SN75121N - Dual 2/0 Line Driver, 16-PDIP | Texas Instruments
부품 번호: SN75121N ✓ 활성SN75121N 개요
A line driver is an interface IC that converts a digital logic signal into a stronger output suitable for transmission through a cable, bus, or other wired connection. In the electronic-component hierarchy, the SN75121N belongs to the line-driver family within interface ICs and broader digital communication and signal-conditioning systems. Its purpose is to restore signal amplitude and loading capability after a source device has driven a line through an electrically demanding interconnect.
The SN75121N provides two independent driver channels in a 2/0 organization, meaning two outputs and no corresponding input-driver designation in the product description. Its emitter-follower output topology provides low output impedance, while the uncommitted outputs support wired-OR logic. These characteristics make the device useful where multiple signal sources must share a transmission line under properly controlled pull-up or pull-down arrangements.
The low-impedance outputs are intended for terminated lines such as coaxial cable and twisted pair. When calculating transmission-line performance, account for the 50-to-500-ohm line range identified by Texas Instruments. Logic compatibility simplifies connection with conventional TTL systems, while the 16-pin DIP format supports through-hole construction and prototype boards where a surface-mount package is unnecessary.
Typical applications include industrial control links, point-to-point digital communication, instrument interfaces, legacy computer peripherals, and factory equipment that uses balanced or unbalanced terminated connections. The device can also support bus arrangements where wired-OR behavior is intentional. Application-specific timing, cable length, termination, and noise-margin requirements still need to be validated in the complete system.
The primary design consideration is the output-stage implementation. Because the outputs are uncommitted and use emitter-follower behavior, the board designer must provide the correct biasing, termination, pull-up or pull-down arrangement, and signal-return path. Do not assume that a line will remain valid solely because the driver can source current; verify voltage levels, edge rate, bus contention, cable capacitance, and receiver thresholds in the finished design.
This page organizes the Texas Instruments SN75121N around its verified line-driver function, package, interface characteristics, replacement choices, comparison parameters, and practical implementation concerns. It is intended to help engineers identify the correct package variant, distinguish genuine pin-compatible alternatives from merely similar drivers, and plan the surrounding termination and signal-integrity circuitry before committing a design to production.
드롭인 대체품: SN75121N — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: SN75121N (동일 폼 팩터 및 풋프린트) — 차이점: Logic Compatibility, Output State, Product Type.
SN55121N
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
SN75122N
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
SN75123N
✅ 드롭인가격 문의
데이터시트 보기 →SN75124N
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →SN75121N 사양
| Product Type | Dual line driver |
| Driver Configuration | 2/0 |
| Number of Driver Channels | 2 channels |
| Supported Line Impedance | 50 ohm to 500 ohm |
| Logic Compatibility | Standard TTL |
| Output Topology | Low-impedance emitter follower |
| Output State | Uncommitted output |
| Logic Function | Wired-OR capable |
| Supported Transmission Line | Terminated coaxial cable or twisted pair |
| Package Type | 16-pin through-hole DIP |
| Package Designation | 16-PDIP |
| 실장 유형 | Through-hole |
SN75121N 16-pdip 핀 구성 가이드
SN75121N(16-pdip 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: SN75121N.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
SN75121N 적합 용도: 6 애플리케이션s: Point-to-Point Digital Data Links, Industrial Control Equipment Interfaces, Coaxial Cable Data Transmission, Twisted-Pair Communication, Wired-OR Shared-Line Logic, Legacy Computer and Peripheral Interfaces.
Point-to-Point Digital Data Links
The SN75121N fits point-to-point links that need a stronger line interface than a conventional logic output can provide. Its two low-impedance emitter-follower channels can drive terminated coaxial cable or twisted pair with line impedances from 50 to 500 ohms, while standard TTL compatibility simplifies the logic side of the design. The transmitter should be configured with the correct termination and signal-return path, and system timing must remain within the selected receiver's requirements.
Industrial Control Equipment Interfaces
The SN75121N can support legacy industrial equipment interfaces that use TTL-compatible dual line-driver channels over copper wiring. Two independent channels are useful for command, acknowledgment, or status signaling when the physical line supports the specified 50-to-500-ohm impedance range. Industrial implementation should add the required surge, isolation, grounding, and enclosure measures, and must verify the device's temperature and regulatory requirements for the final equipment category.
