, and assembly clearance against the applicable NXP package drawing before layout release. The verified snippets confirm an 80-terminal 14 x 14 mm QFP but do not provide the land pattern, so generic QFP dimensions should not be copied into production files without checking the exact package documentation.
Do not select power rails or decoupling values from the distributor summaries alone. The supplied data does not state operating voltage, supply current, analog-supply requirements, or absolute maximum limits. Before schematic release, verify every supply and ground pin in the complete NXP datasheet, then design local bypass capacitance and power sequencing around the device's actual requirements. This is especially important for automotive systems where transient voltage and temperature behavior can exceed nominal test conditions.
Validate clock, reset, debug, and communication routing against the actual device pinout and timing specifications. The verified material confirms a 16-bit S12 core and flash capacity but does not identify clock pins, reset polarity, debug signals, or peripheral multiplexing. Keep sensitive analog and communication routes away from noisy switching nodes, provide defined return paths, and verify signal integrity with the intended clock and load configuration. Do not infer pin functions from the 80-pin count alone.
The main sourcing risk is treating the conflicting 25 MHz and 50 MHz descriptions as interchangeable. Treat the NXP device documentation and exact ordering suffix as authoritative, and record the source and revision used during design review. Also avoid assuming that S9S12C128J2CFUE is a drop-in substitute: the verified temperature ranges differ, and pin, electrical, qualification, and firmware compatibility have not been established in the supplied data.
Although the verified temperature range reaches +105°C, the available data does not provide power dissipation, thermal resistance, or maximum supply-current data. Estimate junction temperature only after obtaining verified operating voltage, current, package thermal resistance, and ambient conditions. In an automotive enclosure, include copper area, airflow assumptions, neighboring heat sources, and worst-case operating mode in the thermal review; the temperature grade alone does not guarantee safe self-heating.
규정 준수 정보
The verified component listing states automotive qualified and gives a -40°C to +105°C temperature range. The supplied data does not provide RoHS, REACH, lead-free, halogen-free, conflict-minerals, or exact AEC-Q100 grade documentation; these fields remain unknown or require manufacturer confirmation.