Coaxial Cable Data Transmission
The SN75121N's low-impedance emitter-follower outputs are suitable for driving terminated coaxial cable in digital transmission arrangements. The 50-to-500-ohm line range covers multiple common cable impedances, and the 2/0 organization provides two transmit channels in one 16-pin DIP device. For reliable operation, select the proper remote termination, maintain a controlled return path, account for cable capacitance and attenuation, and verify edge-rate performance with the actual receiver.
Twisted-Pair Communication
A twisted-pair interface can use the SN75121N when the circuit requires TTL-compatible drive levels and terminated lines. Its low output impedance helps the transmitter handle the load presented by a cable network, while the dual-channel configuration can carry two related signals. Twisted-pair construction can improve noise rejection when the signal and return conductors are handled correctly, but termination balance, skew, grounding, and common-mode behavior still require board-level validation.
Wired-OR Shared-Line Logic
The SN75121N is appropriate for a deliberately designed wired-OR bus because Texas Instruments identifies its outputs as uncommitted. The external bias network and output-state behavior become part of the interface architecture, allowing multiple compatible sources to share a line under controlled conditions. Designers must prevent simultaneous active outputs from causing destructive contention, select suitable current limits, and confirm that every receiver recognizes the resulting valid low and high states.
Legacy Computer and Peripheral Interfaces
The SN75121N can be used when maintaining or expanding legacy digital peripheral connections based on TTL-compatible line signaling. Its dual channels allow one cable to carry two one-way signals, and its emitter-follower outputs can drive terminated coax or twisted pair. Retrofitting should begin with a complete signal audit because older equipment may rely on unusual wired-OR behavior, termination, or timing that must be preserved rather than modernized with an electrically different interface.
엔지니어링 참조 데이터: SN75121N — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | SN55121N | SN75122N | SN75123N | SN75124N |
|---|---|---|---|---|---|
| Package | 16-pin through-hole DIP | 16-pin through-hole DIP | 16-pin through-hole DIP | 16-pin through-hole DIP | 16-pin through-hole DIP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Driver Configuration | 2/0 | Dual line driver; detailed configuration not verified | Dual line driver; detailed configuration not verified | 2/0 | Dual line driver; detailed configuration not verified |
| Number of Driver Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
주요 차별점
- Dual emitter-follower outputs with wired-OR capability (vs SN75121N)
- Direct 50-to-500-ohm transmission-line support (vs SN75122N)
- Established standard-TTL interface (vs SN75123N)
설계 노트
Route each driver channel with the transmission-line geometry appropriate to its impedance. Keep the logic input traces short and place the required input and output bypass components near the IC according to the manufacturer guidance. For a through-hole DIP implementation, preserve a direct ground return and avoid long loops between the device ground pins and the cable shield or receiver reference.
Validate termination, rise time, reflections, and receiver noise margin with the actual cable and load rather than relying only on the 50-to-500-ohm line-impedance statement. The SN75121N uses low-impedance emitter-follower outputs, so the output state, pull network, and remote termination jointly determine the waveform. Check that the selected receiver recognizes every valid bus state and that no unused driver channel produces an active output.
Do not substitute a driver solely because it has the same 16-pin DIP outline. Confirm pin functions, output-stage behavior, supply levels, input thresholds, propagation timing, and output-state requirements against the manufacturer documentation for the exact MPN. SN75113N and SN75174N are related line-driver products but have different driver organizations, so they are not included as direct drop-in choices.
Use a controlled return path and apply the appropriate cable shield termination to reduce common-mode noise and prevent the line from behaving as an unintended antenna. The uncommitted outputs allow application-defined biasing, which can increase sensitivity to noise if the pull network is weak or slow. Review rise time, current demand, and EMI filtering together before raising line speed.
규정 준수 정보
No exact-package compliance declaration was identified for SN75121N. Confirm RoHS, REACH, lead-free, halogen-free, and conflict-minerals status for the exact manufacturer ordering configuration before production release.